ELLARD DM35 Tubular Motor Instructions

DM35(45)F/Y
Instruction A-03

Features

• Built-in Receiver
• Precise Limit Setting
• Jog & Tilt
• Limit Fine Adjustment| • Switch Direction
• Stall Protection
• Program Button
• Reset to Factory Mode| • Electronic Limit
• Preferred Stop Position
• Sun-sensor Compatible
---|---|---

Fields of Application

The motor is suitable for the motorization of roller blinds, and awnings.

Specifications

time: > 4 minutes

Following data for reference

Rated Voltage (V)| Model| Rated Torque (N.m)| Rated Speed (rpm)
---|---|---|---
230| DM35F/Y-6/28| 6| 28
DM35FN-10/17| 10| 17
DM35FN-13/14| 13| 14
DM45FN-10/15| 10| 15
DM45FN-10/26| 10| 26
DM45FN-20/15| 20| 15
DM45F/Y-20/26| 20| 26
220| DM35FN-10/21| 10| 21
120| DM35F/Y-6/33| 6| 33
DM35FN-10/21| 10| 21
DM45FN-10/19| 10| 19
DM45FN-10/32| 10| 32
DM45FN-20/19| 20| 19
DM45F/Y-20/32| 20| 32

• For reference only.

Attention
Never drop, knock, drill or submerge the motor. Keep the power cable in the right position as follows.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void the manufacturer’s liability and warranty.

Wiring
Five lines: AC 230V/50Hz, AC 220V/60Hz, AC 120V/60Hz

Motor Installation

|
---|---
Step 1 Cut the drive tube to the required length.| Step 2 Ensure the tube edge is clean and burr-free.
|
Step 3 Mount the correct crown & drive adapter on the motor. Make sure the drive adapter fits firmly and the crown rotates freely.| Step 4 Align the notches on the crown and drive adapter with the drive tube, slide and fit the motor into the drive tube. Mount idler and bracket on both
ends.

Caution

1. Do not expose the motor to humid or extreme temperature conditions.
2. Do not drill into the motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use it.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure power cable and aerial are clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. The motor is to be mounted in a horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming to be performed by a qualified professional, use, or modification outside the scope of this instruction may void the warranty.

Important Safety Instructions To Be Read Prior To Operation.

Setting Notice
Please read the following points of attention carefully before setting.

1. Please use accessories kits to protect the wires which are not used.

2. Operating ：
   ① The valid interval of the emitter button is 6s, the emitter will quit the set after 6s.
   ② The motor will jog or beep for the hint, please do the next step after the hint.

3. Set limit position ：
   ① After the upper/lower limit setting and the upper/lower limit position can’t be in the same position.
   ② After limit setting, with power off and memory function.
   ③ Limit delete will clear all limit memory.
   ④ It will exit the limit set when the program there is not operating for 2 minutes.

4. If the emitter is lost, no limit case, please set it up again with a new emitter; Have a limit case, please add the emitter again with the new emitter, the limit remains the same.

5. One motor can store a maximum of 20 channels; after fully storing, if pair new channels, only the last one will be covered circularly.

Button Instructions

Functions of PROG button

1. Pairing or Pair Additional Emitter: Press the PROG button for 2S, the motor beeps 3 times, and the motor is ready for pairing or pairing additional emitter.
2. Switch Direction: Press and hold the PROG button for 5S, motor beeps 3 times and jogs once, release button, motor running direction is switched.
3. Reset Motor: Press and hold the PROG button for 10S, motor beeps 3 times and jog once, release button, motor jog once. All motor settings are reset.

Essential Settings
Steps 1 to 3 must be completed to ensure proper operation.

Pairing

Power on the motor (3 beeps for the code, if the code is not aligned, make a long noise and 1 jog), within 10S, press P2 (1 beep and 1 jog ), P2 again (1 beep and 1 jog), and UP (3 beeps and 1 jog), the motor is paired with the emitter.

Switch Rotating Direction (Optional)
Press UP and the motor runs downwards, try below to switch directions.

Press and hold UP and DOWN buttons simultaneously for 2S (3 beeps and 1 jog), the direction has been switched successfully.

