Godox X2T-C Wireless Flash Trigger User Manual

: June 9, 2024
: Godox

Table of Contents

X2T-C Wireless Flash Trigger
Foreword
Name of Parts
Battery
Setting the Flash Trigger
Compatible Flash Models
Technical Data
Restore Factory Settings
Firmware Upgrade
Attention
Caring for Flash Trigger
Warranty Conditions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

X2T-C Wireless Flash Trigger
User Manual

X2T-C Wireless Flash Trigger

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device, please contact the customer line.
✉ www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer
Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

Foreword

Thanks for your purchase of this X2T-C wireless flash trigger. This wireless flash trigger is suitable for using Canon cameras control Godox flashes with X system e.g. camera flash, outdoor flash, and studio flash. It can also control Canon original speedlites with the coordination of X1R-C receiver. Featuring multichannel triggering, stable signal transmission, and sensitive reaction, it gives photographers unparalleled flexibility and control over their setups. The flash trigger applies to hotshoe-mounted Canon EOS series cameras, as well as the cameras which have PC sync socket.
With X2T-C wireless flash trigger, high speed synchronization is available for most of camera flashes in the market which support E-TTL II. The max flash synchronization speed is up to 1/8000s.
: 1/8000s is achievable when the camera has a max camera shutter speed of 1/8000s.
Warning

Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
Always keep this product dry. Do not use in rain or in damp conditions.
Keep out of reach of children.
Do not use the flash unit in the presence of flammable gas. In certain circumstance please pay attention to the relevant warnings.
Do not leave or store the product if the ambient temperature reads over 50°C.
Turn off the flash trigger immediately in the event of malfunction.
Observe precautions when handling batteries.
- Use only batteries listed in this manual. Do not use old and new batteries or batteries of different types at the same time.
- Read and follow all warnings and instructions provided by the manufacturer.
- Batteries cannot be short-circuited or disassembled.
- Do not put batteries into a fire or apply direct heat to them.
- Do not attempt to insert batteries upside down or backwards.
- Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove batteries when the product is not used for a long time or when batteries run out of charge.
- Should liquid from the batteries come into contact with skin or clothing, rinse immediately with fresh water.

Name of Parts

Body

Godox X2T-C Wireless Flash Trigger - 1

Note: All the buttons have backlight, which is convenient for usage in dark environment.

Godox X2T-C Wireless Flash Trigger - 2

LCD Panel

Godox X2T-C Wireless Flash Trigger - 4

1. Channel (32)	7. Group
2. Camera Connection	8. Mode
3. Modeling Lamp Master Control	9. Power
4. High-Speed/Rear Curtain Sync	10. ZOOM Value
5. Sound	11. Version
6. Battery Level Indication

Battery

AA alkaline batteries are recommended.
Installing Batterie
As shown in the illustration, slide the battery compartment lid of the flash trigger and insert two AA batteries separately.

Battery Indication
Check the battery level indication on the LCD panel to see the remaining battery level during the usage.

Battery Level Indication	Meaning
3 grids	Full
2 grids	Middle
1 grid	Low
Blank grid	Low battery, please replace it.
Blinking	<2.5V The battery level is going to be used out immediately (please

replace new batteries, as low power lead to no flash or
flash missing in case of long distance).

The battery indication only refers to AA alkaline batteries. As the voltage of Ni-MH battery tends to be low, please do not refer to this chart.

Setting the Flash Trigger

Power Switch
Slide the Power Switch to ON, and the device is on and status indicator lamp will not reveal.
Note: In order to avoid power consumption, turn off the transmitter when not in use.
Automatically Enter Power Saving Mode

The system will automatically enter standby mode after stop operating the transmitter over 60 seconds. And the displays on the LCD panel disappear now.
Press any button to wake up. If the flash trigger is attached to the host shoe of CANON EOS camera, half press the camera shutter can also wake the system up.

Note: If do not want to enter power saving mode, press the

button to enter C.Fn custom settings and set STBY to OFF.
Power Switch of AF Assist Beam
Slide the AF-assist beam switch to ON, and the AF lighting is allowed to output. When the camera cannot focus, the AF assist beam will turn on, when the camera can focus, the AF assist beam will turn off.
Channel Setting

Short press the button and choose CH to set the channel value.
Turn the select dial to choose the appropriate channel. The channel value will be confirmed after exiting the menu.
This flash trigger contains 32 channels which can be changed from 1 to 32. Set the transmitter and the receiver to the same channel before usage.

