BLAUPUNKT 5GB31150AU Gas Hobs Instruction Manual

BLAUPUNKT 5GB31150AU Gas Hobs

Specifications:

• Model Numbers: 5GB31150AU, 5GB61151AU, 5GB62191AU, 5GB72290AU, 5GB91250AU, 5GB92290AU
• Type: Gas Hobs
• Power Supply: 220V-240V

Product Usage Instructions

Safety Instructions:
Please take the time to read this Instruction Manual before installing or using the appliance. It is important to follow the safety instructions to prevent any accidents or injuries. Ensure the manual is passed on if the appliance is sold or transferred to another person.

Installation:

Warning:
The appliance should be installed by regulations and used in a well-ventilated space. Before installation, verify that the gas and electrical supply match the specifications on the rating plate. Ensure that gas pipes and electrical cables do not come into contact with any parts of the appliance.

Child and People Safety:

Warning:
Do not allow children to play near or with the appliance as it gets hot during use. Keep children away from the appliance until it has cooled down to prevent burns or injuries.

During Use:

Warning:
Only use the appliance for cooking food. The burner panel is not intended to be operated by an external timer or remote control system.

FAQ:

What should I do if I suspect a gas leak?
If you suspect a gas leak, follow these steps:

1. Do not turn on any lights.
2. Avoid switching on/off electrical appliances or touching electric plugs.
3. Avoid using a telephone.
4. Stop using the product and close the gas valve.
5. Open windows for ventilation.
6. Contact the service center using a phone outside.

Preface

Thank you for choosing our gas cooktop.

• To use this appliance correctly and prevent any potential risk, read these instructions before using the appliance.
• Keep these instructions in a place where you can find them easily.
• If you are unsure of any of the information contained in these instructions, please contact our customer care center.
• The manufacturer shall not be responsible for any damages to persons or property caused by incorrect installation or use of the appliance.
• The appliance has been certified for use in countries other than those marked on the appliance.
• The manufacturer also reserves the right to make any modifications to the products as may be considered necessary or useful, also in the interests of the user, without jeopardizing the main functional and safety features of the products themselves.
• The appliance is designed for a domestic environment and not a commercial one.

Safety Instructions

• Please take the time to read this Instruction Manual before installing or using the appliance.
• This instruction booklet must be kept with the appliance for any future reference.
• If the appliance is sold or transferred to another person, ensure the booklet is passed on to the new user.
• The manufacturer declines any liability should these safety measures not be observed.
• The following marks are made to be easily understood so that you can prevent any accident caused by misuse in advance, and use the appliance more conveniently.
• Read the following contents thoroughly and ensure you understand them.

Danger/Warning| Neglect of this mark may result in severe personal injury or death.
---|---
Caution| Neglect of this mark may result in minor personal injury or property damage.

The following marks are used in the Instruction Manual as follows:

• Caution
• No Fire Tool
• No Access
• Must Do

Danger
If gas seems to leak, take the actions as follows:

• Do not turn on the light.
• Do not switch on/off any electrical appliance and do not touch any electric plug.
• Do not use a telephone.
  1. Stop using the product and close the middle valve.
  2. Open the window to ventilate.
  3. Contact our service center by using a phone outside.

The fuel gas contains mercaptan so that you can smell the gas leak (smell of rotten garlic or egg) even where only 1/1000 of the gas is in the air.

Installation

Warning

• This appliance shall be installed by regulations in force and only used in a well-ventilated space.
• Before installation, ensure that the gas and electrical supply complies with the type stated on the rating plate.
• Where this appliance is installed in marine craft or caravans, it should not be used as a space heater.
• The gas pipe and electrical cable must be installed in such a way that they do not touch any parts of the appliance.

Caution

• This appliance should be installed by a qualified technician or installer.
• The adjustment conditions for this appliance are stated on the label or data plate.
• Remove all packaging before using the appliance.
• After unpacking the appliance, make sure the product is not damaged and that the connection cord is in perfect condition. Otherwise, contact the dealer before installing the appliance.
• The adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature of 85°C above the ambient temperature of the room it is located in, whilst in use.
• In the event of burner flames being accidentally extinguished, turn off the burner control and do not attempt to re-ignite the burner for at least one minute.
• The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure that the kitchen is well-ventilated: keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).
• Prolonged intensive use of the appliance may call for additional ventilation, for example, opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.

