baby trend BC20xxxS Smart Steps EZ Bouncer Instruction Manual
- June 12, 2024
- baby trend
Table of Contents
KEEP INSTRUCTIONS FOR FUTURE USE.
BC20xxxS
BC20xxxS Smart Steps EZ Bouncer
WARRANTY
DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR
REPLACEMENT PARTS, SERVICE AND REPAIR.
The Baby Trend® warranty covers workmanship defects within 1 year of purchase.
Any product which has been subjected to misuse, abuse, abnormal use, excessive
wear and tear, improper assembly, negligence, environmental exposure,
alteration or accident, or has had its serial number altered or removed
invalidates all claims against the manufacturer. Any damage to property during
installation is the sole responsibility of
the end user.
Customer Service Department can be contacted at 1
800-328-7363 Monday through Friday
between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required
prior to returning product(s) to Baby rend®. Please visit
http://babytrend.com/pages/ limited-warranty for complete warranty details.
GARANTIA
NO DEVUELVA SU PRODUCTO A LA TIENDA. POR FAVOR CONTACTE A BABY TREND® PARA
PIEZAS DE REPUESTO, SERVICIO Y REPARACION.
Baby Trend, Inc. 13048 Valley Blvd. Fontana CA 92335
1-800-328-7363
(8:00am ~ 4:30pm PST)
www.babytrend.com
WARNING
WARNING! Not intended for infant sleep and should never be used for this
purpose.
FALL HAZARD: Babies have suffered skull fractures falling while in and from
bouncers.
-
Use bouncer ONLY on floor.
-
ALWAYS use restraints. Adjust to fit snugly.
-
NEVER lift or carry baby in bouncer.
SUFFOCATION HAZARD: Babies have suffocated when bouncers tipped over on soft surfaces and/or when bouncers have been used as a sleep product. -
NEVER use on a bed, sofa, cushion, or other soft surface.
-
Stay near and watch baby during use. This product is not safe for sleep or unsupervised use.
If baby falls asleep, remove baby as soon as possible and place baby on a firm, flat sleep surface such as a crib or bassinet.
TO PREVENT FALLS AND SUFFOCATION:
- ALWAYS use restraints. Adjust to fit snugly.
- STOP using bouncer when baby starts trying to sit up or has reached 20 lb (9 kg), whichever comes first.
- Toy bar is NOT designed to be used to as a carry handle.
- NEVER use on any elevated surface.
- NEVER leave baby unattended.
- NEVER Allow your bouncer to be used as a toy.
- NEVER move bouncer with the child inside.
- NEVER substitute parts.
- Bouncer is NOT intended for use as a carrier.
Check your bouncer for loose screws, worn parts, torn material or stitching on
a regular basis.Replace or repair parts as needed.
Discontinue use of the bouncer should it malfunction or become damaged.
IMPORTANT: Adult assembly required. Care should be taken in unpacking
and assembly. Examine product frequently for damage, missing or loose parts.
DO NOT use if any parts are missing, damaged or broken. Contact Baby Trend for
replacement part and instructions if needed. Dial
800-328-7363
PARTS
Check that you have all the parts for this model before assembling the bouncer.
ASSEMBLY
BOUNCER FRAME ASSEMBLY
-
Place the rear base frame tube on a flat surface (Fig. 1a) and lift the plastic corners (Fig. 1b). Insert the left and right base frame wires into the rear base frame tube.
Push the plastic corners back down until they snap securely onto the base frame wires (Fig. 1c). Set the assembled Base frame aside and proceed to step -
-
• Reference the 3-Way Connector Diagram below for Steps 2 and 3.
• Use de referencia el Diagrama del Conector de 3 Vías a continuación para los pasos 2 y 3.
• The 3-Way Connectors will be preassembled at corner A (Fig 2a). Place the Base frame upright on a flat surface with corners B and C of the 3-Way Connectors pointing up (Fig. 2b). The Backrest Bar has 2 square brackets with an opening for the Toy Bar. Be sure that the openings are facing up (Fig 2b). Align the Backrest bar to corner B. Insert both ends into the 3-Way connector until they click into place (Fig 2c).
