Avantree HT5006 Wireless Earbuds for TV Listening, Passthrough Support, 20Hrs Neckband Headphones-Complete Features/User Instruction

Avantree HT5006 Wireless Earbuds for TV Listening, Passthrough Support,

20Hrs Neckband Headphones

Specifications

• BRAND: Avantree
• CONNECTIVITY TECHNOLOGY: Wireless, Wired
• FORM FACTOR: Over-Ear
• HEADPHONES JACK: RCA
• CABLE FEATURE: Without Cable
• HARDWARE PLATFORM: ‎ Tablet
• AVERAGE BATTERY LIFE (IN HOURS): ‎40 Hours

Introduction

Headphones produce high-quality sound in perfect synchronization, making them ideal for watching TV, movies, and gaming. Dual link technology on the transmitter allows you to add a second set of headphones (AS9) to share the listening experience. Simply turn on the Bluetooth transmitter and headphones and they will instantly pair for a genuinely plug-and-play experience. There’s no need to be concerned about difficult instructions. It can be difficult to connect new gadgets when your TV just has one optical out port. You can connect the Avantree Oasis Plus (TX) to your sound bar and TV to simultaneously play audio from the soundbar and stream to headphones!

Our Oasis Plus (TX) transmitter signal has a range of up to 164 feet / 50 meters thanks to Bluetooth Class I technology! Please keep in mind that the range is limited by physical obstacles and wireless interference. It suits your needs whether you use the Avantree transmitter with another Bluetooth receiver to enhance your TV watching experience or couple the headset (AS9S) with your smartphone or tablet.

WHAT’S IN THE BOX

1. AS9S BT Headphones
2. Oasis Plus BT Transmitter
3. Optical Audio Cable
4. 5mm Audio Cable
5. 5mm to RCA Audio Cable
6. Micro USB Power Cable*2

PRODUCTS OVERVIEW

LED INDICATION & VOICE PROMPTS

LED INDICATORS OF THE TRANSMITTER (OASIS PLUS)

LED INDICTORS & VOICE PROMPTS OF HEADPHONES (AS9S)

Charging/Charging

completed

| RED LED on/off| NA
Low battery| RED LED flashes| Low battery

TURN ON HT5009

POWERING UP THE TRANSMITTER
Power up the transmitter with the USB cable provided. Connect it to a TV USB port (TV needs to be turned on) or any other USB charger that supports 5V /500mA-2A.

TURN ON BOTH DEVICES

• Turn on the transmitter – Slide Mode switch to the “TX” position, and the “TX” LED will start flashing WHITE.

• Turn on the headphone – Press and hold the call button for 2 seconds until you see the BLUE LED light.

• They will auto-reconnect, indicators are: 1) Headphones say” Welcome to Avantree. Connected”. 2) Transmitter says “Connected. Ready for use.” The “TX” LED will stop flashing and “A” LED will light up.

USE HT5009 WITH YOUR TV

Check your TVs output options before the setup

TVS WITH OPTICAL AUDIO OUT

Now you should be able to use the headphone. IF there’s no sound:

Ensure the transmitter LED “OPT” is on. If not, short press the AUX OPT button once.

1. Ensure your TV speaker is set to “External Speaker”.
2. Ensure TV Audio Format is set to “PCM” or “DOLBY/DTS” is off (This is IMPORTANT).

TVS WITH AUX/3.5MM AUDIO OUT

1. Make sure the “AUX” LED is on. If not, short press the AUX OPT button once to select AUX audio.
2. Now, you should be able to use the headphone. If no sound, please ensure your TV speaker is set to “Headset”

TVS WITH RCA AUDIO OUT (RED/WHITE PORTS LABELED “AUDIO OUT”)

Now you should be able to use the headphones. If no sound:

1. Make sure the “AUX” LED is on, if not, short press the AUX OPT button once to select AUX audio.
2. Make sure you’ve used the TV Red/White ports labeled “AUDIO OUT.” Other Red/White ports will NOT work.
3. Ensure your TV speaker is set to “External Speaker”

USE HT5009 WITH YOUR AV RECEIVER WITH A 6.35MM PHONE JACK

Make sure the “AUX” LED is on, if not, short press the AUX OPT button once to select AUX audio.

NOTES

Please do NOT use the RCA ports on the back of your AV receiver. They will not work and may permanently damage the transmitter.

• ONLY use the BIG 6.35MM PHONE OUT located in the FRONT of your AV Receiver with the 6.35mm to 3.5mm adapter (not included).
• Do NOT set the volume too high.
• You may test the port with wired headphones before using it.

USE THE HEADPHONES INDEPENDENTLY WITH A CELLPHONE

• STEP 1: Ensure the transmitter is off.
• STEP 2: Enter the headphones into PAIRING MODE – from its OFF state, press and hold the CALL button for 5 seconds until the LED flashes RED and BLUE alternately, and you hear“Pairing” from the headphones.
• STEP 3: Turn on Bluetooth on your Bluetooth-enabled device. Find & select “Avantree AS9S” to pair and connect. The next time, you would like to use your headphones this way you will need to select “Avantree AS9S” on your Bluetooth-enabled device to reconnect.

