WOHLER VIS 40 mm Pan And Tilt Camera Head User Manual
- June 1, 2024
- WOHLER
Table of Contents
WOHLER VIS 40 mm Pan And Tilt Camera Head
Product Information
Specifications
- Camera Type: 1/4 COLOR CMOS
- Protection: Waterproof according to IP 67 (30 minutes up to 1 meter deep)
- Light Sources: 10 white LEDs
- Emitter Frequency: 9.2 kHz
- Lens System: f = 2.6 mm, F = 2.4
- Working Temperature:
Product Usage Instructions
- The camera head should be securely connected to the cable or rod using the provided clutch socket with 8 poles. Ensure a tight connection to maintain a waterproof seal.
- Use the keys on the camera system to control the pan and tilt functions of the camera head. Ensure proper alignment for accurate viewing.
- The home function automatically aligns the camera head to a straight position, ensuring it looks straight ahead. Press the SHIFT key followed by the HOME key on the camera system’s keyboard to activate this function.
- Ensure the transmitter is activated in the camera menu. Clean the lens using a clean damp cloth without any cleaning agents to prevent damage.
FAQ
- Q: What should I do if the camera head is not responding to controls?
- A: Check the connection between the camera head and the cable or rod, ensuring it is secure and waterproof. Also, verify that the transmitter is activated in the camera menu.
- Q: How do I activate the home function?
- A: Press the SHIFT key followed by the HOME key on the camera system’s keyboard to activate the home function and align the camera head to a straight position.
General Information
Operation Manual In-formation
- This operation manual allows you to work safely with the Wöhler Camera Head. Please keep this manual for your information.
- The Wöhler Camera Head should be employed by professionals for its intended use only.
- Liability is void for any damages caused by not following this manual.
Notes
ATTENTION!
Not following this note can cause permanent damage to the device.
NOTE!
Useful information
Intended Use
- The Wöhler pan and tilt camera head is designed for the inspection of pipes, air ducts chimneys, water lines, and ventilation lines.
- It has to be connected to the Wöhler VIS camera system.
Transport
ATTENTION!
- Improper transport can harm the camera head.
- Always transport the camera head in the provided box to prevent damage.
Information on disposal
- Electronic equipment does not belong to domestic waste but must be disposed of per the applicable statutory provisions.
Manufacturer
Wöhler Technik GmbH
- Wöhler-Platz 1
- 33181 Bad Wünnenberg
- Tel.: +49 2953 73-100 Fax: +49 2953 73-96100 E-Mail: info@woehler.de.
Technical Data
| Specification
---|---
Type| 1/4“ COLOR CMOS
Pan and tilt| 360° / 180°
Protection| Waterproof according to IP 67
Field of View| 70°
Light Source| 10 white LEDs
Emitter frequency| 9,2 kHz
Lens system| f = 2,6 mm or 0.1”
F = 2,4
Size| Ø 40 mm or 1.5 “
Operation temperature| 0 to 40 °C or
32 to 104°F,
RH 95% max
Working temperature| -29 to 50 °C or
-20.2 to 122 °F ,
RH 95% max
Elements of the camera head
Connecting the camera cable or rod
The pan and tilt miniature camera head is connected via a clutch socket with 8 poles to the cable or the rod.
- Plug the camera head and camera cable or the rod together.
- Turn the thread clockwise for closing the screw connection tightly for a waterproof con-nection.
ATTENTION!
Only a tight connection guarantees a waterproof connection.
Controlling the camera head
- The pan and tilt camera head is controlled by the keys of the camera system.
Home-Function
- The home function ensures the camera head is automatically aligned to a straight position, ensuring the camera “looks straight ahead”.
- Moreover, when the user presses the HOME key, the camera head aligns itself so that the display is parallel with the ground above (this function is deactivated if the camera head faces 90° upwards or downwards. Under these circumstances, the optics can only be guided forwards).
- To activate the home function, press the SHIFT key and then the HOME key on the keyboard of the camera system.
Localisation
- The Wöhler camera head Ø 40 mm is equipped with a transmitter coil that transmits signals. These signals can be located by the Locator Wöh-ler L 200. This way it is possible to locate the exact position of the camera head in the pipe sys-tem.
Maintenance
NOTE!
The transmitter has to be activated in the camera menu (setup menu).
- Clean the lens only with a clean damp cloth but never with the cleaning agent.
Warranty and Service
Warranty
Each Wöhler camera head will be tested in all functions and will leave our
factory only after extensive quality control testing. The guarantee period for
the meter is 12 months from the date of the sale, provided that it is used
correctly.
This warranty does not cover the freight and packaging costs when the device
is sent to the factory for repair. Service by non-authorized personnel or
making modifications camera head voids any warranty.
Service
Wöhler has built our reputation on excellence in customer service. Therefore,
of course, we are readily available to assist you after the warranty period
ends.
- Send us the device and we will repair it and return it to you with our package service.
- Immediate help is provided by our technical staff over the telephone.
Declaration of conformity
- The manufacturer :
- WÖHLER Technik GmbH
- Wöhler-Platz 1, D-33181 Bad Wünnenberg
- Declares that the product:
- Pan and tilt camera head Wöhler Ø 40 mm
- Wöhler VIS
- complies with the essential protection requirements of Council directive 2014/30/CE on the approximation of the laws of the Member States relating to electromagnetic compability.
- The meter conforms to the following standards:
- EN 55024
- EN 55022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>