BLAUPUNKT BPA-E604 4CH Class AB Amplifier Owner’s Manual
- May 15, 2024
- Blaupunkt
Table of Contents
BLAUPUNKT BPA-E604 4CH Class AB Amplifier
- PLEASE READ CAREFULLY BEFORE INSTALLING OR OPERATING THIS UNIT
WARNING
- Make sure you choose a suitable place to mount the unit.
- The position should be completely dry with a good circulation of air, and from a mechanical point of view very stable.
Specifications
Amplifier section
- Power output 40 (watts) 60W x 4CH
- Power output 20 (watts) 90W x 4CH
- Power output BTL (watts) 180W x 2CH
- THD: ≤0.1%
- frequency response (#2dB) 20Hz~20KHz
- signal-to-noise ratio ≥90dB
- sensitivity 0.2~6V
- recommended fuse type 25A x 2
- Dimensions 342mm x 204mm x 49mm
System planning
- Proper system planning is the best way to maximize your amplifier performance. By planning your installation carefully you can avoid situations where the performance of the reliability of your system is compromised.
- Your authorized dealer has been trained to maximize your system’s sonic potential. Your dealer is a valuable resource in helping you with your system design and installation.
Speaker requirements
- Each channel of your amplifier can easily drive 40 speaker loads when used in the stereo mode. When a channel-pair is bridged, the recommended minimum load impedance is 30 for subwoofer use and 42 for full-range operation. Although operation with lower impedances is not likely to cause immediate damage to the internal circuitry, the unit will most likely overheat, causing the thermal protection circuitry to shut down the amplifier.
- When the chassis cools down, normal operation will resume. Continuing to operate the amplifier under these conditions is not recommended and will reduce its life expectancy.
- Most speakers designed for car audio operation have 40 impedance. Connecting two such speakers in parallel will result in a 20-impedance load as seen by the amplifier. Some subwoofer models feature a dual 40-voice coil design. Connecting these voice coils in parallel will result in a 20 nominal impedance, which is not recommended for use with bridged channels of your amplifier.
Power Connection Leads
Notes on the power supply
Connect the + 12V power input lead only after all other leads have been
connected. Be sure to connect the ground wire of the unit securely to a metal
part of the car. A loose connection may cause a malfunction of the amplifier.
REMOTE: The unit is turned on by applying + 12 Volts to this terminal
This terminal does not draw heavy current like the two power terminals so a
thinner connecting wire is acceptable. Standard 18 GAUGE is fine and the
standard colour is yellow. If the radio is equipped with a power antenna
control wire, it can drive this terminal. If the power antenna wire is already
in use, you can still splice into it. With this method, the unit will turn on
automatically with the radio. Use the power supply lead with a fuse attached
whose value is the same as the original fuse. Place the fuse in the power
supply lead as close as possible to the car battery. During a full power
operation, Maximum current will run through the system. Therefore, Make sure
that the leads to be connected to the + 12v and GND terminals of the unit
respectively must be larger than 10-Gauge (AWG. 10).
system 1: 4-channel mode
system 2: 3 channel mode
system 3: 2-channel bridged connection
Power Connection Leads
- BP Americas Corp. 9590 NW 40th
- St. RoadDoral, FL 33178
- www.blaupunkt.com
Documents / Resources
|
BLAUPUNKT BPA-E604 4CH Class AB
Amplifier
[pdf] Owner's Manual
BPA-E604 4CH Class AB Amplifier, BPA-E604, 4CH Class AB Amplifier, Class AB
Amplifier, AB Amplifier, Amplifier
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>