ELLARD DM25LEU 25mm Bidirectional Motor Instructions

DM25LEU/S
Instruction A-04

Features

• Built-in Receiver
• Jog & Tilt
• Built-in Lithium Battery
• Scan and Program
• Status Feedback| • Switch Direction
• Stall Protection
• Program Button
• Reset to Factory Mode
• Memorized Setting| • Electronic Limit
• Preferred Stop Position
• Speed Regulation
• Scene Control
---|---|---

Fields of Application

The motor is suitable for the motorization of roller blinds.

Specifications

Following data for reference

***** For reference only.

Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in the right position as follows.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void the manufacturer’s liability and warranty.

Charging Instructions

This motor has a built-in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before the first use please charge the motor for 6 hours. Using a 5V charger (most phones charger are 5V ).
During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, and the battery stopped running and needed to be recharged.

Rechargeable Battery

Motor Installation

Step 3 Mount the correct crown & drive adapter on the motor. Make sure the drive adapter fits firmly and the crown rotates freely.
Step 4 Align the notches on the crown and drive adapter with the drive tube, slide and fit the motor into the drive tube. Mount idler and bracket on both ends.

Caution

1. Do not expose the motor to humid, damp, or extreme temperature conditions.
2. Do not drill into the motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use it.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure power cable and aerial are clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. The motor is to be mounted in a horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside the scope of this instruction may void the warranty.

Important Safety Instructions To Be Read Prior To Operation.

Setting Notice
Please read the following points of attention carefully before setting.

1. Don’t operate motors when low voltage alarm.

2. Operating ：
   ①The valid interval of the emitter button is 10S, the emitter will quit the set after 10S.
   ②The motor will run or beep for the hint, please do the next step after the hint.

3. Set the limit position ：
   ①After the upper / lower limit setting and the upper/lower limit position can’t be in the same position.
   ②After the limit setting, with power off and memory function.
   ③Limit delete will clear all limited memory.
   ④It will exit the limit set when the program there is not operating for 2 minutes.

4. If the emitter is lost, please set it up again with the new emitter.

5. One motor can store a maximum of 10 channels; after fully storing, if pair new channels, only the last one will be covered circularly.

Button Instructions

*Dial lithium battery switch, 0 is off switch, 1 is turn on the switch.
Functions of the P1 button

1. Cycle Operation： Press the P1 button once and with every press, the motor will run upward → and stop → downward circular.
2. Pairing or Pair Additional Emitter： Press the P1 button for 2S, motor jog once, release the button and make a long noise, motor is ready for pairing or pair additional emitter.
3. Radio Lock: Press and hold the P1 button for 6S, the motor will jog twice, release the button, and beep twice, the motor enters radio lock status, but the motor won’t receive any signal; press the P1 button once to disable Radio Lock.
4. Switch Direction: Press and hold the P1 button for 10S, the motor will jog 3 times, release the button, and beep 3 times, the running direction of the motor has been changed.
5. Reset to Factory Mode: Press and hold the P1 button for 14S, the motor will jog 4 times, release the button and beep 4 times, the motor has been reset to factory mode. At this point, the motor will go into a deep sleep. After entering deep sleep, the motor can’t be controlled. At this time, you need to press the P1 button for 2S and then the motor turns to prompt you to exit deep sleep.

Essential Settings
The steps in factory mode must be completed to ensure proper operation.

Factory mode

1 Pairing

| Press the P1 button for 2S (1 jog ), release the button and make a long nose, Or turn the DIP switch to “0” and then to “1” (1 jog and make a long nose), repower the motor, within 10S, press STOP for 2S (2 jogs and 3 beeps ), the motor has been paired successfully.
---|---

***** If within 10S, the motor doesn’t receive a STOP signal from any emitter, it will exit the pairing mode automatically.
Re-power on after power off, if the motor has saved the emitter, there is no rotation prompt, and the code matching status is not automatically entered at this time.

2 Switch Rotating Direction (Optional)
If press UP, the motor runs downward, try below to switch direction

| Press and hold UP and DOWN buttons simultaneously for 2S, motor jog once, and the direction has been switched successfully.
---|---

*The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch directions by the P1 button.

3 Upper and Lower Limits Setting

1 Set upper limit
| 2 Set lower limit

---|---
Press UP for 2S, operate the motor to the desired upper position, press and hold UP and STOP buttons simultaneously for 2S (2 jogs and 3 beeps), and the upper limit is set.| Press DOWN for 2S, operate the motor to desired lower position, press and hold DOWN and STOP buttons simultaneously for 2S (2 jogs and 3 beeps), and the lower limit is set.

*If exit the limits setting status before you finish the limit setting, then the motor will take the previous limits if has; After the limits have been set successfully, the motor will enter the user mode.

User mode

1 Add A Preferred Position

1 Set preferred position
| 2 Remove preferred position

---|---
Check both upper and lower limits are set. Operate the product to the desired preferred position. Press P2 (1 jog and 1 beep), press STOP(1 jog and 1 beep), STOP again (2 jogs and 3 beeps), and the preferred position is set.| Press P2 (1 jog and 1 beep), press STOP (1 jog and 1 beep), STOP again(1 jog and make a long nose), and the preferred position is deleted.

