Pyle PDIC60T 2 Way in Wall in Ceiling Stereo Speaker Instruction Guide
- June 3, 2024
- Pyle
Table of Contents
Pyle PDIC60T 2 Way in Wall in Ceiling Stereo Speaker
Introduction
Thank you for purchasing this PYLE in-wall/in-ceiling speaker system. It is a state-of-the-art product carefully designed and manufactured for your installation needs, and has been thoroughly tested to ensure consistent and reliable performance.
If you have any question about the installation or operation of your PYLE in- wall/in-ceiling speaker system which are not answered by this manual, contact your dealer immediately.
INCLUDED
IN-CEILING SPEAKERS
SPEAKER PLACEMENT
FRONT SPEAKERS
INSTALLATION
The in-wall/in-ceiling speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer. please contact your dealer or a qualified installer.
TOOLS NEEDED
TROUBLESHOOTING
IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:
- Check that receiver/amplifier is on and a source is playing.
- Check all wires and connections between receiver amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
- Review proper operation of your receiver/amplifier.
IF THERE IS NO SOUND COMING FROM ONE SPEAKER:
- Check the “Balance” control on your receiver/amplifier.
- Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
IF THERE IS LOW (OR NO) BASS OUTPUT:
- Make sure the connections to the left and right “Speaker Inputs· have the correct polarity{+ and-).
- Consider adding a powered subwoofer to your system.
- In Dolby Digital Of DTS modes. make sure your receiver/processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/ processor has been enabled. If no subwoofer is being used, make sure the left and nght front and rear speakers have been configured as “LARGE.” See your receiver/processor’s owner”s manual for futner information on correct speaker configuration in Dolby Digital, DTS and other surround sound modes.
IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:
- Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed. cut, punctured or touching each other.
- If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.’
WIRING DIAGRAM
REAR SPEAKERS
IN-CEILING
Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The front speakers should be placed the same distance from each’ other as they are from the listening position. They should be placed at about the same height from the floor as the listener’s ears will be, with the tweeters aimed toward the listener at ear-level height. In a home theater configuration, the two surround speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listener’s ears. If that is not possible, they may be placed in a wall (or in the ceiling) behind the listening position, facing forward. The surround speakers should not call attention to themselves. They should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers. In Dolby Digital and DTS systems, aim the tweeters toward the listening position at ear-level height.
SPEAKER CONNECTIONNS
CONNECTION TIPS
The wires for both speakers should be the same length. If one speaker is placed closer to the amplifier than the other, hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and (-) terminals. We use red to denote the (+) terminal and black for the (-) terminal. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and -) on the speaker to (-) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and a poor stereo image. With the advent of multi-channel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material.
EXISTING CONSTRUCTION
IN-CEILING SPEAKERS
-
Cut the drywall.
Note : Always allow at least one-half inch between a wall stud and the speaker cutout the locking tabs will not be able to swivel into place. -
Connect the speaker wires to the speaker.
-
Place the frame assembly in the wall
-
Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. Put in the strips of adhesive to secure the grille. The in-celling speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grile, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further.
-
Replace the metal grille
After installing the speaker grille, gently press on the mesh of the tweeter to adjust the position of the tweeter.
- MODEL NO. PDIWCS56
- Cut-out Dimensions: 14″(w) x 6.4″(H) x3″(D)
- Dimensions (each speaker) 6″(w)x7.6″(H)x3.6″(D)
Frequently Asked Questions
How can I attach an amplifier to Pyle PDIC60T ceiling speakers?****
Drill a hole for the wires. After ensuring sure the amplifier is unplugged, shut off the breaker. Install the wiring. Start connecting the wires to the ceiling speaker terminals. The terminals of the amplifier should be connected to the other end of the cables. By activating your circuit breaker, you can give it a try.
What power needs does the Pyle PDIC60T ceiling speaker have?****
No, ceiling speakers typically function as passive speakers, which means that they are driven by speaker wires connected to an external amplifier because they lack built-in amplifiers. Binding posts are used to connect each ceiling speaker to the amp.
