BLAUPUNKT RVC701 Robot vacuum cleaner with washing function Owner’s Manual

RVC701 Robot vacuum cleaner with washing function
Owner’s Manual

IMPORTANT NOTES

• Before using this device read the instruction manual and follow the instructions inside. The manufacturer is not liable – for any damages caused by the misuse of this device due to inappropriate handling. Please keep this manual for future Irefetence.
• This device is for domestic use only. Do not use it for any other purposes.
• The device should be cleaned regularly complying with the recommendations described in the section on cleaning and maintenance.
• Do not place the device near sources of heat, flame, an electric heating element, or a hot oven. Do not place it on any other device.
• ‘This equipment can be used by children aged 8 years and over as long as supervision is provided. People with reduced physical or mental capabilities, as well as people with no previous experience in using this equipment, must be Istipeirvised and made aware of the risks. The instruction manual should be used as a reference for the safe use of this equipment. Children should not play with the equipment.
• Children without ensured supervision should not be allowed to perform the cleaning and maintenance of equipment.
• Additional precautions should be taken when using this device in the presence of children or pets. Do not allow children to play with the device.
• Never use the product close to combustibles.
• Never expose the product to atmospheric conditions such as direct sunlight or rain, etc… Never use the product in humid conditions (like a bathroom or camping house).
• Only Original accessories should be used, as well as accessories recommended by the manufacturer. Using accessories that are not recommended by the manufacturer may result in damage to the device and may render the device unsafe for use.
• The AC adapter should be connected to an outlet with characteristics consistent with the values on the rating label.
• If the cord or power plug or adaptor is damaged or the plug has a loose electrical outlet, do not charge the device and do not power it from the mains.
• Unplug the AC adapter from the electrical outlet when not in use.
• Do not connect or disconnect the adaptor from the power source with wet hands. Do not vacuum without first ensuring that filters are installed correctly.
• You cannot vacuum very fine dust such as flour, cement, gypsum powder, toners, or dirt that may be hot, such as ash, cigarette butts, and matches.
• You should use the vacuum cleaner to clean dry surfaces only.
• DO not use the vacuum cleaner on damp and wet cleaned carpets and flooring.
• Do not place any objects on or add any load to the vacuum cleaner. Pay attention to children and animals when the vacuum cleaner is working (so that it is not lifted, hit, or sat on). Before starting the vacuum cleaner, make sure that all external doors are closed (the vacuum cleaner can only be used at home).
• Before starting the vacuum cleaner, make sure that all external doors are closed (the vacuum cleaner can only be used at home).

Conformity
Heteby,SlaupunktCompetence-Center 2NrEverpol_Sp. zo.o.rdeclares_that this equipments in compliance with the essential requirement and other relevant provisions of Directive 2014/53/EU. Declaration of conformity can be obtained from the product page at www.blaupunkt.com.
Responsible party: 2N-Everpol Sp. z o.o, Putawska 403A, 02-801 Warsaw, Poland, Phone: +48 22 331 99 59, E-mail: info@everpol.pl
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.
Your product contains batteries covered by the European Directive 2006/66/EC, which can not be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer), and polyethylene (bags, protective foam sheet). Your system consists of material that can be recycled and reused if disassembled by a specialized company. Please observe the local regulations, regarding the disposal of packaging materials, exhausted batteries, and old equipment.
Your products are designed a manufactured with high-quality materials and components, which can be recycled and reused.