Wireless ID Settings
Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless IDs and channels of the master unit and the slave are set to
the same.
Press the

button to enter C.Fn ID. Press the button to choose OFF channel explosion shutdown, and choose any figure from 01 to 99.
Note: It can only be used when the slave units have the wireless ID settings functions. If they do not have, please set the ID to OFF.
Mode Setting

After pressing the group button to select one group, press the button and all the current group’s mode will be changed by the order of TTL/M/–.
In normal situation, press the button to switch the multi-group mode to MULTI mode. Press the group selection button and then press the button can set the MULTI mode to ON or OFF.

Output Value Settings
In the M mode:

Press the group button to choose the group, turn the select dial, and the power output value will change from Min to 1/1 in 0.3 stop increments. Press the button to confirm the setting.
Press button to choose all group’s power output value, turn the select dial, and all groups power output value will change from Min to 1/1 in 0.3 stop increments. Press button again to confirm the setting.

Note: Min. refers to the minimum value that can be set in M or Multi mode. The minimum value can be set to 1/128 0.3, 1/256 0.3, 1/128/ 0.1, 1/256 0.1, 3.0(0.1) and 2.0(0.1) according to C.Fn-Min. For most of camera flashes, the minimum output value is 1/128 and cannot be set to 1/256. However, the value can change to 1/256 when using in combination with Godox strong power flashes e.g. AD600, etc.
Flash Exposure Compensation Settings
In the TTL mode:
Press the group button to choose the group, turn the select dial, and the FEC value will change from -3~3 in 0.3 stop increments. Press the button to confirm the setting.
Multi Flash Settings (Output Value, Times and Frequency)

In the multi flash (TTL and M icon are not displayed).
The three lines are separately displayed as power output value, Hz (flash frequency) and Times (flash times).
Press the button and turn the Select Dial to change the power output value from Min. to 1/4 in integer stops.
Press the button again and choose Hz to change flash frequency. Turn the select dial to change the setting value.
Press the button again and choose Times to change flash times. Turn the select dial to change the setting value.
Until all the amounts are set. Or during any value setting, short press the button to exit setting status.
In the multi flash setting submenu, short press the button to return to main menu when no values are blinking.

Note: As flash times are restricted by flash output value and flash frequency, the flash times cannot be surpassing the upper value that permitted by the system. The times
that transported to the receiver end are a real flash time, which is also related to the camera’s shutter setting.
Modeling Lamp Settings
Long press the

button for 2 seconds to control the ON/OFF of the modeling lamp.
ZOOM Value Settings
Short press the button to enter the ZOOM menu. Short press the button and turn the select dial, and the ZOOM value will change from AUTO/24 to 200. Choose the desired value and back to the main menu.
Note: The flash’s ZOOM should be set to Auto (A) mode before responding.

Shutter Sync Settings

High-speed sync: short press the button to enter the SYNC menu. Choose high-speed sync icon and is displayed on the LCD panel.
Second-curtain sync: short press the button to enter the SYNC menu. Choose second-curtain sync icon and is displayed on the LCD panel.

Godox X2T-C Wireless Flash Trigger - 9

Buzz Settings
Press the

button to enter C.Fn BEEP and press the button. Choose ON to turn on the BEEP while OFF to run off it. Press the button again to back to the main menu.

Godox X2T-C Wireless Flash Trigger - 10

Sync Socket Settings

Press the
button to enter C.Fn SYNC and press the
button to choose IN or OUT. Press the
button again to back to the main menu.
- When choosing IN, this sync socket will enable X2T-C trigger flash.
- When choosing OUT, this sync socket will send trigger signals to trigger other remote control and flash.

Godox X2T-C Wireless Flash Trigger - 11

SHOOT Function Settings
Press the

button to enter C.Fn SHOOT. Press the button to choose oneshoot or multi-shoots and press the button again to back to the main menu.
One-shoot: When shooting, choose one-shoot. In the M and Multi-mode, the master unit only sends triggering signal to the slave unit, which is suitable for one person photography for the advantage of power saving.
Multi-shoots: When shooting, choose multi-shoots, and the master unit will send parameters and triggering signals to the slave unit, which is suitable for multi person photography. However, this function consumes power quickly.
APP: Only send triggering signal when camera is shooting (control the flas’s parameters by smartphone APP)

Godox X2T-C Wireless Flash Trigger - 12

C.Fn: Setting Custom Functions
The following table lists the available and unavailable custom functions of this flash.

