ORACURA OC010 Smart Water Flosser Instruction Manual
- June 3, 2024
- ORACURA
Table of Contents
Smart
Water Flosser
Operating Instructions
OC010
Before operating this product, please read these instructions completely and save this manual for future use.
IMPORTANT SAFEGUARDS
All information provided in this section is directed to guide you toward the
correct and safe operation of this device. By following the instructions, you
can avoid injuries to yourself and others, as well as avoid damage to
property.
READ ALL INSTRUCTIONS BEFORE USING
DANGERS
- Toddlers, infants, and people who are unable to operate should not be allowed to use this appliance. Please keep it out of reach of children.
- Never alter the appliance. Also, do not try to disassemble or repair it.
- Do not place or store the product where it can fall or be pulled into a tub or sink.
- Do not reach for the product that has fallen into the water. Unplug immediately.
- Do not use the product while bathing.
WARNINGS
-
This appliance can be used by children aged 8 years and above.
People with reduced physical, sensory or mental capabilities, lack of experience, and knowledge can also use the appliance if given proper supervision or instruction concerning the use of the appliance in a safe way by understanding the hazards involved. -
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
The appliance is only to be used with the power supply unit provided with the appliance.
-
The battery must be removed from the appliance before it is scrapped.
-
The appliance must be disconnected from the supply mains while removing the battery
-
The battery is to be disposed of safely.
-
Regarding how to remove the battery, please refer to the “disposal” section on page 7.
-
Do not fill the tank with water warmer than 40 ºC.
-
If the external flexible cable or cord of this transformer is damaged, replace it with the manufacturer or the service agent, or a similarly qualified person to avoid the hazard.
-
Keep the cord away from heated surfaces.
-
Please do not use it if the nozzle is lost.
-
Do not submerge the device in water.
-
Do not use the device for any other purpose other than oral cleaning.
-
Keep the nozzle away from small children. The nozzle is small enough to be swallowed and it can get lodged in the throat.
-
Certain types of mouthwash may damage the equipment by causing the housing or water reservoir to crack. Therefore, do not use mouthwash in the water reservoir.
-
People who experience tooth or gum pain may not be able to use this device and should consult their dentist.
-
Do not press the nozzle too firmly against your teeth or gums.
Doing so may injure your gums.
FOLLOW THESE INSTRUCTIONS
Configuration
a. Nozzle release button
b. On/Off button
c. Mode button
d. Mode indicator
e. Charging base
f. Charging base cover
g. Nozzle
h. The identification ring
i. Nozzle suction tube
j. Filter
k. Water tank
l. Water tank cap
Note:
There may be some liquid remaining inside the main appliance before use (tank,
water suction tube, etc). This is the remaining distilled water that was used
for the performance (water flow) test, so there are no health concerns
regarding the same.
How to use
Charging the device (Fig. 1)
- Take the charger base cover down and insert the appliance plug securely into the appliance socket. Before inserting the appliance plug, make sure that there is no remaining liquid inside the socket.
- Insert the charging adaptor securely into the power outlet.
- The “CH” indicator blinks when the device is charging and it will turn off after it is fully charged.
- Recover the cover onto the charger base again after charging is finished.
Note:
If the “CH” indicator is blinking during or after water flossing, it means
that the battery needs to be recharged. Full recharging will take about 4
hours.
Use
the Smart Water Flosser
-
Attach the nozzle to the unit. (Fig. 2)
-
Open the water tank cap to fill the tank with water at which the temperature does not exceed 40ºC. Close the cap. (Fig. 3)
-
OR Slide the water tank down off the unit, fill the tank with water at which the temperature does not exceed 40ºC, then attach the tank to the unit. (Fig. 4)
-
Press the “Mode” key to select the mode that you desire. You can also change the working mode during the process of your water flossing. (Fig. 5).
Normal: for normal cleaning.
Soft: for gentle cleaning of sensitive gums.
Pulse: for cleaning and massaging the gums. -
Hold the unit in an upright position with the nozzle tip pointing toward your teeth.