Child and People Safety

Warning

• Do not allow children to play near or with the appliance. The appliance gets hot when it is in use.
• Children should be kept away until it has cooled.

Caution

• This appliance is designed to be operated by adults.
• Children can also injure themselves by pulling pans or pots off the appliance.
• This appliance is not intended for use by children or other persons whose physical, sensory, or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely.

During Use

Warning

• Only use the appliance for preparing food.
• Do not modify this appliance. The burner panel is not designed to operate from an external timer or separate remote control system.
• The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure that the kitchen is well-ventilated: keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).
• Do not use this appliance if it comes in contact with water. Do not operate this appliance with wet hands.
• The heating and cooking surfaces of the appliance become hot when they are in use, take all due precautions.
• Do not use large cloths, tea towels, or similar as the ends could touch the flames and catch fire.
• Never leave the appliance unattended when cooking.
• Unstable or misshapen pans should not be used on the appliance as they can cause an accident by tipping or spillage.

During Use

• Do not use or store flammable materials in the storage drawer near this appliance.
• Perishable food, plastic items, and aerosols may be affected by heat and should not stored above or below the appliance.
• Do not spray aerosols in the vicinity of this appliance while it is in operation.
• Ensure the control knobs are in the ‘ ‘position when not in use.

Caution

• This appliance is intended for domestic cooking only. It is not designed for commercial or industrial purposes.
• Prolonged intensive use of the appliance may call for additional ventilation, for example, opening of a window, or increasing the level of mechanical ventilation where present.
• Use heat-resistant pot holders or gloves when handling hot pots and pans.
• Do not let pot holders come near open flames when lifting cookware.
• Take care not to let pot holders or gloves get damp, as this causes heat to transfer through the material quicker with the risk of burning yourself.
• Only ever use the burners after placing pots and pans on them. Do not heat any empty pots or pans.
• Never use plastic or aluminum foil dishes on the appliance.
• When using other electrical appliances, ensure the cable does not come into contact with the appliance surfaces of the cooking appliance.
• If you have any mechanical parts eg. an artificial heart in your body, consult a doctor before using the appliance.
• Do not use a tea towel or similar materials in place of a pot holder. Such clothes can catch fire on a hot burner.
• When using glass cookware, make sure it is designed for top-plate cooking. If the surface is made of glass-cracked, switch off the appliance to avoid defeat electrocution.
• To minimize the possibility of burns, ignition of flammable materials, and spillage, turn cookware handles toward the side or center of the top plate without extending over adjacent burners.
• When using glass cookware, make sure it is designed for top-plate cooking. If the surface is made of glass-cracked, switch off the appliance to avoid defeat electrocution.
• To minimize the possibility of burns, ignition of flammable materials, and spillage, turn cookware handles toward the side or center of the top plate without extending over adjacent burners.
• Always turn burner controls off before removing cookware.
• Carefully watch foods being fried at a high flame setting.
• Always heat fat slowly and watch as it heats.
• Frying foods should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan.
• Never try to move a pan of hot fat, especially a deep-fat fryer. Wait until the fat is completely cool.

Cleaning and Service

Warning

• Never use abrasive or caustic cleaning agents.
• This appliance should only be repaired or serviced by an authorized Service Engineer and only genuine approved spare parts should be used.

Caution

• Before attempting to clean the appliance, it should be disconnected from the mains and cooled.
• You should not use a steam jet or any other high-pressure cleaning equipment to clean the appliance.

