Shenzhen LA-WE2S WIFI Module User Manual
- June 5, 2024
- Shenzhen
Table of Contents
Shenzhen LA-WE2S WIFI Module
Product Overview
LA-WE2S is a Low-Power Embedded WiFi module. It is composed of a highly integrated radio frequency chip TR6260S1 and a small number of peripheral devices, with built-in WiFi network protocol stack and rich library functions. LA-WE2S is embedded with low-power 32-bit microcontroller, 1Mbyte flash memory and rich peripheral resources. Users can develop embedded WiFi products to meet their own needs based on these.
Product Characteristics
- 2.4GHzIEEE802.11b/g/n
- Adopt low power 32-bit CPU, and the main frequency is up to 160MHz
- Support STA / AP working mode
- Support WEP/WPA-PSK/WPA2-PSK
- Support SmartConfig with one click distribution network
Main Application Fields
- All kinds of electrical occasions
- It is used in such scenes as switching socket, wall switch, wall socket and circuit breaker, and supports voice control and Amazon cloud voice.
- The TYWE2S module compatible with pin2pin graffiti
Overall Dimension
PCB Package
Size
Pin Definition
| TOP | Bottom | |
|---|---|---|
| No. | Name | Illustration |
| 1 | RST | Low level reset |
| 2 | NC | N.C. |
| 3 | GPIO13 | Digital IO |
| 4 | GPIO4 | Digital IO |
| 5 | GPIO22 | Digital IO |
| 6 | GPIO0 | Digital IO |
| 7 | GPIO1 | Digital IO |
| 8 | U1TX | UART1_TX and Digital IO |
| 9 | U1RX | UART1_RX and Digital IO |
| 10 | GND | Power ground |
| 11 | VDD | Power 3.3V |
Electrical Parameters
Absolute electrical parameters
| Parameters | Description | Minimum | Maximum | Unit |
|---|---|---|---|---|
| TS | Working temperature | -20 | 85 | ℃ |
| VDD | Supply voltage | -0.3 | 3.6 | V |
Working conditions
Parameters| Description| Minimum| Typical| Maximum|
Unit
---|---|---|---|---|---
VDD| Working voltage| 3.0| 3.3| 3.6| V
VDDIO| IO voltage| 1.8| 3.3| 3.6| V
VIL| IO low level input| -0| –| 0.3VIO| V
VIH| IO high level input| 0.7VIO| –| VIO| V
VTH| COMS threshold| –| 0.5 VIO| | V
Imax| IO maximum drive| | | 12| mA
Power consumption in operation mode
| Working mode | Working status, Ta=25℃ | Average | Unit |
|---|
Fast connect distribution network
status
| The module is in the state of fast connection distribution network, Wi-Fi
indicator light flashes quickly| 120| mA
Hot spot distribution
network status
| The module is in hot distribution network state, Wi-Fi indicator
light flashes slowly
| 122| mA
Network connection
status
| The module is in the networking state, and the Wi Fi indicator is
always on
| 105| mA
Networking attempt| The module is in the working state of disconnection
(trying to
connect to the network), and the WiFi indicator is always off
| 110| mA
---|---|---|---
RF Characteristics
Basic RF characteristics
| Parameter item | Detailed description |
|---|---|
| Working frequency | 2.412~2.462GHz |
| WiFi standard | IEEE 802.11b/g/n(Channel 1-11) |
| Data transmission rate | 11b:1,2,5.5,11 (Mbps) |
11g:6,9,12,18,24,36,48,54(Mbps)
11n:HT20 MCS7
Antenna type| PCB antenna (default)
WiFi output power
TX continuous transmission power
Parameter| ****
Minimum
| ****
Typical
| Maximu
m
| Unit
---|---|---|---|---
Mode| Rate| dBm
RF average output
power,802.11b CCK
| ****
11M
| ****
–
| ****
18
| ****
–
| ****
dBm
RF average output
power,802.11g
| ****
54M
| ****
–
| ****
16
| ****
–
| ****
dBm
RF average output
power,802.11n
| ****
HT20-MCS7
| ****
–
| ****
14
| ****
–
| ****
dBm
Frequency error| -10| –| 10| ppm
WiFi receiving sensitivity
RX receiving sensitivity
Parameter| ****
Minimum
| ****
Typical
| Maximu
m
| Unit
---|---|---|---|---
Pattern| Rate| dBm
RF average output
power,802.11b CCK
| ****
11M
| ****
–
| ****
-88.0
| ****
–
| ****
dBm
RF average output
power,802.11g
| ****
54M
| ****
–
| ****
-74.0
| ****
–
| ****
dBm
RF average output
power,802.11n
| ****
HT20-MCS7
| ****
–
| ****
-70.6
| ****
–
| ****
dBm
Frequency error| -10| –| 10| ppm
Application schematic diagram
**Application of breaker
**
Non-metering version of smart socket
Single indicator application
Dual indicator application
Metering version smart socket
Single indicator application
Dual indicator application
Application Scenarios
- Support all kinds of intelligent lamps and sockets
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Please notice that if the FCC identification number is not visible when the
module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following:
“Contains FCC ID:2AXJE-LA-WE2S” any similar wording that expresses the same
meaning may be used.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter. The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install module.
A separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and difference
antenna configurations.
There is requirement that the grantee provide guidance to the host
manufacturer for compliance with Part 15B requirements.
The OEM integrator is responsible for ensuring that the end-user has no manual
instructions to rem-ove or install module.
The module is limited to installation in mobile or fixed application.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>