**DEVICE SPECIFICATIONS

**

Voltage:24V
Amperage: 600mA
Set of brushes and filters: Blaupunkt ACC045
Battery: Li-ion, 2150mAh
POWER-SUPPLY SPECIFICATIONS
Out voltage: 100-240V-50/60Hz
Input Amperage: max. 400mA
Otlitplut voltage: 24V
Output Amperage: 600mA

1. Control panel
1a. Power button
1b. HOME button
lc. PLAN button
1d. Display
2. Large pull-out dust bin
2a. Bin cover
2b. Bin opening lock
2c. NEPA filter
2d. Prefilter
3. Pull-out dust bin with an integrated water tank
3a. Water inlet
3b. Water pump
3c. Dust bin handles
3d. Dust bin latch
3e. NEPA filter
4. Bumper
5. Front-wheel
6. Drive wheels| 7. Collector brushes
8. Suction opening
9. Main collector brush
10. Main collector brush cover
11. Surface-edge sensors (Anti-fall)
12. Main switch
13. Charging socket
14. Robot charging connectors
15. Charging station
16. Remote control
16a. Display
16b. HOME button
16c. Direction buttons (allow the robot to move in the indicated directions; only works in standby mode)
16d. MAX button
16e. CLK button – sets the robot’s timer
16f. PLAN button – allows you to schedule the robot’s operating hours
16g. ON/OFF button – once pressed, the robot starts cleaning or enters standby mode
16h. MODE button – allows you to select the operating mode
---|---

BEFORE FIRST USE

1. Remove all the paper, carton, and foil protecting the vacuum and its parts.
2. Install the collector brushes. Press the brush marked with L or R into the appropriate location marked L or R.
3. Make sure that the main collector brush is installed correctly.
4. Put; the dust bin in the robot.
5. Place the charging station in a convenient location and connect it to the mains. It is recommended to leave free space around the station, 1 meter to the sides and 2 meters at the front.
6. Charge the device battery according to the instructions.

CHARGING THE DEVICE

1. Plug the power supply plug into the charging station, then plug the power supply into an electrical socket. A blue LED will indicate that the station is correctly connected.
2. Switch the vacuum cleaner on with the main switch.
3. Place the robot vacuum cleaner on the charging station so that the charging connectors touch the corresponding plates on the charging station.
4. The display will show”1111″ indicating that charging is in process.
5. When Charging is complete, the display will show”FULL”.

Tips:
The first Charging should take 12 hours.
Charge the robot as soon as possible after the battery has been discharged. If the robOt is not to be used for a long time, make sure the battery is not discharged.

ROBOT ACTIVITY MODES (STATES)
– oft the robot is switched off with the main switch and does not consume power. It will not charge in the charging station.
– standby state: this state will be reached after the robot is stopped by using the on/off button or the robot is woken up from sleep with the on/off button
– sleep state: the robot will automatically go to sleep after two minutes of inactivity or 10 minutes if it is connected to WiFi and the application is not being used.
Battery power consumption in sleep mode is reduced. Press and hold the on/off button for 6 seconds to enter sleep mode.
DEVICE START-UP
Prepare the surface of the room to be cleaned. Remove sensitive objects, cables, and sheets of paper. Raise backdrops, curtains, and drapes hanging on the floor. Cover delicate furniture.
Press the power button to start the robot vacuum cleaner. The robot will start to move and vacuum in agtomati4 mode.
You can change the vacuum modes with the remote control when the vacuum cleaner is in standby mode or vacuuming. Press the Mode button to change the vacuum mode.
1111 —Cleaning along the edges
2222 — spot cleaning
3333 —Zigzag mode
4444 — Automatic cleaning
The vacuum power can be changed by pressing the MAX button on the remote control.
CONTROLLING THE ROBOT

1. Remote robot control When the robot is in standby mode, it can be moved by pressing the arrow buttons on the remote control, corresponding to the directions of movement.