Environmental Information

• After installation, please dispose of the packaging with due regard to safety and the environment.
• When disposing of an old appliance, make it unusable, by cutting off the cable.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

• This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources.
• Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
• Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Description of the appliance

Model

| Top Plate| Dimension (WDH)| Ignition device| Gas Connection| Electric supply| Burner Feature| Σ Qn
---|---|---|---|---|---|---|---
5GB31150AU|

Glass

|

52030090

|  |  |  | Rapid(1), Auxiliary(1)| 15.1MJ/h
5GB61151AU| Stainless Steel|

59051090

|

Continuous

|  |

220-240Vac,

|

Triple-Crown(1) Semi-rapid(2), Auxiliary(1)

Triple-Crown(1) Rapid(1),

Semi-rapid(2), Auxiliary(1)

|

30.4MJ/h

5GB62191AU| Glass|
60051590| Ignition

Type

| G1/2 thread| 50Hz-60Hz,

2W

|
5GB72290AU| Glass|

75051090|  |  |  |
5GB91250AU| Stainless Steel|

86051090

|  |  |  | 41.2MJ/h
5GB92290AU|

Glass

|

90051099

|  |  |  |

Accessories

How to Use the Appliance

The following symbols will appear on the control panel, next to each control handle:

• Black circle: gas off

• Large flame: maximum setting

• Small flame: minimum setting

• The minimum setting is at the end of the anti-clockwise rotation of the control handle.

• All operation positions must be selected between the maximum and minimum positions.

• The symbol on the control panel, next to the control handle will indicate which burner it operates.

Automatic ignition with flame failure safety device
The appliance is fitted with a flame failure safety device on each burner, which is designed to stop the flow of gas to the burner head in the event of the flame going out.

To ignite a burner:

• Press the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position.
• If you keep the control knob depressed, the automatic ignition for the burner will operate.
• You should hold down the control knob for 15 seconds after the flame on the burner has lit. If after 15 seconds the burner has not lit, stop operating the device and open the compartment door and/or wait at least 1 minute before attempting a further ignition of the burner.
• After this 15-second interval, to regulate the flame you should continue turning the control knob anti-clockwise until the flame is at a suitable level. The operating position MUST be at a position between the maximum and minimum position.
• To switch the burner off, turn the control knob fully clockwise to the gas-off position.
• In case of power failure, the burners can be lit by carefully using a match.

Safety and Energy-saving advice

The diameter of the bottom of the pan should correspond to that of the burner.

BURNERS|
---|---
min.| max.
Triple-Crown| 200mm| 240mm
Rapid| 200mm| 240mm
Semi-Rapid| 160mm| 180mm
Auxiliary| 120mm| 160mm

Do not use cookware that overlaps the edge of the burner.

• It is not recommended to use roasting pans, frying pans, or grill stones heated simultaneously on several burners because the resulting heat build-up may damage the appliance.
• Do not touch the top plate and trivet whilst in use for a certain period after use.
• As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering.

Cleaning and Maintenance

• Cleaning operations must only be carried out when the appliance is completely cool.
• The appliance should be disconnected from your mains supply before commencing any cleaning process.
• Clean the appliance regularly, preferably after each use.
• Abrasive cleaners or sharp objects will damage the appliance surface; you should clean it using water and a little washing-up liquid.

Pan support, Control handles

• Take off the Pan support.
• Clean these and the control handles with a damp cloth, washing up liquid and warm water. For stubborn soiling, soak beforehand.
• Dry everything with a clean soft cloth.

Top plate

• Regularly wipe over the top plate using a soft cloth well wrung out in warm water to which a little washing-up liquid has been added.
• Dry the top plate thoroughly after cleaning.
• Thoroughly remove salty foods or liquids from the hob as soon as possible to avoid the risk of corrosion.
• Stainless steel parts of the appliance may become discolored over time. This is normal because of the high temperatures. Each time the appliance is used these parts should be cleaned with a product that is suitable for stainless steel.

BURNERS

• Remove the burner lids and Flame Spreaders by pulling them upwards and away from the top plate.
• Soak them in hot water and a little detergent or washing-up liquid.
• After cleaning and washing them, wipe and dry them carefully. Make sure that the flame holes are clean and completely dry.
• Wipe the fixed parts of the burner cup with a damp cloth and dry afterward.
• Gently wipe the ignition device and flame supervision device with a well-wrung-out cloth and wipe dry with a clean cloth.
• Before placing the burners back on the top plate, make sure that the injector is not blocked.