Custom Function| Function| Setting Signs| Setting and Description
---|---|---|---
SYNC| Shutter sync setting| | Front curtain
| High speed
| Second curtain
BLUE.T.| Bluetooth status setting| OFF| Off
ON| On
BEEP| Beeper| ON| On
OFF| Off
ZOOM| ZOOM setting| 24| AUTO/24-200
SCAN| Scan the spare channel| OFF| Odd
START| Start to find the spare channel
CH| Wireless| 01| 01-32
ID| Channel setting Wireless ID| OFF| Off
01-99| Choose any figure from 01-99 (the old version flashes cannot use this function temporarily)
PC SYNC| Sync cord jack| IN| Trigger X2T-C to fire flash
OUT| Output signal to trigger other remote control and flash
DELAY| Delay setting| OFF| Off
0.1ms-9.9ms| Set the firing delay in high- speed sync
SHOOT| | One-shoot| Only send triggering signals in the M & Multi mode when camera is shooting
| All-shoot| Send parameters and triggering signal when camera is shooting (suitable for multi person photography)
APP| APP| Only send triggering signal when camera is shooting (control the flash’s parameters by smartphone APP)
DIST| Triggering distance| 0-30m| 0-30m triggering
1-100m| 1-100m triggering
STEP| Power output value| 1/128(0.3)| The minimum output is
1/128(change in 0.3 step)
1/256(0.3)| The minimum output is
1/256(change in 0.3 step)
| | 1/128(0.1)| The minimum output is
1/128(change in 0.1 step)
---|---|---|---
| | 1/256(0.1)| The minimum output is
1/256(change in 0.1 step)
3.0(0.1)| The minimum output is
3.0(change in 0.1 step)
2.0(0.1)| The minimum output is
2.0(change in 0.1 step)
GROUP| Group| 5 (A-E)| 5 groups (A/B/C/D/E)
3 (A-C)| 3 groups (A/B/C)
STBY| Sleep| 60sec| 60 seconds
30min| 30 minutes
60min| 60 minutes
OFF| —
LIGHT| Backlighting time| 12sec| Auto off in 12 seconds
OFF| Always off
ON| Always lighting
LCD| Contrast ration of LCD panel| -3-+3| The contrast ratio can be set as integral number from -3 to +3

Using the Flash Trigger
Ass a Wireless Camera Flash Trigger
Take TT685C as an example:

Turn off the camera and mount the transmitter on camera hotshoe. Then, power on the flash trigger and the camera.
Short press the
button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”).
Turn on the camera flash, press the < > wireless setting button and the < > wireless icon and slave unit icon will be displayed on the LCD panel.
Press the button to set the same channel to the flash trigger, and press the button to set the same group to the flash trigger. (Note: please refer to the
relevant instruction manual when setting the camera flashes of other models).
Press the camera shutter to trigger and the status lamp of the flash trigger turns red synchronously.

As a Wireless Outdoor Flash Trigger
Take AD600B as an example.

Turn off the camera and mount the transmitter on camera hot shoe. Then, power on the flash trigger and the camera.
Short press the button to set channel, group, mode and parameter (refers to the contents of “Setting the Flash Trigger”).
Power on the outdoor flash and press the < > wireless setting button and the < > wireless icon will be displayed on the LCD panel. Long press the <GR/CH> button to set the same channel to the flash trigger, and short press the <GR/CH> button to set the same group to the flash trigger (Note: please refer to the relevant instruction manual when setting the outdoor flashes of other models).
Press the camera shutter to trigger and the status lamp of the flash trigger turns red synchronously.

As a Wireless Original Flash Trigger
Take 600EX RT as an example:

Turn off the camera and mount the transmitter on camera hot shoe. Then, power on the flash trigger and the camera.
Short press the button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”).
Attach the original flash to the X1R-C receiver. Press the button on the receiver to set the same channel to the flash the trigger and press the button to set the same group to the flash trigger (Note: please refer to the relevant instruction manual when setting the original camera flashes).
Press the camera shutter to trigger. And the status lamp of the camera flash and the flash trigger both turn red synchronously.