2. Programming the schedule using the robot’s control panel
   A. Setting the robot’s system clock
   A1. Press the”PLAN” button, the robot will display the currently set time.
   A2. Two left digits will start flashing (hour). You can increase their value by pressing the”HOME” button. Press the power button to set the minutes.
   A3. Two right digits will start flashing (minutes). You can increase their value by pressing the”HOME” button.
   A4. Press the power button to save the changes. Press the”PLAN” button to exit the time setting mode.
   B. Setting the scheduled cleaning time
   Bl. Hold the”PLAN” button for 5 seconds. The last two digits will start flashing.
   B2. Select the schedule number by pressing the”HOME” button. Each press of the”HOME” button will increase the value by one. Confirm with the power button .
   B3. Then set the desired hour and minutes.
   B4. Press the power button to save the changes. Press the”PLAN” button to exit the schedule setting mode.
   NOTES:
   1. In order for the cleaning schedule to function properly, it is necessary to program the robot’s internal time.
   2. The robot will start cleaning at the scheduled time every day.
   3. After turning the robot off with the main switch, the time and schedule settings will be reset.
   4. To delete the schedule, set the time to 00:00.

3. Programming the schedule using the remote control
   3a. Press and hold the”PLAN” button on the remote control for 5 seconds
   3b. Use the arrow buttons to set the scheduled time
   3c. Press the”ON/OFF” button to confirm the scheduled time. The robot’s display will show the set time.

Note: by setting the time on the remote control, you set the start delay in relation to its system time.
For example,  the time indicated on the remote control is 01:30 AM, the robot’s internal time: is 08:00 AM, and the schedule will be set to 09:30 AM every day.
USING THE VIRTUAL WALL (MAGNETIC STRIP)
To reduce the robot’s operating area, you can place the magnetic strip, which will create a virtual wall. As the robot approaches the strip, it will recognize it, makes a turn, or turns around. The strip can be placed in the passageway between rooms or used to separate the device from cables or bowls for pets.
CONNECTING THE DEVICE WITH THE WIFI NETWORK AND APPLICATION
Note: The robot only uses a 2.4 GHz network. Make sure the router provides this connection. Install the BlueBot APP on your phone. It is available from Google Play or the Apple store. You can also scan the following code to load the appropriate link:
QR

https://apps.apple.com/us/app/blaubot- app/id1478086780?l=zh&ls=1

https://play.google.com/store/apps/details?id=com.blaubot.bot

Next, follow the instructions shown in the application:

1. Register a user account
2. Select the compatible model
3. Reset the vacuum cleaner connection parameters by pressing and holding the home button for 3 seconds
4. The application will ask you to enter the name of the WiFi network and the network access password
5. Connect the phone directly to the network generated by the robot named”RVC_xxxx”
6. If the robot establishes a network connection, a message will appear on the display saying “CONN”.

In case of an error message, repeat the connection procedure by entering the correct network parameters.
The application allows you to control the basic functions of the robot and monitor its operation. The application contains a detailed user manual for the application.

CLEANING AND MAINTENANCE

1. Emptying and cleaning the dust bin:
   Pull out the bin. Remove the cover and the internal filter. Empty the bin. The bin may be cleaned under running water (do not wash in a dishwasher or washing machine). Clean the filter with a soft brush.

2. Cleaning the device body
   Clean the device with a damp cloth, and then wipe it dry. Do not immerse the device in water. Regularly remove any dirt that might block the air intake opening and sweeping brushes.

LIST OF MESSAGES:

1| E2| The main switch is off, the battery cannot be charged
2| E3| Supply voltage too low or automatic recharging of the battery is not possible
3| E11| Left surface sensor error
4| E12| Right surface sensor error
5| E13| Central surface sensor error
6| E21| Left wheel suspension error
7| E22| Right wheel suspension error
8| E23| Central wheel suspension error
9| E31| Left bumper sensor error
10| E32| Right bumper sensor error
11| E33| Central bumper sensor error
12| E41| Left wheel overload error
13| E42| Right wheel overload error
14| E43| Left sweeping brush overload error
15| E44| Right sweeping brush overload error
16| E45| Motor fan overload
17|  E46| Main collector brush overload error
18| Lo| The low battery charge level
19| 11:11| Charging in progress
20| FULL| Battery charged
21| CONN| Establishing WWI connection
22| FAIL| Error in establishing WiFi connection
23| SUCC| WiFi connection successful

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>