Blaupunkt TYRE INFLATOR TIF 22 DA – 12V User Guide
- June 5, 2024
- Blaupunkt
Table of Contents
TYRE INFLATOR
TIF 22 DA – 12V
Suitable for Car, Motorcycle, Bicycle, and other Sports equipment
Product Description
1. Digital Guage
2. Carry Handle
3. LED Lamp
4. Quick Release Nozzle Inflator Rubber Hose| 5. LED lamp turns ON
6. Inflator ON / OFF Switch
7. Power Cord
8. Cigarette Lighter Adaptor
---|---
Specification:
- Inflator with Digital Gauge & AutoStop
- Input: DC 12V Y Rated Power: 100W
- Rated Current: 8A
- Max Pressure: 120 PSI / 8.2 BAR
- Cylinder diameter: 22mm
- Max. Duty Cycle: 8 min
- Recommended for Sedans & Hatchback vehicles
- Function: Tyre inflator with PRESET & AUTO STOP
- Additional Function: LED work light
- Power Cord length: 3 meters with cigarette lighter plug.
- Air hose: 50cm rubber hose with quick release valve connector
- Accessories: 2 nozzle adaptors & 1 sports equipment needle nozzle
Instructions:
- Start the vehicle and insert the cigarette lighter adaptor into the 12V cigarette lighter outlet provided in the vehicle.
- The device comes with a 3M long Power Cord which makes it convenient to connect the front & back tires. Fig. 1
- Attach the Quick Release Nozzle to the valve stem of the tire.
- Place the device on a preferably flat surface and set the preferred tire pressure on the digital dial (Fig 2).
- Turn on inflator device. Make sure there are no leaks at the point where the quick release nozzle meets the valve stem of the tire.
- Once the desired tyre pressure is reached, the unit turns off automatically.
- This tire pressure inflator comes equipped with a LED light that makes it convenient to use at night.
- This device is designed to work non-stop for around 7- 8 minutes (the typical time required to inflate 13″-16″ tires). It is suggested to not use the device beyond these 7-8 minutes at a stretch. A 2-3 minute interval may be required to improve the efficiency of this device in the long run.
Product Parameters:
| Input Voltage | DC 12V | Power | 110W |
|---|---|---|---|
| Power Cord Length | 3 Meters | Cylinder Diameter | 30MM |
| MAX Duty Cycle | < 10 min | MAX Air Pressure | 150PSI |
Helpful Tips:
- Do NOT keep the device near a heat source
- Do NOT use this device near flammable liquids or gas sources
- Should the device need attention, please visit an Authorized Service Centre. Any attempt to service the device by an unauthorized person will VOID the warranty
- This device is designed to be used with a 12V supply source only. Do NOT attempt to use it with a 24V supply source
- This device is designed to be used to inflate tires of Sedans and small diameter tires only.
- It is normal for the device to get hot after continuous use.
- It is recommended to use this device to inflate tires for no longer than its suggested cycle time at a go.
Accessories: Following accessories are included in the package: 1 qty spare fuse and 3 qty multi-function air inflator nozzles.
Accessories: Following accessories are included in the package: 1 qty spare fuse and 3 qty multi-function air inflator nozzles.
Steps for changing fuse:
Unscrew the top of the cigarette lighter adaptor| Remove blown fuse & insert spare fuse provided| Screw the top end of the cigarette lighter adaptor to make a tight seal
Troubleshooting Guide
This section covers common problems the user may encounter while using this device.
| Nature of problem | Cause and recommended solution |
|---|---|
| Device not working | Fuse is blown – replace the fuse and check the device |
| The device is operating erratically | The quick-release valve connector is not |
connected to the valve stem securely – causing a leak and hence showing
erratic readings. Release the connector from the valve stem and reconnect
securely
The preferred tire pressure was not preset correctly and causes the display to
blink continuously. Turn off the device, set the preferred tyre pressure, and
Turn ON the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>