• The motor needs to be in the reversing operation without limit.

Setting Upper and Lower Limits

1 Initiate limit setting| | Press P2 (1 beep and 1 jog), UP (1 beep and 1 jog), and P2
(3 beeps and 1 jog), the motor is ready for limit settings.
---|---|---
2 Set upper limit| | Press UP, operate the motor to the desired upper position, press
STOP once, then press and hold STOP for 5S (3 beeps and
1 jog), the upper limit is set.
3 Set lower limit| | Press DOWN, operate the motor to a desired lower position, press STOP once, then press and hold STOP for 5S (3 beeps and 1 jog), the lower limit is set.

• When there is no limit, the limit can be set without entering the limit setting mode.

Add A Preferred Position

1. Set preferred position(Within the limits)Check both upper and lower limits are set. Operate the product to the desired preferred position. Press STOP once, then press P2 (1 beep and 1 jog), STOP (1 beep and 1 jog), STOP again (3 beeps and 3 jogs), the preferred position in the limits is set.
2. Set preferred position(Outside the lower limit)Check both upper and lower limits are set. Press P2 (1 beep and 1 jog), DOWN (1 beep and 1 jog), DOWN again (3 beeps and 1 jog), then press UP or DOWN, operate the product to the desired preferred position, press P2 (1 beep and 1 jog), STOP (1 beep and 1 jog), STOP again (3 beeps and 3 jogs), preferred position setting outside the lower limit is ok.

• If the motor has a preferred position within the limits, you need to delete the preferred position before setting. 3. Run to the preferred position
  Press STOP for 2S and the motor will automatically run to the preferred position.

  4. Remove preferred position
     Press P2 (1 beep and 1 jog), STOP (1 beep and 1 jog), STOP again (make a long noise and 1 jog), and the preferred position is deleted.

Adjust Limits

1. Adjusting the upper limit positionOperate product to the upper limit position. Press and hold UP and DOWN buttons simultaneously for 5S (3 beeps and 1 jog), operate the product to the desired new upper limit position, then press and hold UP and DOWN buttons simultaneously for 5S (3 beeps and 1 jog), the new upper limit is programmed successfully.
2. Adjusting the lower limit positionOperate product to the lower limit position. Press and hold UP and DOWN buttons simultaneously for 5S (3 beeps and 1 jog), operate the product to the desired new lower limit position, then press and hold UP and DOWN buttons simultaneously for 5S (3 beeps and 1 jog), the new lower limit is programmed successfully.

Activate / Deactivate Jog / Tilt Mode

Press P2 (1 beep and 1 jog), UP (1 beep and 1 jog), and DOWN (long sound 1 and 1 jog), Jog/tilt mode is deactivated.
If the motor beeps 3 times and jogs 3 times, the Jog/tilt mode is activated.

• When under jog mode, press UP or DOWN for 2S, and the motor will be continuously running.

Pair / Unpair Additional Emitter

Press P2 (motor beep and jog once) and P2 (1 beep and 1 jog) on the existing emitter, press P2 on the new emitter to add (3 beeps and 1 jog), and the new emitter is paired to the motor.

• Repeat the same procedure will unpair additional emitter.

• (a) as existing emitter, (b) as new emitter to pair/unpair.

Remove All Emitters Press P2 (1 beep and 1 jog), STOP (1 beep and 1 jog), and P2 (3 beeps and 1 jog), all emitters are deleted.

Deleting All Limits Press P2 (1 beep and 1 jog), DOWN (1 beep and 1 jog), and P2 (3 beeps and 1 jog ), all limits are removed.

Enable / Disable Power-on to Pair Function Press P2 (1 beep and 1 jog), UP (1 beep and 1 jog), UP again (long sound 1 and 1 jog), and the motor turns off power-on to pair function. If the motor beeps 3 times and 3 jogs, the motor turn on power-on to pair function.

• The factory default mode is ON.

Enable / Disable Power-on Prompting Function Press P2 (1 beep and 1 jog), UP (1 beep and 1 jog), STOP (long sound 1 and 1 jog), and the motor turns off the power-on prompting function. If the motor beeps 3 times and 3 jogs, the motor turn on the power-on prompting function.

