KERBL 184602 GrumoX Cordless Clipper Instruction Manual

: June 3, 2024
: KERBL

Table of Contents

Safety
Charging
Scope of delivery
Operation, cleaning and care’
Troubleshooting
Technical data
Clipster, a brand of
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KERBL 184602 GrumoX Cordless Clipper Instruction Manual

Safety

Please read the instructions for use carefully before operating the clippers, especially the „Safety“ section. This will help you avoid possible hazards and protect against damage to the device due to misuse. Keep the instructions for use handy for future reference. If the device is passed on to a new owner, please also hand over these instructions for use.

Explanation of terms and symbols

The following terms are used in these instructions for use:

DANGER

If disregarded, can lead to serious injuries or death

WARNING

If disregarded, can lead to serious injuries (or death)

Note Information that should be observed when handling the device

Danger of an electric shock! The device may never be charged or operated while in the bath, shower, over a filled washbasin / other container.

Intended use

the clippers are used to trim hair/fur
the device is designed for indoor use only. It should not be operated outdoors (garden, terrace, etc.).
if the device is used in a manner that does not comply with the intended use and/or if modifications are made to the device, then this voids the manufacturer‘s warranty and liabilities

Important danger warnings

DANGER

keep the device, charging tray and connecting cable away from moisture, water and other liquids, and do not operate it with wet hands
do not immerse the device, charging tray and connecting cable under water or rinse off under running water
if the device should fall into water, it may not be used again afterwards
the integration of a residual-current-operated protective device, with a nominal tripping current of less than 30 mA, in the building installation provides additional protection. We recommend that you have your electrician install residual current protection for your power circuits.
the device must be disconnected from the power supply when the battery is charged or after at least 8 hours of pure charging time
if the battery does not fully charge after 8 hours, do not operate the device and contact the manufacturer

WARNING

The clipping head can become hot after extended use!

DANGER

The clipper may only be operated with a power pack that meets the specifications on the nameplate. The device may only be operated with a power pack that delivers the SELV output voltage specified on the device’s markings.

General safety instruction

DANGER

Never operate the device if:

the device, charging tray or connecting cable is damaged
the clipping head is damaged or chipped because this can injure the skin
the device is dropped, shows visible damage or its functionality is impaired
the device is damaged so that electrical components are exposed In each case, the device must be disconnected from the mains immediately!

This device can be used by children 8 years of age and older and by individuals with impaired physical, sensory or mental abilities or those with insufficient experience and knowledge to do so, if they are being supervised or have been trained on the safe use of the device and understand the underlying hazards. Children may not play with the device. Cleaning and user maintenance may not be performed by children without supervision.

children should be supervised at all times to ensure that they do not play with the device. Make sure that children do not injure themselves on the clipping head. Keep the device out of the reach of children.
also keep the packaging material, e.g. films, away from children
lay the connecting cable in such a way so that no one can trip over or step on it
protect the connecting cable from damage. Never pull on the connecting cable. Always remove the cable from the power outlet by grasping the power pack plug. Keep the cable away from hot surfaces. Check the connecting cable for damage on a regular basis.
never expose the device to temperatures under 0 °C or over +40 °C for long periods of time. Avoid direct sunlight.
repairs may only be performed by authorised personnel in order to avoid a hazard
disconnect the device from the power supply for maintenance and parts replacement
the clipping head may not be taken apart

Safety during operation

DANGER

Never touch or reach into the clipping head when the device is switched on

The clipping head must be cleaned on a regular basis and oiled at the corresponding locations to ensure problem-free operation.

The device must be switched off when:

you put the device down, e.g. to charge it or when you interrupt the cutting process for a brief period
you attach or remove the comb attachment
you clean or oil the device

Only use the clipper together with original accessories (charging tray, comb attachment,etc.).
Never use sharp objects (e.g. a tail comb) to remove dust or foreign objects from the interior of the device.

Charging

when the device is delivered, it is not yet ready for operation
before connecting the clipper to an outlet, make sure that the mains voltage matches the voltage listed on the nameplate of the power pack
in order to maintain the charge capacity of the battery, we recommend that you occasionally discharge the battery by operating the deviceuntil the motor stops
please charge the device for a full 8 hours before first use so that the included rechargeable battery is activated
please do not charge the device in temperatures under 0 °C or higher than 40 °C
please do not charge the device while exposed to direct sunlight or the heat of a radiator
the standard charge time is 300 minutes. Avoid extended charge times to prevent damage to the battery.
When the device is fully charged, it can be used for longer than 200 minutes. The control light illuminates green. During charging, the control light flashes red.
the clippers can be connected directly to the power supply using the power pack or charged using the charging tray and power pack

