ELLARD DM25LE Tubular Motor Instruction Manual

Tubular MotorDM25LE/L
Specification

(A-03)

Product introduction

**** One motor maximum can store 20 channels, over 20 channels, if still need to add new channels, it will be repeating covered the last channel.

Functional features：

• Electronic Limit
• Stall Protection
• Jog & Tilt
• Program Button
• Speed Regulation
• Memorized Setting
• Built-in Lithium Battery
• Switch Direction
• Built-in Receiver
• Preferred Stop Position
• Reset to Factor Mode
• DC Power
• Solar Charging

Parameter (More models and parameters are subject to the nameplate)

Type| Rated Torque

(N.m)

| Rated Speed

(r/min)

| Rated Current (A)| Rated Power

(W)

| Rated Voltage

(V)

| Emission Frequency(MHz)
---|---|---|---|---|---|---

DM25LE/L

| 0.7N| 34r| 1A| 8W| 8V| 433.92MHz
1.1N| 40r| 1A| 12W| 12V| 433.92MHz

Motor installation

1. Driving tube must be close-fitting with crown and drive adapter.
2. Choose crown and drive adapter based on the driving tube.

Charging instructions

**** The motor has a built-in battery,0.7nm motor uses DC782 charger to charge. You can also use solar panels DC683B to charge; when the battery is low, insert the charge, charger light shows red light. batteries are full when the red light turns green.

Operation note

**** Please read the following precautions before use:

1. Don’t operate motors when low voltage alarm：
   ①8V motor power supply voltage is below 6.8V when the motor stops running when the voltage is more than 7.5V to restart; When the power supply voltage is lower than 7.5V motor, the motor will call the alarm and the buzzer will call 10 times.
   ②12V motor power supply voltage is below 8.0V when the motor stops running when the voltage is more than 8.5V to restart; When the power supply voltage is lower than 7.0V when the motor stops the buzzer call when the voltage is greater than 7.5V before starting again; When the power the supply voltage is lower than 10V motor, the motor will call the alarm and the buzzer will call 10 times.

2. Operating：
   ①The valid interval of the emitter button is 10s, the emitter will quit the set after 10s.
   ②The motor will run or beep for the hint, please do the next step after the hint.

3. Set limit position：
   ①After the up/down limit position setting, the up/down limit position can’t be in the same position.
   ②After limit setting, with power off and memory function.
   ③Into the match-code status 2 minutes later, it will quit out the setting limits status automatically.
   ④It will delete every memory and restore the factory settings.

4. When the motor runs without any operation, the maximum running time is 6 minutes, it will stop automatically.

5. If the emitter is lost, please set it up again with the new emitter.

Button specification

1. Setting up
   P2→P2→Up
   If you need to reverse the rotation of the motor controlled by the emitter, please run the reverse direction setting(see the motor P1 button operation).
   Note: after the success of the code, remove the original travel setting and the speed of the motor operation mode, and restore the factory value.
   

2. Limit position setting
   1, Enter the limit position setting mode P2→Up→P2
   Note: This operation must be carried out without the limit; In the process of the motor running upward or downward, press the emitter setting button, and the motor enters the jog-move operation state, and can precisely set the limit position.
   2, Set the up limit position Up→Stop→Stop
   3, Set the down limit position Down→Stop→Stop
   Note: After the motor is powered off again, it will exit the trip setting mode; If you have not completed the limit, you will exit the setting mode of the limit, if you already have a limit, you will continue to use the pre-set limit; If the motor already has a limit, you need to delete the limit before you can set the limit.

3. Fine-tuning the up/down limit position setting
   Up+Down→Up/Down→Stop
   

4. Preferred stop position
   P2→Stop→Stop
   After the up limit and down limit setting, you can set the preferred stop position between them as the half-open position.
   Note: Continuous moving mode, long press stop button, the curtain run directly from the current position to preferred stop position(Apply to the shade); Jog-move mode, long press stop button, The motor will first run to the down limit position, then run to preferred stop position(Apply to Venetian blinds); Repeat this operation to remove preferred stop position.

5. Jog-move setting
   P2→Up→Down
   Note: Repeat this operation to cancel the dot-move function; In the jog- move mode, short press up/down button 2s to loosen, and the motor is jog-move to run; If long press more than 2s, the motor runs continuously.
   Add emitter
   Method one P2 →P2 →P2

Note: Emitter a   is the one that already matched the code, while emitter b has not; Repeat method one to remove the added emitter; After the success of the code retains the original motor and all the settings.

6. Delete all emitters
   P2→Stop→P2

7. Cancel limit
   P2→Down→P2

Note: This operation together with the preferred stop position to delete.

8. Speed Regulation
   1, Improve the speed of the motor Up+Stop

2, Reduce the motor running speed
Note: If the motor is without a run for the hint, indicating that the motor has reached the maximum or minimum value.

Motor P1 button operation

1, Short press operation

Note: This operation should be carried out under the conditions of motor has the limit.
2, Setting up or adding emitter

3, Shielding wireless function

Note: the motor enters the wireless shield mode, saves the previous system function setting and the emitter code, and closes the wireless reception function(short press P1 to restore wireless reception).
4, Switch direction

Note: After the success of the reversing, the motor limit remains the same.

Fault and solution

b, The emitter is not matched.
c, If press the P1 button for a long time while with no reaction. maybe the power is short-circuited or the circuit board or the motor is broken.| a, Activate the motor after fully charged
b, Set up the match code
c, Contact the engineers for after-sales

SAFETY NOTE

1. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by children without supervision.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its power source during cleaning, maintenance, and when replacing parts.
6. The instructions shall state that the A-weighted emission sound pressure level of the drive is equal to or less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
7. The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
10. Do not allow children to play with fixed controls. Keep remote controls away from children
11. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary
12. Watch the moving shutter and keep people away until the shutter is completely closed
13. WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
14. Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>