warpple LS5 Smart Projector User Manual

Smart Projector LS5
User Manual

Package Contents

Safety Instructions

If physical injury, loss of data, or damage is caused by failure to follow instructions, the warranty does not apply.

1. Do not look straight at the operation beam. The bright light may damage your eyes.
2. Do not block the projection lens with any objects when the device is under operation a$this could cause objects to become heated and deformed or even cause a fire.
3. Do not block or clog the air ventilation. Always leave at least 20 clearance around this device for ventilation.
4. Poteet this device from overexposure to direct sunlight, heat, large temperature fluctuations, and moisture.
5. 4orbid the fan to blow directly to the ventilation.
6. Avoid extreme vibrations and always handle this device with care.
7. Disconnect the power cord from the AC outlet if the projector is not being used for a long period of time.
8. Do not make any repairs to this device yourself only have your device repaired by an authorized service center.

Overview

User Interface

Home Page

Get Started

1. Connect to power
   Connect the power cord to the power adapter. Connect the power adapter to the DC IN jack of the projector Connect the power cord plug to a power outlet

2. Power on
   Press the projector’s power button

3. Follow the instructions on the screen to complete the initial setup.

Customer Service
Contact Us
warpple.com/contact

https://lihi1.com/dLjE6

Limited Warranty

Warpple warrants its products to be free from defects in material and workmanship, under normal use, for 12 months from the date of purchase if a product proves to be defective in material or workmanship during the warranty period, Warpple will, at its sole option, repair or replace the product with a like product. A replacement product or parts may include remanufactured or refurbished parts or components. This warranty is valid only for the first consumer purchaser You will need to provide your product’s serial number For information about receiving service under warranty, please refer to www.warpple.com Information in this document may change without notice.

FCC Compliance Statement

This device complies with part 1s of #Cc #Rules. Operation is subject to the following two conditions ( 1 ) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class
8digital device, pursuant to part 1 of the see Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, 0es, and can radiate radio frequency energy. and it is not installed and used in accordance with the instructions, my Cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a Circuit  rom different that to which the receiver is connected
Consult the dealer or an experienced radio/IW technician for help
The antenna4used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter
The device was tested and complies with measurement standards and procedures specified in FCC CrR Tile 47 Part 15 C Subpart Warning You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment

Conformity for European Countries
This product complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with
Directive 2011/65/EU of the European Parliament and the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment (Ro4S2 Directive) is deemed to comply with the  maximum concentration values issued by the European Technical Adaptation
Committee (TAC) as shown below

Polybrominated diphenyl ethers
(PBDE)| 0.10%| <0.1%
Bis(2-Ethylheyl) phthalate(DEHP)| 0.10%| <0.1%
Benzyl butyl phthalate(8BP)| -1%| <0.1%
Dibutyl phthalate(0BP)| 0.10%| <0.1%
Diisobutyl phthalate(0IBP)| 0.10%| «0.1%

Certain components of products as stated above are exempted under the Annex Ill of the Ro4S2 Directives as noted below. Examples of exempted components are: in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and £EFL) for special purposes not exceeding (per lamp)
Short length (500 mm) maximum 3.5 mg per lamp Medium length [» 500 mm and 1,500 mm): maximum S mg per lamp long length (> 1,500 mm) maximum 13 mg per lamp.
Mercury lead in a glass of cathode ray tubes leads in a glass of fluorescent tubes not exceeding 0.2% by weight. lead as an alloying element in aluminum containing up to04%lead b weight.
A copper alloy containing up to 4% lead by weight lead in high melting temperature type solders [ie. lead-based alloys containing 85% by weight or more lead)
Electrical and electronic components containing lead a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectric devices, or in a glass or ceramic matrix  compound in
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE) The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>