Leica FLX100 Smart Antenna User Guide
- June 5, 2024
- Leica
Table of Contents
Leica FLX100 Smart Antenna
Important Information about your Instrument
Read and follow the User Manual from the myWorld web page before using the
product.
myWorld@Leica Geosystems https://myworld.leica-geosystems.com
Keep for future reference!
Intended use
- Measuring raw data and computing coordinates using carrier phase and code signal from GNSS satellites (GNSS systems).
- Computing with software
- Recording measurements
- Recording GNSS and point related data
- Carrying out measurement tasks using various GNSS measuring techniques
- Data communication with external appliances
The product must not be disposed with household waste.
For the AC/DC power supply and the battery charger:
WARNING
Unauthorised opening of the product
Either of the following actions may cause you to receive an electric shock:
- Touching live components
- Using the product after incorrect attempts were made to carry out repairs.
Precautions:
-
Do not open the product!
-
Only Leica Geosystems authorised service centres are entitled to repair these products
-
FCC Part 15 (applicable in US)
-
Hereby, Leica Geosystems AG declares that the radio equipment type
FLX100 smart antenna is in compliance with Directive 2014/53/EU and other applicable European Directives. The full text of the EU declaration of conformity is available at the following Internet address: http://www.leica- geosystems.com/ce.
Class 1 equipment according to European Directive 2014/53/EU (RED) can be placed on the market and be put into service without restrictions in any EEA member state. -
The conformity for countries with other national regulations not covered by the FCC part 15 or European Directive 2014/53/EU has to be approved prior to use and operation.
Trademarks
- Bluetooth® is a registered trademark of Bluetooth SIG, Inc. All other trademarks are the property of their respective owners.
Instrument Components
Description
a Connection LED
b Data link LED
c Satellite LED
d Battery LED indicator
e Power button f USB type-C port
Technical Data
Power
| Internal battery | 3.8 V, 6120 mAh Type-C charging, support 1.44 A fast charge |
|---|---|
| Input voltage | 5 V DC/2 A |
| Power consumption | 1.8 W |
| Working time | Up to 10 hours (post processing) Up to 8 hours (RTK with GSM) |
| Charge time | Typically 6 hours |
Environmental spHFLfiFDtLons
| Type | Operating temperature [°C] | Storage temperature [°C] |
|---|---|---|
| Instrument | −30 to +65 | −40 to +80 |
| External LnfluHnFHs | Protection | |
| --- | --- | |
| Water, dust and sand | IP67 | |
| Humidity | Up to 100% (non-condensing) | |
| Shock resistance | Designed to endure to a 2 m pole drop and 1.2 m free drop on |
concrete floor with no damage
Care and Transport
Care and transport
Carry the product in its original container to protect the product against
shock
and vibration.
Operation
The battery must be charged before using it for the first time.
Turning on/off the instrument
Turn on:
Press and hold the power button until the battery LED goes green and the
device sounds a beep.
Turn off :
Press and hold the power button until the battery LED goes out and the device
sounds a beep.
a Power on/off button
b Battery LED indicator
Connect the Handheld to Receiver by Bluetooth
Step-by-step
Follow these steps to connect the handheld to the instrument by Bluetooth.
- Open the Bluetooth settings on your device.
- Search for your FLX100 smart antenna with its serial number.
- Find target FLX100 smart antenna serial number.
- Push Connect.
Connect the Handheld to the Pole
Step-by-step
Follow these steps to connect the handheld to the pole.
-
Use a slot screwdriver to fi[ the pole adapter with both screws to the FLX100 smart antenna.
Make sure to fi[ the adapter in the correct orientation. -
Screw the pole clockwise into the adapter.
922524-1.0.0en
Original text (922524-1.0.0en)
Printed in Switzerland
© 2020 Leica Geosystems AG, Heerbrugg, Switzerland
www.leica-geosystems.com
FCC warning statements:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
IC warning statements:
-English Warning Statement:
“This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.”
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B)
-French Warning Statement:
This device meets the IC radiation exposure limits for uncontrolled environments and rss-102 of IC radio frequency (RF) exposure rules. The device has a very low RF energy level and has been evaluated (SAR) tested within the allowable range.
References
- When it has to be right | Leica Geosystems
- CE Conformity Declarations | Leica Geosystems
- myWorld @ Leica Geosystems