Xtrfy MZ1W-RGB Wireless Ultra Light Gaming Mouse Instruction Manual
- June 5, 2024
- Xtrfy
Table of Contents
Xtrfy MZ1W-RGB Wireless Ultra Light Gaming Mouse
Function layout
- Left Left click
- Right-click
- Middle-click
- Forward
- Backward
- Setting
- Scroll up
- Scroll down
- Profile
- Power Off
- DPI Mode
- RGB Mode
- PGDN Mode
- Type-c connection
Instruction
Mouse instruction:
- Take out the wireless USB Nano receiver from package
- Plug the receiver into your computer USB port
- Turn on the mouse power by switching the power switch on the bottom of the mouse
- Waiting for computer installation finished
DPI setting and indication:
- DPI level: 400-800-1200-1600-3200-4000-7200-19000, total 6 levels DPI
- By pressing the setting button on the top of mouse when the mode switch is in DPI mode to change DPI circularly
Polling rate:
125(red)-500(blue)-1000Hz(green)
The mode switch and setting function:
- The setting button is a DPI change function when the mode is in DPI mode
- The setting button is an RGB setting function when the mode is in RGB mode
- Setting button is a PGDN function when the mode is in PGDN mode
- Power off the mouse when the mode SWitch is in Power oft mode
Wired and wireless function:
- Wired and wireless mode switch automatically when you plug the receiver into a computer without a cable connection, it will work as wireless mode.
- If you connect the cable from the computer to the mouse, it will switch to wired mode automatically and work as wired mode.
Low power and charging indication
- .Low power indication: when mouse battery power is low, the Red color will blink, you need charge the mouse
- During charging the yellow color led will blink, after the battery charging ful, the LED color will back to the previous normal RGB effect.
Pairing
Use the pairing tool to pair the mouse and receiver if lost connection or
change to new receiver
About shape change and weight balance adjustment:
- Unscrew the back cover to change different shape back shell
- Take out the button from the end to change the button
- Unscrew the battery screw under the mouse to move the battery forward or backward to adjust the mouse balance
Main Specification
- Size 111.6×59.6×36.6mm
- Weight Around 61g
- Switch Kailh GM8.0
- Sensor PAW3370
- Max DPI 19000
- Default DPI: 400-800-1200-1600-3200-4000-7200-19000DPI
- IPS 400ips
- Acceleration 50g(Max)
- Polling rate 125-500-1000Hz
- Interface USB 2.0
- Battery type Li-ion Polymer Battery
- Battery Capacity 500mAh
- Charging time Around 2h
- Input 5VDC 0.5A
- Battery 3.7VDC 500mAh
CAUTION
- Keep the battery dry.
- Avoid locating the battery terminals near metallic object.
- Do not short-circuits and avoid metallic or water come into mouse to cause battery short
- Use computer USB and specifed cable to charge the mouse
SHENZHEN F&G ELECTRON CO., LIMITED
Bldg 6, Tongfang Creative Park, Shajing, Bao’an District, Shenzhen, China.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>