Godox X2T-C Wireless Flash Trigger - 15

As a Wireless Studio Flash Trigger
Take GS400II as an example:

Turn off the camera and mount the transmitter on camera hot shoe. Then, power on the flash trigger and the camera.
Short press the button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”).
Connect the studio flash to power source and power it on. Synchronously press down the <GR/CH> button and <S1/S2> button and the < > wireless icon will be displayed on the LCD panel. Long press the <GR/CH> button to set the same channel to the flash trigger, and short press the <GR/CH> button to set the same group to the flash trigger. (Note: please refer to the relevant instruction manual when setting the studio flashes of other models).
Press the camera shutter to trigger. And the status lamp of the camera flash and the flash trigger both turn red synchronously.

Note: As the studio flash’s minimum output value is 1/32, the output value of the flash trigger should be set to or over 1/32. As the studio flash do not have TTL and stroboscopic functions, the flash trigger should be set to M mode in triggering.

Godox X2T-C Wireless Flash Trigger - 16

As a Wireless Shutter Release Trigger
Operation method:

Turn off the camera. Take a camera remote cable and insert one end into the camera’s shutter socket and the other end to the shutter release port of X1R-C to connect. Power on the camera and the receiver.
Short press the button to set channel, group, mode and parameters refers to the contents of “Setting the Flash Trigger”).
Press the receiver’s button to set the same channel to the flash trigger and press the button to set the same group to the flash trigger.
Half press the < > button to focus and full press the button to shoot. Release the button until the status lamp turns to red.

Godox X2T-C Wireless Flash Trigger - 17

As a Flash Trigger with 3.5mm Sync Cord Jack
Operation method:

The connection method please refers to the contents of “As a Wireless Studio Flash Trigger” and “As a Wireless Shutter Release”.
Set the transmitter end’s sync cord jack as an output port. Operation: press the
button on the transmitter end to enter C.Fn settings. Then, set PC SYNC
to OUT mode.
Press the shutter normally and the flashes will be controlled by sync cord jack’s signal.

Godox X2T-C Wireless Flash Trigger - 18

Connect to Smartphone through Bluetooth
Using method:

Short press the button to enter BLUE.T. to open the Bluetooth. The Bluetooth ID will be displayed under ON.
Search “Godox Photo” in iPhone’s APP store and download the APP. Or install the APP by scanning the QR Code with your smartphone.
Open the APP and choose .
Connect the transmitter to the responded Bluetooth ID and enter the password to match (the initial password id “000000”).

Godox X2T-C Wireless Flash Trigger - 19 https://itunes.apple.com/us/app/godoxphoto/id1258982778

Full match and back to APP main interface.
When started the Bluetooth function, the Bluetooth icon will be displayed on thetransmitter’s panel.
Set the channels of the slave flash and the transmitter to the same, and parameter e.g. slave flash mode, power value, modeling lamp and beep can be controlled on the APP of the smartphone.
Use the APP of the smartphone for shooting after setting all the parameter.

Note: When successfully connected the flash trigger and smartphone APP, the auto sleep of the flash trigger can be set to 30 min.

Godox X2T-C Wireless Flash Trigger - 20

Compatible Smartphone Models
This flash trigger can be used on the following Smartphone models:

This table only lists tested Smartphone models, not all Smartphone. For the compatibility of other Smartphone models, a self-test is recommended.
Rights to modify this table are retained.

Compatible Flash Models

Transmitter	Receiver	Flash	Note
X2T-C	—	AD600 series/AD400 series/AD360II series AD200 series/V860II series

V/850II V350C/TT685 series/TT600/TT350C QuickerII series/QTII/SK II series DP II series/GSII|
X1R-C| 600EX- RT/580EXII/580EX/430EXII V860C| As there are so many camera
flashes in the market which are compatible with Canon speedlites, we do not test one by one.
XTR-16| AD360/AR400| The flashes with Godox wireless USB port
Quicker series/SK series/DP series
GT/GS series/Smart flash series| Can only be triggered
XTR-16S| V860C V850|

Note: The range of support functions: the functions that are both owned by X2T-C and flash.
The relationship of XT wireless system and X2 wireless system:

XT-16 (Code Switch)	****	****	****	****	****	****	****	****
X2 (Display Screen)	**** CH01	**** CH02	**** CH03	**** CH04	****
CH05	**** CH06	**** CH07	**** CH08
XT-16 (Code Switch)	****	****	****	****	****	****	****	****
X2 (Display Screen)	**** CH09	**** CH10	**** CH11	**** CH12	****
CH13	**** CH14	**** CH15	**** CH16

This flash trigger can be used on the following Canon EOS series camera models:

Godox X2T-C Wireless Flash Trigger - 21

This table only lists the tested camera models, not all Canon EOS series cameras. For the compatibility of other camera models, a self-test is recommended.
Right to modify this table are retained.
The cameras which are released before 2012 do not have TTL mode in their D and E group.
1500D(2000D/T7), 3000D(4000D): When the high-speed shutter is higher than 1000, there will be luminance edge of the photo.