Can I connect my TV to my Pyle PDIC60T ceiling speakers?****
There will be an audio output on every TV. For the time being, it will most likely be a digital optical output. By connecting an analogue wire from your TV to the amplifier and turning on line output on your TV, you may listen to TV sound through your ceiling speaker system.
The Pyle PDIC60T ceiling speakers produce a fantastic sound, right?****
Actually, it’s a wonderful idea to play music over ceiling speakers. They might use surround sound to give you the impression that you are at a concert or live event.
Can the Pyle PDIC60T ceiling speakers play surround sound?****
Ceiling speakers are a great option if you want a home theatre experience with a more immersive audio experience. They must be specifically designed for ceilings, but they are still a great addition to a surround sound system.
Is power provided to the Pyle PDIC60T ceiling speakers?****
Passive speakers are often mounted on walls and ceilings. As a result, they are not need to be connected to a power source. They only need a power source and a receiver or amplifier to function.
Dolby Atmos and Pyle PDIC60T in-ceiling speakers cooperate?****
The majority of ceiling speakers work with Atmos. The majority of speaker options, including those for the ceiling, are compatible with Dolby Atmos if you’re building your own home theatre; older models might not be able to support this surround sound application.
Can ceiling speakers like the Pyle PDIC60T be mounted inside a wall?****
In-ceiling speakers can be used in place of in-wall speakers because of their similar audio output. The most obvious difference will be in size. In-wall speakers are typically larger than in-ceiling speakers.
Do the Pyle PDIC60T ceiling speakers perform admirably for rear surround, as you claim?****
No, your amplifier is not equipped to handle multichannel sound.
How do I connect a set of Pyle PDIC60T ceiling speakers to a receiver?****
Turn off all of the lights. Your cords should be sorted. Trim the ends of the wires. See the speaker wire arrangement. As soon as your wires arrive, plug them into the proper sockets. Cable locks are used to secure the sockets.
Can you watch TV with Pyle PDIC60T ceiling speakers?****
There will be an audio output on every TV. For the time being, it will most likely be a digital optical output. By connecting an analogue wire from your TV to the amplifier and turning on line output on your TV, you may listen to TV sound through your ceiling speaker system.
Right, the Pyle PDIC60T ceiling speakers sound good.****
Actually, playing music over ceiling speakers is a brilliant concept. They may make you feel as though you are at a concert hall or live event by using surround sound.
What ceiling speakers are better in quality than the Pyle PDIC60T?****
As a result, in-wall speakers often perform better in terms of quality and power than in-ceiling speakers. When positioned in different walls of a room or other location, in-wall speakers can add additional sound dimensions than just a downward-firing one.
Is Pyle PDIC60T ceiling speakers subwoofer-required?****
Even if ceiling speakers are able to handle all frequencies, a subwoofer will be helpful in handling the bass and low-end frequencies. Additionally, it significantly improves the overall sound quality of your sound system.
The power supply for the Pyle PDIC60T ceiling speakers is unknown.****
No, because ceiling speakers lack built-in amplifiers, they often operate as passive speakers, which means that they are powered by speaker wires connected to an external amplifier.
Is it possible to install ceiling speakers like the Pyle PDIC60T in a wall?****
Instead of in-wall speakers, in-ceiling speakers can be employed because their audio output is comparable. The size difference will be the most noticeable. Typically, in-wall speakers are bigger than in-ceiling speakers.
How do the ceiling speakers with Bluetooth Pyle PDIC60T work?****
Bluetooth ceiling speakers are frequently wirelessly controlled by a smartphone or other internet-capable device. The Bluetooth chip in the speaker will read the content from the smartphone and play it through the speaker.
The Pyle PDIC60T ceiling speaker system has bass, right?****
There is never a bass response point and a background sound field with in- ceiling speakers. They were created with the environment in mind.
How are the Pyle PDIC60T ceiling speakers measured?****
Take your measurements in inches for the speaker using a ruler or a tape measure. The biggest portion of the cone should face upward while your speaker is standing upright. Measure the distance between the mounting frame’s two edges at the speaker’s widest point. To ensure that you don’t forget the measurement later, write it down.
Can I use ceiling speakers for surround sound, such as the Pyle PDIC60T?****
Yes, provided that your amplifier can handle multichannel sound.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>