Re-assemble the Auxiliary, Semi-Rapid, Rapid, and Triple-Crown burners as follows:

1. Place the flame spreader ( 4 ) onto the burner cup ( 5 ) so that the ignition device and the flame supervision device extend through their respective holes in the flame spreader. The flame spreader must click into place correctly.
2. Position the burner lid ( 1,2,3 ) onto the flame spreader ( 4 ) so that the retaining pins fit into their respective recesses.

Replace parts in the correct order after cleaning.

• Do not mix up the top and bottom.
• The locating pins must fit exactly into the notches.

Using instructions

Warnings

• Do not modify this appliance.

• This appliance must be installed by an authorized technician or installer.

• Before installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible.

• The adjustment conditions for this appliance are stated on the label (or data plate).

• This appliance is not connected to a combustion products evacuation device. It should be installed and connected according to current installation regulations. Particular attention should be given to the relevant requirements regarding ventilation.

• Before installing, turn off the gas and electricity supply to the appliance.

• All appliances containing any electrical components must be earthed.

• Ensure that the gas pipe and electrical cable are installed in such a way that they do not touch any parts of the appliance that may become hot.

• Gas pipes or connectors shouldn’t be bent or blocked by any other appliances.

• Check the dimensions of the appliance as well as the dimensions of the gap to be cut in the kitchen unit.

• The panels located above the work surface, directly next to the appliance, must be made of non-flammable material. Both the strati- fied surfacing and the glue used to secure it should be heat resistant, to prevent deterioration.

• Turn on the appliance tap and light each burner.

• Check for a clear blue flame without yellow tipping.
  If burners show any abnormalities check the following :

  • The burner lid is on correctly
  • The flame spreader is positioned correctly
  • Burner vertically aligned with injector nipple

• A full operational test and a test for possible leakages must be carried out by the fitter after installation.

• The flexible hose shall be fitted in such a way that it cannot come into contact with a moveable part of the housing unit and does not pass through any space susceptible to becoming congested.

• Grease cranes are produced at the factory to meet the requirements of all life hobs.

Positioning

This appliance is to be built into a kitchen unit or 600mm worktop, providing the following minimum distances are allowed;

• The edges of the hob must be a minimum distance of 60 mm from a side or rear wall.
• 700 mm between the highest point of the hob surface (including the burners) and the underside of any horizontal surface directly above it.
• 400 mm between the hob surfaces, providing that the underside of the horizontal surface is in line with the outer edge of the hob. If the underside of the horizontal surface is lower than 400 mm, then it must be at least 50 mm away from the outer edges of the hob.
• 50 mm clearance around the appliance and between the hob surface and any combustible materials.
• You must have a gap of at least 25 mm and at most 74 mm between the underneath of the appliance and any surface that is below it.
  • An oven must have forced ventilation to install a hob above it.
  • Check the dimensions of the oven in the installation manual.
  • The cutout size must obey the indication.

Installing the appliance

1. Remove the pan supports, the burner lid, and the flame spreader carefully turn the appliance upside down, and place it on a cushioned mat.
   Take care that the Ignition devices and flame supervision devices are not damaged in this operation.

2. Apply the sponge provided around the edge of the appliance.

3. Do not leave a gap in the sealing agent or overlap the thickness.

4. IMPORTANT: In addition to the sponge around the edge of the appliance; ensure an additional strip is applied on each side as per the diagram.

Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the appliance from the aperture in future, particularly if it needs to be serviced.

1. Place the bracket (B) over the holes that match the size of the screws. There is one set of screw holes in each corner of the hob (H) – Slightly tighten a screw (C) through the bracket (B) so that the bracket is attached to the hob, but so that you can still adjust the position.
2. Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out.
3. On the underneath of the hob, adjust the brackets into a position that is suitable for your worktop. Then fully tighten the screws (C) to secure the hob into position.

Gas Connection

• This appliance must be installed and connected by installation regulations in force in the country in which the appliance is to be used.
• This appliance is supplied to run on natural gas only and cannot be used on any other type of gas without modification. Conversion for use on LPG and other gases must only be undertaken by a qualified person.
• Turn off power for safety and appliance protection. Close the middle valve to prevent gas leakage.
• Keep away from inflammable materials around appliances.
• Before work, put on gloves.