Scope of delivery

Clipper
Comb (3 mm)
Comb (6 mm)
Comb (9 mm)
Comb (12 mm)
Cleaning brush
Oil
Power pack
Charging tray
LED light
Supplementary accessories: thinning shears, nail trimmers, fur brush, fur shears, nail file
LED display

Operation, cleaning and care’

Switching on and off:

Press the On/Off switch to switch off the clippers (Fig. 1). The shearing speed is modified by pressing the plus or minus button. The LED display shows the remaining battery capacity in % (Fig. 2). An inadequate battery capacity is indicated by a red control light. This clipper can be used via its cable as well as without its cable. Connect the power pack to the device socket located on the bottom of the device. Connect the USB plug to the socket adapter, then to the power (Fig. 3). Alternatively, the charging tray with USB cable and socket adapter can be used (Fig. 4).
cleaning and care

Cutting height adjustment:

The clippers have a 4-stage cutting height adjustment (1.0 / 1.3 / 1.6 / 1.9 mm). The cutting height can be modified by pressing the sliding switch while simultaneously pressing the unlocking button (Fig. 5).

Using the comb accessory:

Make sure that the clipper is switched off when installing and removing the comb. Four combs areavailable (3, 6, 9, 12 mm) for different cutting lengths. Place the comb onto the clipping head, making sure that it engages on the side (fig. 6).

Clean and oil the device on a regular basis to ensure the problem-free function and full functional performance of the clippers.

Cleaning the clipping head:

Switch the device off. Disconnect the device from the power supply. Remove the comb attachment and press in the centre of the shearing blades to remove them (fig. 7). Remove the hair with the cleaning brush.

Place the clipping head back onto the clippers as shown in fig. 8. Make sure that the locking mechanism is positioned properly and press the clipping head onto the device until it engages.
cleaning and care

Oiling the clipping head:

Remove the comb attachment. Use the brush to clean the cutting edge, removing the hair between the blades. Oil the locations where the upper and lower part of the clipping head touch. The device must be oiled immediately when the shearing performance diminishes noticeably or the temperature of the clipping head seems too high. The device must be oiled immediately when the shearing performance diminishes noticeably or the temperature of the clipping head seems too high. The clipping head should be oiled once per day when the clippers are not in use.

Replacing the clipping head:

The clipping head is a wear part. Despite good care, the cutting performance will diminish. At this point, the clipping head should be replaced. The clipping head can be ordered individually as a spare part (ref. no. 184604). When replacing the clipping head, you can remove the residue hair within the clippers using the brush. Press in the centre of the shearing blades to remove them (fig. 7). Place the new clipping head back onto the clippers as shown in fig. 8. Make sure that the locking mechanism is positioned properly and press the clipping head onto the device until it engages.

Cleaning the device:

Wipe off your device occasionally using a moist cloth, then rub it dry

Troubleshooting

What to do, when

the device cannot be switched on?

is the battery empty? Connect the power pack and charge the clippers
is the clipping head dry? The clipping head must be oiled

… the clipping head does not operate smoothly?

the clipping head must be oiled
the top and bottom blades can become stuck when not in use for longer periods of time

… the charging display does not light up when charging?

make sure that the power pack is connected properly

… the device switches off by itself?

the battery is empty. Charge the clippers

… the battery can no longer be charged?

the battery or the power pack is defective. The power pack can be re-ordered. If the battery is defective, then the device must be disposed of properly

Technical data

Clipper

Art. No: 184602
Motor speed: 5500/6000/6500 rpm
Charging time: 240 min
Shearing time: 240 min
Weight: 219 g
Input voltage :5V DC
Battery capacity: 2000 mAh
Ambient temperature charging process/use: 0°C – 40 °C
Protection class: III

Clipster, a brand of

Albert Kerbl GmbH
Felizenzell 9
84428 Buchbach, Germany
Tel. +49 8086 933 – 100
Fax +49 8086 933 – 500
info@kerbl.de
www.kerbl.de

Kerbl Austria Handels GmbH

Wirtschaftspark 1
9130 Poggersdorf
Tel. +43 4224 81555
Fax. +43 4224 81555-629
order@kerbl-austria.at
www.kerbl-austria.at

Kerbl France Sarl

3 rue Henri Rouby, B.P 46 Soultz
68501 Guebwiller Cedex, France
Tel. : +33 3 89 62 15 00
Fax : +33 3 89 83 04 46
info@kerbl-france.com
www.kerbl-france.com

Kerbl UK Ltd

Lands End Way
Oakham, Rutland
LE15 6RF, UK
Phone +44 01572 722558
Fax +44 01572 757614
E-Mail enquiries@kerbl.co.uk
www.kerbl.co.uk

Logo