Weller T0058762701 Zero Smog EL Kit Instruction Manual

: June 15, 2024
: Weller

Table of Contents

Weller T0058762701 Zero Smog EL Kit
Included in delivery
Accessory
Starting up the device
Operation
Safety information
Warranty
Care and maintenance
Technical Data
Symbols
Product Registration
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Weller T0058762701 Zero Smog EL Kit

Weller-T0058762701-Zero-Smog-EL-Kit-PRODUCT

Included in delivery

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-1

Accessory

Starting up the device

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-3

Operation

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-6

Operating time filter display

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-7

Extraction capacity filter display

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-8

Filter change

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-9

Check the prefilter and the main filter

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-10

For your safety

Read these instructions and the accompanying safety information carefully before starting up the device and starting work with the device.
Keep these instructions in a place that is accessible to all users.

Thank you for the confidence you have shown in buying this device.
The device has been manufactured under the most rigorous quality standards which ensure that it operates perfectly.
These instructions contain important information that will help you to start up, operate, and service the device safely and correctly as well as to eliminate simple faults and malfunctions yourselves.
Always pass on the device to third parties together with these operating instructions.
The device has been manufactured under state-of-the-art technology and acknowledged regulations concerning safety.
There is nevertheless the risk of personal injury and damage to property if you fail to observe the safety information set out in the accompanying booklet and the warnings given in these instructions.

Safety information

This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be done by children without supervision.

Warning! Electrical shock
If the device is faulty, active electrical conductors may be bare or the PE conductor may not be functional.

Repairs must always be referred to a Weller-trained specialist.
If the electrical tool‘s power supply cord is damaged, this must be replaced with a specially prefabricated power supply cord available through the customer service organisation.

Warning! Danger of injury
The device or parts of the device may fall off during transportation.

Hold the device by the intended handles only.
Never use the device as a means of transportation.

Warning! Danger of asphyxiation, Danger of poisoning
Improper installation can result in above-normal workplace concentrations

Measure the workplace concentration upon completion of installation work
Inappropriate maintenance cycles for gas media may result in above-normal workplace concentrations
Specify maintenance cycle
Above-normal contamination levels in the ambient air during cleaning work on the pipe system/ extraction area
If suction capacity is impaired by build-up within the pipe system, replace the contaminated parts A saturated activated carbon filter will not be able to capture harmful substances. The harmful substances will be released back into the environment unfiltered.
Observe the recommended filter replacement intervals.
High concentrations of harmful gases can lead to overheating of the activated carbon and possibly trigger spontaneous combustion of the filter.
Run the unit on clean air for several minutes before switching off.

Specified Conditions Of Use
This filtration system is suitable for the extraction and filtration of particles and gases, depending on the filter medium used.

Warning! Danger of asphyxiation, Danger of poisoning
Improper use may result in respiratory problems, asphyxiation, poisoning or cancer

Particles and gases which are unsuitable for the filter medium in use may not be extracted.
Liquids and flammable gases may not be extracted
Never use the device without a filter or with a full filter.
Never use the device without the fan cover

This device may only be used at room temperature and indoors.

The unit is designed for use as a surface extraction unit and is not suitable for extracting fumes directly
from the soldering gun.
The intended use of the soldering station/ desoldering station also includes the requirement that you
- adhere to these instructions,
- observe all other accompanying documents,
- comply with national accident prevention guidelines applicable at the place of use.
Soldering or welding enamelled wire
For soldering and welding enamelled wire, use the standard prefilter – medium filter M5.
Extraction of adhesive vapours
Use a broadband gas filter (without a suspended matter filter) for the extraction of adhesive vapours.
The manufacturer will not be liable for unauthorised modifications to the device.

User groups
Due to differing degrees of risk and potential hazards, several work steps may only be performed by trained experts.

Work step

Installation of complex pipe systems with multiple extractor arms connected
Replacing electrical replacement parts
Specification of maintenance intervals
Operation Filter change
Installation of complex pipe systems with multiple extractor arms connected Replacing electrical replacement parts

User groups

Specialist personnel with technical training
Electricians
Safety expert
Non-specialists
Technical trainees under the guidance and supervision of a trained expert

Warranty

Claims by the buyer for physical defects are time-barred after one year from delivery to the buyer. This does not apply to claims by the buyer for indemnification under §§ 478, 479BGB (German Federal Law Gazette).
We shall only be liable for claims arising from a warranty furnished by us if the quality or durability warranty has been furnished by use in writing and using the term „Warranty“.
The warranty shall be void if damage is due to improper use and if the device has been tampered with by unauthorised persons.
Subject to technical alterations and amendments.
For more information please visit www.weller-tools.com

Care and maintenance

Warning!
Before doing any work on the machine, pull the plug out of the socket. Use original replacement parts only.
Contaminated filters must be treated as special waste. Dispose of replaced equipment parts, filters or old devices under the rules and regulations applicable in your country.
Notice
Different fluxes and flux constituents and the amount of and size of dust particles in the extracted air will significantly affect the filter’s working life. Submicron particles in the extracted air increase when soldering or welding to varnish insulated wire.

To ensure that the filtration system functions properly, the compact filter must be replaced as follows

at least once a year or
if the maximum allowable workplace concentration is exceeded or
as per the maintenance schedule

The suspended matter filter and the broadband gas filter are complementary to one another and can be replaced together as a compact filter. The compact filter must be changed once a year to ensure it is fully functional. The fine dust filter (filter mat) is the preliminary stage of the compact filter and therefore must be replaced more frequently.
It is strongly recommended that the compact filter be replaced after no more than 10 fine dust filter changes.

The red warning light is flashing:
The recommended service life of the filter has expired. Indicates that the filter needs changing. Reset the warning with the reset function on the control panel and schedule a filter change.
The red warning light is lit continuously:
The extraction capacity is too low. Switch off the filter unit. Check the nozzles and tubes, and clean them if necessary. If the red warning light comes on again the next time the unit is turned on, the filter must be changed.
If no action is taken, the filter unit will cut out after five minutes to avoid overheating.
When changing the main filter the filtration time can be reset as follows:.
Hold the fan button down and, at the same time, turn on the switch until the red warning light flashes for 3 sec.

Error messages and error clearance

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-20

Technical Data

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-21

Symbols

Caution!
Read the operating instructions!
Before performing work of any kind on the unit, always disconnect the power plug from the socket.
ESD-compatible design and ESD-compatible workstation
CE mark of conformity
British Conformity Mark

Disposal
Do not dispose of electric tools together with household waste material! In observance of the European Directive on waste electrical and electronic equipment and its implementation under national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Contaminated filters must be treated as special waste. Dispose of replaced equipment parts, filters or old devices under the rules and regulations applicable in your country.

Zero Smog EL

Weller-T0058762701-Zero-Smog-EL-Kit-FIG-18