CAUTION
Cool off the appliance for a while right after using the appliance for your safety because you can get burners from high temperatures from the appliances.

Most of the tools that you might need are shown below. Some are optional.

Replacement of gas-type fitting

Tool: Open-end wrench

Steps for operation:

• Disassemble with a wrench the gas-type fittings from the main gas tube.
• When you disassemble/assemble the gas connection, use 2 spanners. One for fixing the gas connection elbow, and the other for tightening the gas hose.
• Look tightly for a replaceable gas-type fitting onto the main gas tube.

LPG CONVERSION – REGULATOR

This appliance is supplied and set up for Natural Gas usage. A conversion kit is included with the product for Universal LPG usage. The conversion kit contains the appropriate injectors and 1 LPG sticker.

Please follow the procedure below if a conversion to suit UNIVERSAL LPG is required:

This appliance is supplied and set up for natural Gas usage. A conversion kit is included with the product for universal LpG usage. the conversion kit contains the appropriate injectors and 1 LpG sticker.

please follow the procedure below if a conversion to suit unIVErSAL LpG is required:

1. Remove the hotplate trivets, burner caps, and burner crowns to access the hotplate injectors. replace the factory-fitted injectors with the appropriate injectors, as supplied. refer to the injector orifice table for injector sizes. the injector size is stamped on the side of the injector.

2. unscrew the top hat nut from the regulator. the top hat nut and control pressure spring assembly will disengage as an assembly.

3. unscrew the threaded pin from a top hat.

4. Upturn the threaded pin, so the spring is free, and screw the pin back into the top hat until firm.

5. refit the top hat nut assembly to the regulator ensuring that it is fully screwed down. the regulator is now set for connection to LpG.

6. turn on the gas supply and at each new connection check for leaks using soapy water. Each hotplate valve should be turned on, one at a time, and the injector hole blanked off for several seconds.

7. the operation of the regulator can be confirmed by connecting a manometer to the pressure test point located on the side of the regulator body adjacent to the outlet.
   With the appliance operating check the outlet pressure

   • when all burners of the appliance are operating at maximum,
   • when the smallest burner of the appliance is operating at minimum. under these conditions, the outlet pressure should not vary from the nominal outlet pressure of 2.60kpa by more than ±0.52kpa.

8. If the regulator appears to not be performing satisfactorily then check the following points:

   • If the outlet pressure is consistently too low then the inlet pressure may be too low and adjustment of an upstream regulator may be needed, or an upstream regulator or valve with insufficient flow capacity may be present in the gas supply line.
   • If this is suspected then it may be necessary to repeat the checks whilst measuring both the inlet and outlet pressure to determine if the inlet pressure is in the range 2.75 – 7.00kpa.
   • Check that the insert has been fitted correctly.
   • Check that the turret screw is fully screwed down.
   • Check that the regulator has been fitted to the gas supply line in the correct orientation, the arrow on the base of the body indicates the direction of gas flow.
     Once these checks have been completed, if the regulator still fails to perform satisfactorily it should be replaced.

9. One by one, turn the knobs to a minimum and screw in the bypass screw (accessible when the knob is removed) until a small stable flame results. turn the knob to the maximum and then back to the minimum to ensure that the correct minimum flame is maintained.

10. Attach the LPG sticker to the cooker, near the gas supply inlet. Cover the natural Gas label that is factory-fitted.

Statutory requirements
This installation must conform to the following:

• Manufacturer’s Installation instructions
• Local Gas Fitting Regulations
• Municipal Building Codes
• Refer to AS/NZS 5601.1 for Gas Installations
• S.A.A. Wiring Code
• Local Electrical Regulations
• Any other statutory regulations

Preparing to install
Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout. Only an officially authorized technician should connect the appliance. Before you begin, turn off the gas and electricity supply.

