XELON AUDIO XA-M628B Car Multimedia Player User Manual
- June 1, 2024
- XELON AUDIO
Table of Contents
Car Multimedia Player
XA-M628B
USER MANUAL
XA-M628B Car Multimedia Player
WARNING
-
Only connect the unit to a DC 12V power supply with negative grounding.
If you connected to the car of 24V, it’ll be burned. (Note: Only the panel label with 24V,then it can be used in the car of 24V power supply.) -
When the machine is in a state of abnormal during the operation, you need to use a pointed object to press the key of “RES”(on the panel), then it will be reset and in factory state .
-
Never install the unit where the operation for safety driving is restrained.
-
Never use the video display function in the front when driving to prevent the violation of laws regulation and also to reduce the risk of traffic accident except using for rear view video camera .
-
Never expose the unit, amplifier, speakers to moisture or water to prevent electronic sparks or fires .
-
Please do not change the fuse in the power cord without professional guidance; improper fuse may cause damage to this using unit or even cause fire .
-
When the temperature is too high or too low in the car, please adjust the temperature firstly, and then use this machine .
Precautions
- When the interior of the car is extremely cold and the unit is used soon after switching on the heater, moisture may form on the optical parts of the player and proper playback may not be possible. If moisture forms, wipe it off with a soft cloth. If moisture forms on the optical parts of the unit, do not use the unit for about one hour. The condensation will disappear naturally allowing normal operation.
- Driving on extremely bumpy or rough roads can cause the unit to skip during playback.
- This unit uses precision parts and components for its operation. In the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Contact your service center
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance between 20cm the radiator your body.
Installation
Please have it professionally installed and refer to the following diagram description:
- Please install the unit in a proper place, connect the unit and refer to the diagram, and test it to make sure it works well or not.
- Please wrap the connection wires with insulation tape to ensure complete wiring after testing well .
- Please bend the hook of metal 1, and insert the metal to instrument panel then install it.
- Put the unit into metal hook unit to lock it.
General Features
6.5″ Double-Din Touch Screen Receiver
- 6.5 Inch Double din Touch Screen Receiver
- High Resolution
- 1080P Video Format
- Supports Audio in a Variety of Formats
- Supports Video in a Variety of Formats
- MOSFET Amplifier: 60 Watts X 4 MAX POWER OUTPUT
- FM Range: 87.5MHz~107.9MHz
- With Remote Control
- Power-off with auto-memory unction
- Clock Function
- Mute Function
- Wireless Streaming Functions
- Aux In Function
- Rearview Camera Function
- Video input Function
Wiring- Back Panel:
Please check the speaker line carefully before installation. Ifany grounding or touching, please connection again, otherwise the unit will be burned.
General Operation
- When use reversing rear view function, reversing video signal from the corresponding port input connection back line, when reversing will automatically switch to reversing visual state .
- Audio / Video input (Optional)Connect Audio / Video lines, press Mode can select AUX-2 state.
- Operation of Wireless Streaming Function
First, open the Wireless Connectivity function on your phone, and then find the name of the model and pair your device using the password “0000”, after your device has been paired successfully, the symbol will turn green. When calls come in, it will automatically connect, press to answer the phone, and press to decline/hang up the phone.
Troubleshooting
- ftheunitcouldntbootup .pleasecheckwhethertheconnectionofthe powerof positiveand negative is right ,ontheotherhand ,checkwhethe the fuse is burned .ltmaybebettertosendusphotos toshow inorder tosolve the problem
- Black screenorshutdownautomatically. Itmayhave lostthe software ,so please check thedateofproductionon thepkboard .wecanprovide the right software to updateafterweknowthedate ofproduction
- Nosound .checkwiringdiagram ,makesure the connection is right.
- The button doesn’t work. Check whether the keys are stuck.
- The radiodoesn’twork.checkwhether theconnectionofrtheadioantenna is correct:
- searchstation automaticallyandcouldn’tstop .The loca Iradiosigna maybe too weak. Try searching for the station manually.
systematicparameter
specifications workingvoltage: directcurrent12v workingvoltage range: 10.8v-
16v Maximum working electroniccurrent :10A
Installation angle: less than 30 degree tiltedthe front sideand backside
Max Power output: 4X60 W impedance 4ohm SNR: 70dBA Frequency Response : 20HZ-
20KHZ
video Standards: NTSC. PAL (Auto recognition) Output 1 Vp-p(75ohm) Input:
1Vp-p(75ohrn)
FM Radio
Frequencymodulation
87.5MHZ ～107.9MHZ
Flexibility(-30dB):10dBU
SNR(-50dB):15dBU
Frequent sound range
30H2~15KHz (+3dB)
Display
Screen type: TFT
Response time: up=50 millisecond.
Down=50 millisecond
Angle range: depression angle=65
elevation angle=40 <>
Left vision=65 right vision =65
Environment temperature
Operation temperature:-20~+ 70°C
Maintenance temperature: -30°C~80°C
Operating humidity:45% ~ +80%6°C (relative humidity)
Maintenance humidity:30%~90% (relative humidity)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>