SENA SP79 Wi-Fi Adapter User Manual
- June 5, 2024
- Sena
Table of Contents
User Manual
WiFi Adapter Manual
Introduction
WiFi Adapter is a device for SENA Bluetooth that charges and provides auto
firmware upgrade.
WiFi Adapter can automatically connect to the router through the mobile app,
automatically download the latest firmware available for SENA Device, and can
always upgrade to the latest firmware by comparing firmware versions when the
user plugs SENA Device into the USB port to charge.
WiFi Adapter features
- Supports WiFi-related IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
- Smartphone App for iPhone and Android
- Firmware upgradeable
Contents
– Wifi Adapter
Product description
Getting started
a. Power On:
Insert the USB port into the charger and insert the Micro USB Port into the
“USB power port”
b. Connecting to WiFi
- Open the mobile app
- Connect to WiFi Docking
- Setting WiFi Docking Station configuration
- Select the WiFi router to connect to
- Enter the password of the selected WiFi router and click “Connect”
- WiFi Adapter is connecting to the router.
- Click “Setup Complete” when connected
- After following these steps, WiFi Adapter should be connected to WiFi. “WiFi status” LED will show blue light if the WiFi router is connected successfully and show a red light if there has been a failure to connect.
- To change the router connection, repeat the steps above.
- You can update Sena devices such as 30K manually and update WiFi Docking Station
c. Charging SENA Bluetooth device
Plug in the Micro USB to sena Bluetooth device to charge the device. The
“Charging status LED” will show red light while charging and turn blue when
the device is fully charged.
d. Upgrading Firmware
The firmware will be upgraded automatically while charging 30K through
checking the firmware version and downloading the latest firmware available.
“Firmware upgrade status” LED will show blue light when the upgrade is
finished and blink while the firmware is upgrading.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the condition that this device does not cause harmful interference (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body: Use only the supplied antenna.
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Manufacturer’s Name: Sena Technologies, Inc.
Address: 19, Heolleung-ro 569-Gil, Gangnam-gu, Seoul, South Korea
Product name: WiFi Adapter
Model number: SP79
Operating Temperature: -10° C to 80° C
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 20mm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna. This device
is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. All essential radio test suites have been carried
out.
- CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
- DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION
- The product shall only be connected to a USB interface of version USB 2.0
- The device complies with RF specifications when the device is used at 20mm from your body
RF POWER
| Function | Operation Frequency | Max RF output power: | Limit |
|---|
WIFI 802.11b/g/n(HT20,HT40)
2.4G| 802.11b/g/n(20MHz): 2412~2472MHz;
802.11n(40MHz):2422~2462MHz| 14.05dBm| 20 dBm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>