• A full operational test and a test for possible leakages must be carried out by the fitter after installation.
• Access to the whole length of the connection hose must be possible and the gas hose must be replaced before its use before the end of service life (indicated on the hose.)
• Before Leaving-Check all connections for gas leaks with soap and water.
• DO NOT use a naked flame for detecting leaks. Ignite all burners both individually and concurrently to ensure the correct operation of gas valves, burners, and ignition. Turn gas taps to a low flame position and observe the stability of the flame for each burner individually and all together. Adhere the duplicate data plate to an accessible location near the hotplate. When satisfied with the hotplate, please instruct the user on the correct method of operation. In case the appliance fails to operate correctly after all checks have been carried out, refer to the authorized service provider in your area.
• Flexible Hose: If installed with a hose assembly, it must comply with AS/NZS 1869,10mmID, class B or D, no more than 1.2 m long, and installed by AS/NZS 5601.1.
• Ensure that the hose does not contact the hot surfaces of the hotplate, oven, dishwasher, or any other appliance that may be installed underneath or next to the hotplate. The hose should not be subjected to abrasion, kinking, or permanent deformation and should be able to be inspected along its entire length with the cooktop in the installed position. Unions compatible with the hose fittings must be used and all connections tested for gas leaks. The supply connection point shall be accessible with the appliance installed.
• WARNING: Ensure that the hose assembly is restrained from accidental contact with the flue outlet of an underbench oven.

Gas Connection
Install by relevant gas standards and/or codes of practice applicable.

Connect the elbow fitting to the appliance gas manifold connection, and check that the seals between the elbow and manifold connection are in place and in good condition.

• For Natural gas: connect the natural gas appliance regulator (pictured opposite) with an integral test point using approved gas thread tape or compound to the elbow fitting.
• Ensure the supply connection point, test point and natural gas regulator adjustment screw (for Natural gas installation) are accessible for testing and/or adjustment with the hotplate in the installed position.
• Where a flexible hose assembly is used, ensure it is approved to AS/NZS 1869, Class B. Any hose assembly used must be restrained from accidental contact with the flue outlet of an under-bench oven.
• This hose assembly shall be suitable for connection to a fixed consumer piping outlet located as follows:
• Hotplates at a point 800 mm to 850 mm above the floor and in the region outside the width of the appliance to a distance of 250 mm.
• After connecting to the gas, check for leaks using the soapy solution, never a naked flame.

Gas Specification

Model No.| Gas type & pressure| Heat input and orifice size marked(mm)|
---|---|---|---
Wok burner| Rapid burner| Semi-rapid| Auxiliary|

5GB31150AU

|  | 13.5MJ/h| 10.8MJ/h| 6.3MJ/h| 4.3MJ/h|
Universal LP Gas 2.75kPa|

/

|

0.90

|

/

|

0.58

|
Natural Gas 1.0kPa|

/

|

1.50

|

/

|

0.93

|
 | Universal|  |  |  |  |
5GB61151AU| LP Gas 2.75kPa| 1.00| /| 0.68| 0.58|
5GB62191AU|
Natural Gas 1.0kPa|

1.72

|

/

|

1.15

|

0.93

|
 | Universal|  |  |  |  |
5GB72290AU

5GB91250AU

| LP Gas 2.75kPa| 1.00| 0.90| 0.68| 0.58|
 |  |  |  |  |
5GB92290AU| Natural Gas 1.0kPa|

1.72

| 1.50|

1.15

|

0.93

|

Electrical Connection

• This appliance must be earthed.
• This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
• The wires in the mains lead are colored by the following code;
  • Green/yellow = Earth
  • Blue = Neutral
  • Brown = Live

The wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol.

WIRING DIAGRAM

When the power cord is damaged it must be replaced by the manufacturer, a customer service agent, or similarly qualified personnel.

Gas adjustment

• Take precautions on the operations and adjustments to be carried out when converting from one gas to another.
• All work must be carried out by a qualified technician.
• Before you begin, turn off the gas and electricity supply to the appliance.

Change the injector of the burners.

• Remove the pan support, Burner lid, and Flame spreader.
• Unscrew the injector using a 7mm box spanner and replace it with the stipulated injector for a new gas supply. Carefully reassemble the all components.
• After injectors are replaced, it is advisable to strongly tighten the injector in place.

