nedis FISC3650BK Film Scanner User Manual

FISC3650BK Film Scanner
User Manual

Film Scanner
For more information see the extended manual online: ned.is/fisc3650bk
FISC3650BK

Intended use

The Nedis FISC3650BK scans images from developed negative or slide film and converts them to digital images.
Film or slides are put through the scanner using the provided film holders.
The product runs on DIGITNOW! Software and connects to your computer using a provided USB cable. The product is exclusively intended for scanning negative film or slide film and converting it to a digital image.
The product functions exclusively in combination with the provided DIGITNOW! software. This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be done by children without supervision.
Any modification of the product may have consequences for safety, warranty, and proper functioning.

Specifications

Windows: 7 / 8 / 10 (32 / 64 bit)

Main parts (image A)

1. SCAN button
2. Status indicator LED
3. Casing
4. Brush
5. Negative film holder
6. Positive slide holder
7. CD-ROM with driver software
8. Mini USB port
9. Film holder slot
10. USB cable

Safety instructions

WARNING

• Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep this document for future reference.
• Only use the product as described in this manual.
• Do not use the product if a part is damaged or defective. Replace a damaged or defective device immediately.
• Disconnect the product from the electrical outlet and other equipment if problems occur.
• Do not expose the product to water or moisture.
• Do not expose the product to heat, cold or direct sunlight.
• Do not use the provided brush to clean the film.
• Only use the provided USB cable

Connecting the Film scanner

1. Connect Aq to a USB 2.0 port of your computer.

2. Connect the other end of A10 to A8.
   **** The film scanner is recognized automatically by the computer and is ready for use after a few moments.

3.  Insert A7 into your computer.

4. Install the driver software.

5. Run the software.

Feed film or slides into the scanner (Image B + C)

1. Open the film or slide holder by gently pulling the latch in the middle while firmly holding the back of the holder.
2. Place film in the film holder or place framed slides in the slides holder.
3. Close the holder. 4. Insert the holder arrow-first into A9.
4. Push until the first picture is centered.

Scanning (Image D)

1. Double click on the “DIGITNOW!” icon on the desktop.
2. Choose the film type D2, resolution D3, and the film size D4.
3. Click “Scan” (Windows) or “Take image” (Mac) D7 or press A1 to scan the picture. It takes several seconds to save your picture and show it on screen.
4. Adjustments D5 can be made to the saturation, brightness, contrast, and the level of each individual RGB channel.
5.  Click D6 to reset the adjustment levels to their defaults.
6. Push the holder further into A9 until you reach the next frame or slide.
7. Click D7.
8. Repeat for all remaining frames or slides.

Troubleshooting

light up.
Spots show up on the picture| The dirt inside the film scanner| Use A4 to clean the inside of the film scanner.
Dirt on the film| Clean the film with a specialised product. Do not use the provided brush to clean the film.

http://ned.is/FISC3650BK

Nedis BV
De Tweeling 28, 5215 MC ’s-Hertogenbosch
The Netherlands

Documents / Resources

| nedis FISC3650BK Film Scanner [pdf] User Manual
FISC3650BK Film Scanner, FISC3650BK, Film Scanner
---|---

References

• Smart solutions for your daily needs | Nedis

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>