ADD A 2ND PAIR OF BLUETOOTH HEADPHONES

NOTE
Since Oasis Plus doesn’t support dual-link aptX HD, we suggest that you switch to the “LL” position to get more stable connections during dual link.

• STEP 1: Turn on the transmitter and AS9S headphones.

• STEP 2: Enter the transmitter into the PAIRING MODE manually – press and hold the BLUETOOTH button for 2 seconds, “TX” LED will start flashing GREEN and WHITE alternately.

• STEP 3: Place your 2nd set of headphones into Bluetooth PAIRING MODE (Please refer to your 2nd headphone’s user manual).

• STEP 4: Keep the devices close to each other and wait. Once connected. You will hear the voice prompt “Connected. Ready for use.” Once succeeded, you will find LEDs A and B to both be lit.

For Next Use, please turn on AS9S headphones first, both headphones will auto- reconnect to the transmitter once turned on. If turn on AS9S later, please press the CALL button once to reconnect.

CHARGING HEADPHONES

Please charge the headphone if you hear the “low battery” voice prompt. You may charge using a phone charger (5V/500mA-2A output,) a PC USB port, a TV USB port, or any other USB outlet using the USB cable provided in the box. It takes about 3.5 hours to fully charge the headphone. The LED will turn RED while charging and will turn off automatically once the charging is complete.

CLEAR PAIRING HISTORY

CLEAR PAIRED HISTORY OF THE TRANSMITTER:
Press and hold the + and – buttons together for 7 sec until you hear the voice prompt “Pairing history cleared”, Right after that, the Green and White LEDs will flash rapidly together, indicating Oasis Plus entering pairing mode again. TX history is cleared.

CLEAR PAIRED HISTORY OF THE HEADPHONES
After turning on, press and hold both “+” and”-“ for 10 seconds until the LED turns PINK – now the pairing history of the headphone has been cleared, it will enter pairing mode automatically with the LED flashing alternately RED and BLUE.

Frequently Asked Questions

• What’s the best way to set up a Marshall Uxbridge speaker?
  For 2 seconds, press and hold the Bluetooth button. While in pairing mode, the front indicators change to a slow blinking blue.
  Turn on Bluetooth on your phone or tablet (smartphone, tablet, and computer).
  Accept pairing by selecting Uxbridge from the Bluetooth list.

• Is Marshall Uxbridge a good investment?
  The Marshall Uxbridge Voice is well worth the money if you want a smart speaker that sounds well and doesn’t take up too much space on your bookshelf. As long as you’re already in the Amazon ecosystem, the classic amp design and sound quality make it a terrific value.

• What is the procedure for resetting Marshall Uxbridge?
  A factory reset is also an option. NOTE: This will remove all user settings, and the speaker will need to be set up a new following the factory reset. For 7 seconds, press and hold the upper portion of the volume (+) and the lower half of the treble button (-).

• What is the best way to connect my Marshall Speaker to Wi-Fi?
  Choose Wi-Fi as your input. To make the speaker discoverable, press and hold the Source button for 3 seconds. The mobile device and the speaker are not on the same Wi-Fi network. Make sure your smartphone or tablet is connected to the same Wi-Fi network as the speaker.

• Is there a microphone on the Marshall speaker?
  In terms of limitations, this speaker lacks a microphone, so if your phone is linked through Bluetooth, you’ll have to disconnect it to take calls. That also means Emberton lacks support for voice assistants, which may or may not be a problem for you.

• Is it possible to connect Marshall speakers to Alexa?
  You can use Alexa to play music, listen to the news, check the weather, and operate smart home gadgets, among other things. To enable Alexa on your Stanmore II Voice, sign in to Amazon Alexa through the Marshall Voice App. Say Alexa or press the microphone button to activate Alexa.

• Is it possible to use a Marshall speaker with Alexa?
  Uxbridge Voice blends Marshall’s iconic sound with Amazon Alexa’s helpfulness to create a speaker that is not only smart but intelligent. This speaker is small in size yet big on sound, providing a clear and precise audio experience. Alexa allows you to multitask while remaining hands-free.

• What is the procedure for canceling my Marshall Uxbridge?
  It can only be turned off by unplugging it. Marshall’s decision to keep the speaker on at all times, with Alexa (or Google) on standby is undoubtedly deliberate (more on Alexa below). On that note, the Uxbridge is not intended to be portable because it requires electricity from the mains.

• Is it possible to connect a Marshall speaker to a television?
  Yes, if your TV has Bluetooth, RCA, or 3.5 mm auxiliary outputs, the Stanmore Bluetooth Speaker can connect to it. Any lag that may occur with wireless connections will be minimized if you connect by cable.

• What is the procedure for turning on my Marshall speaker?
  Connect the power cord to the speaker’s power jack on the back. 3. Turn the on/off switch to the ON position to activate the active loudspeaker.

https://www.manualslib.com/manual/1599964/Avantree-Ht5009.html?page=2#manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>