-
Keep your mouth slightly open so that the water can flow out.
-
Press the “On/Off” key to start the water flossing process.(Fig. 6)
• Directing the water jet flow at a 90-degree angle to the teeth and gums.
• Directing the water jet slowly along with the teeth.
• Directing the water jet along the gum line with the nozzle tip at a 90-degree angle to the gum tissue.
• Cleaning between the teeth and around any braces, crowns, or bridgework thoroughly. -
Press the “On/Off” key and then press the nozzle release button to replace other nozzles as per your need. (Fig.7)
-
Once water flossing is completed, press the “On/Off” key again to turn off the device.
-
Switch off your device and place it in the protected case after use.
After using the appliance (Fig.8)
- Open the water tank cap and dispose of the water in the tank.
- Press the “On/Off” key to turn on the unit, and drain the water inside the appliance.
- Press the “On/Off” key again to turn off the unit, and close the water tank cap.
- Wipe the device with a dry cloth.
Note:
To prevent bacteria from propagating, make sure there is no remaining water
inside the unit. If you’re not going to use the appliance for a long time,
make sure to wipe and dry the appliance before storing it.
Maintenance
Use only water or a neutral cleaning agent to clean the device. Never use
Main unit
caustic or abrasive agents (e.g., vinegar or lime scale removers), since they
may damage the device. Do not wash using hot water of over 50ºC.
Keep the device away from high-temperature areas and avoid direct sunlight.
- Remove the dirt by wiping the unit. Use a cloth with liquid soap to clean it and wipe it off using a dry cloth.
- Do not submerge the main unit in water to clean it.
- Dry after washing with water.
Water tank cap
Wipe off any grime and dirt with a cloth.
Nozzle
- Wash with water and wipe with a soft cloth.
- Replace the nozzle every 6 months.
Water suction tube
- Wash with water and wipe with a soft cloth.
- Do not bend, pull or twist the water suction tube.
Tank
- Wash with water and wipe with a soft cloth.
- Dry the tank when not used for a long period.
Tank Troubleshooting
Problem | Possible Cause | Solution |
---|---|---|
It does not work | You’ve just purchased the product or it has been left unused | |
for more than 3 months. | Charge the unit for at least 4 hours. | |
It only works for a few minutes even after charging | The battery has reached | |
the end of its life cycle. | Contact the service center for support. | |
Charging time was insufficient. | Charge the unit for at least 4 hours. | |
Water pressure is very low | There is dirt stuck in the nozzle | Replace the |
nozzle
The nozzle is deformed
There is dirt stuck in the filter| Clean the filter
Water does not come out| The tank is empty| Fill up tank
The appliance is tilted too much while in use| Use with the appliance in a
vertical state
You’ve just purchased the product or it has been left unused for a period.|
Pull out the nozzle then flush the nozzle hole on the body.
Disposal
The rechargeable battery inside your appliance is easy to remove for
recycling.
At the end of the product’s life and prior to disposal, please remove the
rechargeable battery from the handle by following the instructions below.
During the below operation, be sure to protect your eyes, hands, fingers, and
the surface on which you work.
-
Remove 2pcs rubber feet on the bottom of the handle. (Like in Fig. 9)
-
Insert a screwdriver into the slot located at the bottom of the handle and turn counterclockwise to release the bottom cap (Like in Fig. 9)
-
Slide the water tank down off the device and unscrew the two screws beside the suction tube. (Fig. 10)
-
Open the top cover and put the inner out of the unit, then unscrew all the screws of the inner.(Fig.11)
-
Cut off the battery line and pull out the batteries from the inner.(Fig. 12)
If you have recycling questions, please contact your local waste management office.
ORACURA Solutions Pvt Ltd,
6th Floor, Unit 1, Vidhani Kalpavruksha,
H233-2, MIDC, T.T.C. Industrial Area, Nerul.
Navi Mumbai 410706
Toll-Free: 1800-120-7201
WhatsApp: +91 77387 33700
Email: support@oracura.in
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>