meitav-tec FMH24-PD-1S-IR Thermostat Owner’s Manual
- June 10, 2024
- meitav-tec
Table of Contents
- meitav-tec FMH24-PD-1S-IR Thermostat
- FMH24-PD-1S-IR Product Information
- Installation Instructions
- General Points to Follow
- Wiring Connections
- Switching the Thermostat On
- Switching the Thermostat Off
- Setting the Temperature
- Selecting Modes
- FMH24-PD-1S-IR
- Overview
- Product Wiring Connections
- Operating Manual
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
meitav-tec FMH24-PD-1S-IR Thermostat
FMH24-PD-1S-IR Product Information
The FMH24-PD-1S-IR is a Flush Mount unit thermostat manufactured by Meditate Ltd (Comtel group). It is a temperature control device that can be used to regulate heating, cooling, or fan-only systems. The device is designed to provide an accurate reading of the temperature and can be installed easily in an electrical box.
Installation Instructions
It is important to find the right place to install the Flush Mount unit. Please make sure to follow all the installation instructions in order to get an accurate reading of the temperature.
General Points to Follow
- Connect the wires (see #2)
- Put the thermostat in the electrical box.
- Tighten up the 2 screws.
- Adapt the front frame-panel into its place, by pushing it towards the wall.
Wiring Connections
| Switch | Y | 0 | Empty | Empty | R | C | HI | Empty | Empty |
|---|---|---|---|---|---|---|---|---|---|
| Function | Not in use | 24Vac | Fan | Not in use | Proportional output for cool and | ||||
| heat | 24Vac | HI FAN |
Switching the Thermostat On
- Press the ON button to activate the thermostat.
- ON will appear on display.
Switching the Thermostat Off
- Press the OFF button to deactivate the thermostat.
- OFF will appear on display.
Setting the Temperature
- Press the (+) or (-) the temperature will flash.
- Change the set temperature using the (+) or (-) buttons.
Selecting Modes
- Press the MODE button to switch between:
- Cool
- Heat
- Fan only
Meitav-tec Ltd (Contel group)
Tel: 972-3-9626462 Fax: 972-3-9626620
www.meitavtec.com –
support@meitavtec.com
FMH24-PD-1S-IR
Owner’s Manual – Installation and Operating Instructions
Please read this manual carefully before installation and use.
Overview
Is very important to find the right place to install the Flush Mount unit.
Please make sure to follow all the installation instructions in order to get
an
accurate reading of the temperature.
General points to follow:
- The unit MUST be fitted into a standard electrical box (GEWISS Box – GW00001481VR)
- The unit should not be installed on an outside wall or where there is an air draft.
- The unit must not be exposed to a direct sunlight.
- The standard height to install this unit is 1.5 meter from the floor (5 feet).
Installation procedure:
-
Connect the wires (see #2)
-
Put the thermostat in the electrical box.
-
Tighten up the 2 screws.
-
Adapt the front frame-panel into its place, by pushing it towards the wall.
Product Wiring Connections
| Switch | Function |
|---|---|
| Y |
0
Empty| Not in use
Empty
R| 24Vac
C
HI| Fan
Empty| Not in use
Empty
Operating Manual
Switching the thermostat On
- Press the ON button to activate the thermostat.
- ON will appear on display.
Switching the thermostat Off
- Press the OFF button to deactivate the thermostat.
- OFF will appear on display.
Setting the temperature
- Press the (+) or (-) the temperature will flash.
- Change the set temperature using the (+) or (-) buttons.
Selecting modes
- Press the MODE button to switch between:
- Cool
- Heat
- Fan only
F ile: fmh24-pd-1s-A4-rev1.doc Rev. 1
Date: 07/06/2005
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>