Adjustment of minimum level of the flame.

1. Turn the taps down to a minimum.

2. Remove the knob from the tap and place a small bladed screwdriver in the center of the adjustment screw.

3. The correct adjustment is obtained when the flame has a length of about 3 – 4 mm.

   • For butane/propane gas, the adjusting screw must
   • be tightly screwed in.
   • Refit the control knob.
     Make sure that the flame does not go out by quickly turning from maximum flow to minimum flow. If it does then remove the control knob and make further adjustments to the gas flow, testing it again once the adjustment has been made.

4. Repeat this process for each one of the gas taps.

5. Attach the ULPG sticker to the cooker, near the gas supply inlet. Cover the Natural label that is factory-fitted.

• Do not dismantle the tap Shafe: in the event of a malfunction, change the whole tap.
• Before placing the burners back on the top place, make sure that the injector is not blocked.
• A full operational test and a test for possible leakages must be carried out after gas conversion. (such as soap water or gas detector)
• After completing a conversion, a qualified technician or installer has to mark “V” on the right gas category to match the setting in the rating plate. Remove the previous setting “V” mark.

Troubleshooting

• Repairs should be performed by a licensed technician only. Improper repair may result in considerable danger to you and others.
• However, some minor problems can be resolved as follows:

Not ignited

| No Spark.| Check the electricity supply.
The burner lid is badly assembled.| Assemble the lid correctly.
The gas supply is closed.| Open the gas supply completely.
Badly ignited| The gas supply is not completely open.| Open the gas supply completely.
The burner lid is badly assembled.| Assemble the lid correctly.
The ignition plug is contaminated with an alien substance.| Wipe the alien substance with a dry cloth.
The burners are wet.| Dry the burner’s lids carefully.
The holes in the flame spreader are clogged.| Clean the flame spreader.
Noise made when combusted and ignited| The burner lid is badly assembled.| Assemble the burner lid correctly.
The flame goes out when in use.| The flame supervision device is contaminated with alien substances.| Clean the flame supervision device.
The product being cooked has boiled over and extinguished the flame.| Turn off the burner knob. Wait one minute and reignite the zone.

A strong draught may have blown the flame out.

| Please turn off the zone and check the cooking area for draught such as open windows. Wait one minute and reignite the zone
Yellow Flame| The holes in the flame spreader are clogged.| Clean the flame spreader.
Different gas is used.| Check the gas used.
Unstable Flame| The burner lid is badly assembled.| Assemble the burner lid correctly.
Gas Smell| Gas leakage| Stop using the product and close the middle valve. Open the window to ventilate.

Contact our service center by using a phone outside.

If the problem is not solved, please contact the customer care center.

www.blaupunkt-einbaugeraete.com

• Deutschland/Germany
  service.DE@blaupunkt-einbaugeraete.com

• Österreich/Austria
  service.AT@blaupunkt-einbaugeraete.com

• Niederlande/Netherlands
  service.NL@blaupunkt-einbaugeraete.com

• Belgien/Belgium
  service.BE@blaupunkt-einbaugeraete.com

• Schweden/Sweden
  service.SE@blaupunkt-einbaugeraete.com

• Frankreich/France
  service.FR@blaupunkt-einbaugeraete.com

• Luxemburg/Luxembourg
  service.LU@blaupunkt-einbaugeraete.com

• Schweiz/Switzerland
  service.CH@blaupunkt-einbaugeraete.com

• Italien/Italy
  service.IT@blaupunkt-einbaugeraete.com

• Spanien/Spain
  service.ES@blaupunkt-einbaugeraete.com

• Großbritannien/Great Britain
  service.GB@blaupunkt-einbaugeraete.com

• Malta/Malta
  service.MT@blaupunkt-einbaugeraete.com

• 00 800 32 289 000

• Australien/Australia
  CustomerCare@blaupunktAU.com

  • 1800 252 878 658

• Indien/India
  1800 209 2096

References

• www
• Blaupunkt Einbaugeräte: Blaupunkt

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>