Leica DROP XL Wireless Charger User Manual
- October 30, 2023
- Leica
Table of Contents
DROP XL WIRELESS CHARGER
USER MANUAL
WHAT IS INSIDE
SPECIFICATION
Drop XL Wireless Charger
(Model No.: DROPXL01 )
Power Supply:
Input 100-240V ~ 50/60Hz 1.5A,
Output 15V 3A
Qi Wireless Charger:
Output 10W (max per pad)
Frequency 127.7 kHz
Maximum Field Strength 11.57 dBµA/m
Charging Distance: ≤2 mm
USB-A Port: Output 5V 2.4A
AirPods Charging:
Make sure the AirPods or AirPods Pro case is placed on the center of the
charging area. The white status LED may blink or switch off repeatedly while
charging – this does not affect the charging progress.
AirPods Pro charging status can be checked by tapping on the case. If the LED
lights up orange, charging is still in progress. If the LED lights up green,
charging is complete. A full charge takes 3-5 hours. 
HOW TO INSTALL
LED INDICATION
White light
Red light flashing
Charging
Foreign object detected (e.g. metallic object)
| FCC responsible party: TianHeng Consulting, LLC
392 Andover Street, Wilmington, MA 01887, United States
Telephone +1 213-397-2158 Email:
support@nativeunion.com|
---|---|---
FCC Statement (US Customers only)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
WARNING: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment of fand on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. FCC ID:
X3QDROPXL01, X3QDROPXLW01
RSS Statement (Canada)
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 10cm between the radiator and your body. IC: 23711-DROPXL01, 23711-DROPXLW01
SAFETY INFORMATION
- This product is intended for home, office & IT equipment use.
- For indoor use only.
- Consult local staff before using the product near medical or industrial equipment or on board an aircraft.
- Prevent cables from being pinched or damaged.
- A damaged cable or device may malfunction and / or overheat. (Fire hazard)
- Unplug the product if not used for an extended period of time.
More information
leica-camera.com/wireless-charging-pad#product-documentation
EUROPE – DECLARATION OF CONFORMITY EU / UK
Hereby, Design Pool Limited declares that the product DROPXL01 is in
compliance with Directive 2014/53/EU as well as UK Radio Equipment
Regulations. The full text of the EU/UK DoC is available online:
nativeunion.com/product-documentation
Manufacturer:
Design Pool Limited, 33/F, 88 Hing Fat Street, Hong Kong / Design Pool SAS,
146 Rue Montmartre, 75002 Paris, France –
support@nativeunion.com
Made in China
© 2023 Native Union all rights reserved. Native Union is a registered
trademark of Design Pool Limited.
Trademarks and trade names are those of their respective owners. Copyright
Design Pool Limited.
ONLINE_DROP-XL-LEICA_IM_1.0
nativeunion
nativeunion
native_union
nativeunion.com
References
- Drop XL Wireless Charger | Leica Camera US
- Tech Accessories Reimagined | Native Union
- Product Documentation