Technical Data

Model	X2T-C
Compatible cameras	Canon EOS cameras (E-TTL II autoflash) Support for

the cameras that have PC sync socket.
Comatible smartphone (sync flash in M mode)| iPhone, Huawei, Samsung (see the compatible smartphone models for details)
Power supply| 2*AA batteries

Flash Exposure Control

TTL autoflash	E-TTL II
Manual flash	Yes
Stroboscopic flash	Yes

Function

High-speed snyc	Yes
Flash exposure compensation	Yes, ±3 stops in 1/3 stop increments
Flash exposure lock	Yes
Focus assist	Yes
Modeling lamp	Yes
Beeper	Yes
Wireless shutter	Control the beeper by the flash trigger. The receiver

end can control the camera shooting through the 3.5mm sync cord jack.
ZOOM setting| Adjust the ZOOM value by the transmitter
Firmware upgrade| Upgrade through the Type-C USB port
Memory function| Settings will be stored 2 seconds after last operation and recover after a restart.

Wireless Flash

Transmission range (approx.)	0-100m
Built-in wireless	2.4G
Modulation mode	MSK
Channel	32
Wireless ID	01-99
Group	5

Other

Display	Large LCD panel, backlighting ON or OFF
Dimension/Weight	72x70x58mm/90g
2.G Wireless Frequency Range	2413.0MHz-2463.5MHz
Max. Transmitting Power of 2.4G Wireless	5dbm

Restore Factory Settings

Hold the MODE button and power the flash trigger on and all parameters will restore the factory settings.

Firmware Upgrade

This flash tigger supports firmware upgrade through the Type-CUSB port. Updated information will be released on our official website.

USB connection line is not included in this product. As the USB port is a Type-C USB socket, please use Type-C USB connection line.
As the firmware upgrade needs the support of Godox G3 software, please download and install the “Godox G3” firmware upgrade software” before upgrading. Then, choose the related firmware file.

Attention

Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode.
Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to MF. If so, set it to AF.
Signal disturbance or shooting interference. Change a different channel on the device.
Operating distance limited or flash missing. Check if batteries are exhausted. If so, change them.

The Reason & Solution of Not Triggering in Godox 2.4G Wireless Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G
wifi router, Bluetooth, etc.)

To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G quipment in working.

Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not (the flash ready indicator is lighten) and the flash is not under the state of over-heat protection or other abnormal situation.

Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode (a preflash is needed in TTL mode).

Whether the distance between the flash trigger and the flash is too close or not

Please turn on the “close distance wireless mode” on the flash trigger (<0.5m)
Please set the C.Fn-DIST to 0-30m.

Whether the flash trigger and the receiver end equipment are in the low battery states or not.

Please replace the battery (the flash trigger is recommended to use 1.5V disposable alkaline battery).

Caring for Flash Trigger

Avoid sudden drops. The device may fail to work after strong shocks, impact or excess stress.
Keep dry. The product isn’t waterproof. Malfunction, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity.
Avoid sudden temperature changes. Condensation happened if sudden temperature changes such as the circumstance when taking the transceiver out of a building with higher temperature to outside in winter. Please put the transceiver in a handbag or plastic bag beforehand.
Keep away from strong magnetic field. The strong static or magnetic field produced by devices such as radio transmitters lead to malfunction.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
Natural wear and aging of consumables or components during use (such as batteries, etc.).
Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

EU Declaration of Conformity
Identification data of the manufacturer’s / importer’s authorized representative: Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
CIN: 27082440
Subject of the declaration:
Title: Flash Trigger
Model / Type: X2T-C
The above product has been tested in accordance with the standard(s) used to demonstrate compliance with the essential requirements laid down in the
Directive(s):
Directive No. 2014/53/EU
** Directive No. 2011/65/EU as amended 2015/863/EU
WEEE
** This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.