*Press STOP for 2S, and the motor moves to the preferred position automatically.

2 Jog Mode & Running Mode Switch

| Press and hold UP and DOWN buttons simultaneously for 5S (1 jog), press STOP (1 jog and make a long nose), and switch to jog mode, If the motor jog twice and beeps 3 times, switch to running mode.
---|---

*when in jog mode, press UP or DOWN once, and the motor will be jog running, if pressed for more than 2 seconds, the motor will be continuously running.

3 Adjust Limits
1 Adjusting the upper limit

Press and hold UP and STOP buttons for 5S (1 jog and make a long nose), operate the product to desired new upper limit position, press and hold UP and STOP buttons for 2S(2 jogs and 3 beeps), and the new upper limit is programmed successfully.

2 Adjusting the lower limit

Press and hold DOWN and STOP buttons for 5S (1 jog and make a long nose), operate the product to the desired new lower limit position, press and hold DOWN and STOP buttons for 2S (2 jogs and 3 beeps), and the new lower limit is programmed successfully.
*After entering the limits fine-tuning mode, the original preferred position will not be deleted; If there is no button operation within 2 minutes, it will arrive within 2 minutes, and the motor will turn to prompt, and automatically exit the route adjustment mode; When fine-tuning the limit, press, and P1 for more than 2S to exit the mode.

4 Pair / Unpair Additional Emitter

Method one

Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on the existing emitter, press P2 on the new emitter to add (2 jogs and 3 beeps), and the new emitter is paired to the motor.
• Repeat same procedure will unpair additional emitter.

Method two

| Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep and 1 beep) on the existing emitter, press STOP on the new emitter for 2S to add (2 jogs and 3 beeps), the new emitter is paired to the motor.
---|---
| Press the P1 button for 2S (1 jog), release the button and make a long noise, press STOP on the new emitter for 2S to add (2 jogs and 3 beeps), and the new emitter is paired to the motor.
• Repeat same procedure will unpair additional emitter.

*(a) as existing emitter,(b) as new emitter to pair/unpair; Adding the emitter should be carried out when there is a limit;
All the settings of the motor will be kept after adding the new emitter.

5 Speed Regulation
1 Acceleration setting

| Press P2 (1 jog and 1 beep), UP (1 jog and 1 beep), UP again (2 jogs and 1 beep), and the motor running speed is accelerated.
---|---
| Press P2 (1 jog and 1 beep), DOWN (1 jog and 1 beep), DOWN again (2 jogs and 1 beep), and the motor running speed is decelerated.

*If the motor has no response, it has already been the Max. or Min speed.

Quick Index

|

Settings

|

Steps

---|---|---
1| Pairing| P1 (hold down 2s) → Stop (hold down 2s)
2| Switch Rotating Direction| Up + Down (hold down 2s)

3

|

Upper and Lower Limits Setting

| Set upper limit| Up (hold down 2s) → Up + Stop (hold down 2s)
Set lower limit| Down (hold down 2s) → Down + Stop (hold down 2s)
4| Add / Remove Preferred Position| P2 → Stop → Stop
5| Jog Mode & Running Mode Switch|

Up + Down (hold down 5s) → Stop

6| Adjust Limits| Adjusting the upper limit| Up + Stop (hold down 5s) → Up or Down → Up + Stop (hold down 2s)
Adjusting the lower limit| Down + Stop (hold down 5s) → Up or Down → Down + Stop (hold down 2s)
7| Pair / Unpair Additional Emitter| P2(a) → P2 (a) → P2(b)
P2(a) → P2 (a) → Stop (b) (hold down 2s)
P1 (hold down 2s) → Stop (b) (hold down 2s)
8| Speed Regulation| Acceleration setting| P2 → Up → Up
Deceleration setting| P2 → Down → Down

Troubleshooting

Issues

| Possible causes|

Solution

---|---|---
The motor has no response| The battery in the motor is depleted| Recharge with compatible AC adaptor
Power Failure Or Incorrect Connection| Double-check power and cable connections, and follow wiring instructions.
emitter battery is low capacity| Replace battery
Radio interference/shielding| Check antenna on the motor is intact and exposed. Check for the possible sources of radio interference.
Out of radio control range| Try control within a closer range
The emitter can’t control single motor|

Multiple motors are paired to the same channel.

| Pair single motor with emitter correctly
Try to use multi-channel emitters to control multi-motor projects, and ensure each channel controls one single motor
The motor doesn’t run or start too slowly or make a loud noise| Connections are incorrect.| Check connections
Installation is improper or overload| Check installation or overload
The motor stops during the up and down running| The motor has reached the lower limit| Adjust the new lower limit
The running time was more than 6min| Consult the sales for more information

SAFETY NOTE

1. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by children without supervision.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its power source during cleaning, maintenance, and when replacing parts.
6. The instructions shall state that the A-weighted emission sound pressure level of the drive is equal to or less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
7. The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
10. Do not allow children to play with fixed controls. Keep remote controls away from children.
11. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary.
12. Watch the moving shutter and keep people away until the shutter is completely closed.
13. WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
14. Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation.

Do not dispose of general waste.
Please recycle batteries and damaged electrical products appropriately.

References

• Die Welt der Mode | Mode.at

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>