DO NOT Discard the Foam Padding from the
Footrest Wire (Fig 2d).
To Insert the Footrest Wire, align the ends to corner C of the 3-Way Connector.Be sure the small curvature parallels with the surface and the ends of the wire both point up (Fig 2d). Insert the ends into the 3-Way Connectors and be sure that they click into place.
NOTE: The pins on the 2 Bars must click into position when inserted into the connectors correctly (Fig. 2e).
-
The completed frame assembly should look exactly as what is shown in (Fig 3).
-
For safety and assurance check that the screw on the 3-Way Connector is tightened on both sides (Fig. 4).
-
Bouncer frame assembly is complete (Fig. 5).
Battery Installation
The music/vibration unit requires two size C batteries (not included). It is
recommended that you use alkaline batteries for longer battery life.
CAUTION: To prevent battery leaks, which can burn skin and eyes:
- Remove batteries when storing product for a long time.
- Dispose of used batteries immediately.
- Always replace the entire set of batteries at one time.
- Never mix old and new batteries, or batteries of different brands or types.
WARNING: Keep batteries out of children’s reach. Old and new batteries should not be mixed. Alkaline, standard carbon-zinc, and rechargeable nickel- cadium batteries should not be mixed. Remove batteries before storing music center for a long period of time.
INSTALLING THE BATTERIES
Remove the battery cover using a Philips screwdriver (Fig. 6). Install two
size C batteries and replace the battery cover.
Do not overtighten the screw.
Align the mounting groove on the unit to the corresponding slot on Footrest
wire.
Slide the unit onto the mounting groove until it is securely in place (Fig.
7).
Unbuckle the straps on the back of the seat pad (Fig. 8).
Slide the top of the seat pad over the backrest tube (Fig. 9).
Pull the front edge of the seat pad over the music/vibration unit and then
pull each side of the seat pad over the footrest wire until it fits snugly
over the bouncer frame (Fig 10a).
Follow the three illustrated steps to cover the Music/Vibration Unit and
Footrest wire (Fig. 10b). The covered bouncer should have the cover wrapped
nicely all around the upper frame assembly (Fig. 10c). 
Secure the seat pad to the frame by buckling the straps on the back of the pad (Fig. 11). Place the bouncer backin the upright position.
TOY BAR INSTALLATION
Position the toy bar above the bouncer as shown (Fig. 12a). Insert the ends of
the toy bar through the corresponding holes in the seat pad and into
corresponding holes on the frame. Push in until both sides click into place.
To remove, press the release clips and pull up (Fig. 12b).
To hook the Headrest to the Bouncer, use the
adjustable hook and loop strap. Thread it from front to back through the
headrest hoop. To adjust detach and attach the hook and place it at your
desired height (Fig. 13).
If buckled, unbuckle the straps on each side of the seat restraint (Fig. 14a).
Carefully place the child in the bouncer seat and buckle the straps (Fig.
14b). Adjust the straps so that the restraint fits the child snugly (Fig.
14c).
CARE AND CLEANING
Remove the seat pad and headrest from the frame. Ensure that all buckles on the seat pad are fastened. Do not iron. Do not dry clean.
Instructions:
WASHING INSTRUCTIONS (Seat Pad /Head Rest): Machine wash on gentle delicate
cycle with cold water. Do not bleach. Do not tumble dry. Hang to dry. Do not
iron. Do not dry clean.
TOY BAR AND TOYS: Wipe clean with a damp cloth and mild soap. Air dry. Do not
immerse in water.
FRAME: Wipe the metal frame with soft, clean cloth and mild soap.
OTHER OTRO
MUSIC/VIBRATION UNIT
To use the vibration function: To activate the vibration function, slide the vibration switch to the ON position.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try tocorrect the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Copyright © 2023, Baby Trend Inc., All Rights Reserved. Todos los derechos reservados.
References
- Limited Warranty Coverage – Baby Trend
- Baby Trend® | Car Seats, Strollers, High Chairs, Nursery and More!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>