Genius NX-7000 Wireless Optical Mouse User Guide
- June 5, 2024
- GENIUS
Table of Contents
Genius NX-7000 Wireless Optical Mouse
OVERVIEW
Hardware Installation
- You can connect the receiver to a USB port of a PC.
- Install one AA battery in the mouse as instructed.
- Make sure that you have switched on the power switch underneath the mouse.
Factory Settings
- Left Button: Provides traditional mouse functions like click, double click and drag.
- Magic-Roller: Press the “Magic-Roller” to surf the Internet and Windows documents.
- Right Button: Provides traditional mouse click functions.
Warning: (Troubleshooting)
- Do not use the wireless opticalllaser mouse on a desk which is made of glass or mirror.
- The connection of the wireless device is factory preset, so when you plug the USB receiver into any USB port, the connection between the micro receiver and the mouse will be established automatically.
- In case your PC did not install the hardware successfully, remove the micro receiver from the USB port and go Human Interface Devices under Device Manager to remove the mouse then plug in the micro receiver to a USB port again.
- If you feel the mouse does not move smooth as usual, it is possible the batteries have lost their charge so you need to replace them. Remember to put the batteries in the correct direction.
Federal Communication Commission interference statement:
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installations. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures Reorient / Relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected. Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following tWO Conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning: The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Disclaimer The following does not apply to any country where such provisions are inconsistent with local law: KYE Systems Corp. makes no warranties with respect to this documentation, whether expressed or implied. All material is provided “as is”. This includes, but is not limited to, any implied warranties of merchantability and fitness is for a particular purpose. The information covered in this document is subject to change without notice. KYE Systems Corp. assumes no responsibility for any errors that may appear in this document. All brand names mentioned in this manual are trademarks or registered trademarks of their respective companies.
CE Declaration of Conformity
The following designated product: Wireless Mouse: NX-7000 M/N: GM-150002/T, GM-1500002/R is herewth contirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States, relating to R&TTE Directive (99/5/EC). For the evaluation regarding the electromagnetic compatibility, the following standards were applied: EN 300 440-1 EN 300 440-2 EN 301 489-1 IEN 301 489-3 EN 60950-1 This declaration is prepared for the manufacturer: KYE SYSTEMS CORP. #492, Sec. 5, Chongxin Rd., Sanchong Dist., New Taipei City 24160,Taiwan, R.O.C.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>