• The factory default mode is ON.

Enable / Disable Sensitive Stall Detection

Press P2 (1 beep and 1 jog), press UP and STOP simultaneously (1 beep and 1 jog), press UP and STOP simultaneously again (long sound 1 and 1 jog), and the motor turns off sensitive stall detection. If the motor beeps 3 times and 3 jogs, the motor turn on sensitive stall detection.

• The factory default mode is ON.

Pair With Wind-sun Sensor For Awning.

Adding Wind-sun Sensor

Use paired emitter, press P2 twice (motor beep and jog on each press), press P2 on the wind-sun sensor (3 beeps and 1 jog), and the wind-sun sensor is paired to the motor.

• (a) as an existing emitter, (b) as a sensor to pair/unpair. Add multiple wind-sun sensors only currently valid, others are covered.

Enable / Disable Sun Detection

1. Enable sun detection Press UP and STOP buttons simultaneously (3 beeps and 3 jogs), Sun detection is enabled.
2. Disable sun detection Press DOWN and STOP simultaneously (long sound 1 and 1 jog), Sun detection is disabled.

Quick Index

| Settings| Steps
---|---|---
1| Pairing| P2 → P2 → Up
2| Switch Rotating Direction| Up + Down (hold down 2s)
3| Upper and Lower Limits Setting| Initiate limit setting| P2 → Up → P2
Set upper limit| Up → Stop → Stop (HDD down 5s)
Set lower limit| Down → Stop → Stop (HDD down 5s)
4| Add / Remove Preferred Position| Set preferred position( Within the limits)| Up or Down → Stop → P2 → Stop → Stop
Set preferred position(Outside the lower limit)| P2 → Down → Down → Up or Down → P2→ Stop → Stop
Run to the preferred position| Stop (hold down 2s)
Remove preferred position| P2 → Stop → Stop
5| Adjust Limits| Adjusting the upper limit position| Up → Up + Down (hold down 5s) → Up or Down → Stop (hold down 5s)
Adjusting the lower limit position| Down → Up + Down (hold down 5s) → Up or Down → Stop (hold down 5s)
6| Activate / Deactivate Jog / Tilt Mode| P2→Up →Down
7| Pair! Unpair Additional Emitter| P2(a) → P2 (a) → P2(b)
8| Remove All Emitters| P2 → Stop → P2
9| Delete AI Limits| P2 → Down → P2
10| Enable! Disable Power-on to Pair Function| P2 → Up → Up
11| Enable! Disable Power-on Prompting Function| P2 → Up → Stop
12| Enable / Disable Sensitive Stall Detection| P2 → Up + Down → Up + Down
13| Adding Wind-sun Sensor| P2(a) → P2 (a) → P2 (wind* sun sensor)
14| Enable! Disable Sun Detection| Enable sun detection| Up + Stop
Disable sun detection| Down + Stop

Troubleshooting

check power and cable connections, follow the wiring
instructions.
The battery in the emitter is low| Replace battery
Radio interference/shielding| Check antenna on the motor is intact and exposed. Check for the possible source of radio interference.
Out of radio control range| Try control within a closer range
Cannot program a single Motor (multiple motors respond)| Multiple motors are paired to the same channel.| Always reserve an individual correctly (refer to motor functions)
SYSTEM BEST PRACTICE – Provide an extra 15 channel controller in your multi- motor projects, that provides individual control for each motor for programming purposes
The motor does not raise or lower the blinds or shutters, starts too slowly, or makes a loud noise.| Connections are incorrect.| Check connections
Incorrect installation or overload| Check installation or overload
The motor stops during the going up or going down.| Down limit is reached| Set a new down limit
Running time exceeds 4 min| Let the motor cool for about 20 min

SAFETY NOTE

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by children without supervision.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its power source during cleaning, maintenance, and when replacing parts.
6. The instructions shall status that the A-weighted emis sion sound pressure level of the drive is equal to or less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
7. The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
10. Do not allow children to play with fixed controls. Keep remote controls away from children.
11. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary.
12. Watch the moving shutter and keep people away until the shutter is completely closed.
13. WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
14. Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>