CRUX ONST-11C Wiring Interface Instruction Manual

June 12, 2024
CRUX

CRUX ONST-11C Wiring Interface

CRUX ONST-11C Wiring Interface

PRODUCT FEATURES

  • Retains factory features in select GM LAN 11 Bit vehicles while functioning with an aftermarket radio.
  • Pre-programmed to retain factory Steering Wheel Controls.
  • Supports Non-Bose and Bose amplified systems.
  • Provides Vehicle Speed Sensor (VSS), Parking Brake and Reverse Outputs.
  • Retains factory OnStar®
  • Retains chime functions
  • EIA color coded wiring for easy installation.

PARTS INCLUDED

  • CS-GM11C MODULE

  • CS-GM11C HARNESS

  • SWC CABLES

INSTALLATION DIAGRAM

Installation Diagram

DIP SWITCH SETTINGS

AFTERMARKET RADIO DIP SWITCH SETTINGS:

RADIO BRAND: DIP#: 1 2 3 4
Atoto, Dual, Fahrenheit, Jensen, OFF OFF ON ON
Pioneer, Power Acoustik, Sound stream OFF OFF ON ON
Blaupunkt, most off-brand Radio OFF OFF ON ON
Alpine OFF OFF OFF OFF
Clarion OFF ON ON OFF
kenwood OFF ON ON ON
JVC OFF ON ON ON
Boss, Old Sony OFF ON OFF OFF
New Sony OFF OFF ON OFF

SWC MODULE DIP SWITCH

NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Sound stream, and most off-brand radios, check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.

4-PIN SWC CABLE

Use the proper 3.SMM to 4-Pin SWC cable for the aftermarket radio you are using.

OPTION A is used for ALPINE, CLARION, JVC, arnd KENWOOD units (Blue/Yellow wire is attached)
OPTION Bis used for BLAU PUN KT, BOSS, DUAL, FAREN HEIT, JENSEN, POWER ACOUSTIK,  PIONEER,SONY, SOUNDSTREAM and Most Off-Brand Radios.

NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.

Plug the SWC cable to the ONST-11C module and the 3.5mm plug to the aftermarket radio SWC port or use the Blue/Yellow wire for JVC and Kenwood radios.

SELECTING THE AUDIO SYSTEM

If the vehicle is equipped with an amplified audio system, the ONST-11 C has a built-in audio level adaptor that outputs the proper audio level from the aftermarket radio to the factory amplifier. To use this feature, plug in the male 8-pin connector on the ONST-11C harness to the GRAY female 8-pin connector on the ONST-11 C module. The module is also labeled “Bose” and “Non Bose” to avoid confusion. (see picture below)

If the vehicle is NOT equipped with a factory amplified system, plug in the male 8-pin connector to the BLACK female 8-pin on the ONST-11C module.

CHIME VOLUME ADJUSTMENT

The CS-GM11C has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust the volume, simply use a suitable screw driver and turn the potentiometer clockwise to increase the volume and counter-clockwise to decrease the volume.

VEHICLE APPLICATIONS

CHEVROLET
2005-2006 Cobalt
2004-2007 Malibu

PONTIAC
2005-2009 G6*

*NOTE: If the 2009 G6 radio has one volume knob in the center of the radio, please use part# ONST-11B instead.

Compatible Radio

Compatible Radio

DIP switch settings for Pioneer receivers:

DIP switch settings for Pioneer receivers:

Location of the switch may vary on the Interface (Comer or Middle).
Please note that interfaces with DIP at the end of the LOT# are installed with the switch.

  • Set DIP switch to “3V3” position for  support of NEW generation Pioneer steering wheel button control.
  • Set DIP switch to “5V” position for support of OLD generation Pioneer steering wheel button control.

Crux Interfacing Solutions • Chatsworth, CA 91311
phone: 818-609-9299 • fax: 818-996-8188www.cruxinterfacing.com

CRUX Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals