Shenzhen Goalsun Optoelectronics Technology Co Ltd GV008 Smart Motion Sensor Security Lights User Manual

Shenzhen Goalsun Optoelectronics Technology Co Ltd GV008 Smart Motion

Sensor Security Lights

Prior to the installation, service or routine maintenance, please read the following general precautions.

SAFETY INSTRUCTION

1. DO NOT install the fixture near an air condition unit or flammable materials.
2. DO NOT install it in a place with limited ventilation, high vibration levels, or high ambient temperatures.
3. DO NOT look directly at the light source when it is on, as this may cause irreparable damage to the eyes.
4. Risk of suffocation! Keep small parts and packaging materials away from children.
5. Non-professionals are forbidden to disassemble, repair, or modify this product.

SPECIFICATIONS

PRE-INSTALLATION

1. Mounting Height and Locations.

• Keep the fixture level with the ground.
• Leave at least 1 D cm apace from the top or ceiling and side wall.
• Install the fixture on a flat surface and a relatively stable piece.
• Optimum installation height: 2.5 m(S.25 ft)

Mounting Accessories

lnstallatlon Procedure

1. Install the Iron Plate (A) on the junction box In right direction and tighten it with screws (BJ.
2. Remove the Wiring Cover (GJ from the light.
3. There is a rubber plug in the hole (HJ, drill a hole in the rubber plug and lead the electric wires from the junction box through the hole (HJ. Remove the silicone plug amid the Wiring Cover (G), then install the Wiring Covar (GJ on the junction box and tighten it with a screw (CJ. Then cover the hole with a silicone plug.

Wlrlng the Light Fixture

CAUTION; Make sure the connection Is correct as shown below.

• The ends of the mains cable should leave enough length to make it easy to make connections.
• Connect the mains cable to the Connector Block.
• Insert the white/blue wire from the original power supplier into the terminal marked “N”.
• Insert the black/brown wire from the original power supplier into the terminal marked “L’.
• Insert the green/yellow earth wire from the original power supplier into the terminal marked “ .
• Mount the light fixture (Fl on the Wiring Cover assembly, tight it with screw (D), and cover it with silicone plug(E).

OPERATION

Lamp Heads Adjustment

• The left and right lamps can be adjusted 90 degrees up or down.
• The left and right lamps can be adjusted 90 degrees backward or forward.
• The triangle bracket can be adjusted 45 degrees left or right.

Motion Senaor AdJuatment

The sensor can be adjusted 90° degrees left or right.

Detection Range

*Detection Range: around 72 ft/21m 180 degrees (Max.)**

Custom Settings

SOFTWARE INSTALLATION

1. Scan the QR code below to download the App, or search “SOLLA” in App Store (iOS) or Google Play Store (Android) to install the app.
2. 0pen the App, click”Start Now” to log in to the APP as a visitor. (Note: Login account can get more functions.)

REGISTRATION

1. Click ‘Create an account’.
2. Choose your region, enter your email, and click ‘Verification code’ .
3. You will receive an email with a verification code, and please enter the verification code.
4. Set your password to finish registration.

ADDING DEVICES

Warm-up time

1. When the light is powered on the first time, it will light on for 45 seconds, this is the ‘warm-up time•. Please wait until the light turns off, then it will change to “TEST mode’ and begin to work.
2. When the security light is re-energized, it will light on for 45 seconds. Alter waiting for the lights to go out, it will return to the mode of the last power outage and start working.

Pairing/Factory RHat
Press and hold the “DIST” button of the light fixture for 5 seconds, the indicator will flash blue 3 times, which means the reset completes. (Note: the reset will fail if you press the DIST button less than 5 seconds)

Adding by Auto-Search

1. Click”+” and click “Add device”.
2. Wait for the automatic scan for devices.
3. Click the device if you see it.

Adding by selecting Models

1. CIiek. +” and CIiek “Add device”.
2. Select the device model you need to add. (For example: if you select model A28, only this model can be added to the network.)

About Bluetooth Pairing Failures

1. Make sure the device is powered on.
2. Make sure Bluetooth is turned on.
3. Make sure the network on your phone is working.
4. Please make sure that the device is within the signal coverage of cell phone Bluetooth, the closer the distance the easier the pairing.
5. Please reset the device and try again.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

Caution: Changes or modifications to this unit are not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equip
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

EU Declaration of Conformity

We SHENZHEN GOALSUN OPTOELECTRONICS TECHNOLOGY CO., LTD.hereby, declare that this equipment is in compliance with the applicable Directives and European Norms, and amendments.

ISED Statement

English: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license- exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

• This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>