SENA 50S Bluetooth Motorcycle Communication System User Guide

SENA 50S Bluetooth Motorcycle Communication System

Charging

• Red LED: Charging
• Blue LED: Fully charged

Power On/Off

• Press and hold the Jog Dial and Phone Button for 1 second
• Tap the Jog Dial and Phone Button.

Volume Adjustment

Increase/Decrease the volume : Rotate the Jog Dial clockwise or counterclockwise

Battery Check

Phone, Music Pairing

1. Press and hold the phone Button for 5 seconds.
2. Search for Bluetooth devices on your mobile phone. Select the Sena 50S in the list of the devices detected on the mobile phone.
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.

Music Operation

Play or pause music: Press and hold the Jog Dial for 1 second. Track forward/ back: Rotate while pressing the Jog Dial clockwise or counterclockwise.

Mobile Phone Call Making and Answering

• Answering a call: Tap the Phone Button
• Ending a call: Tap the Phone Button
• Voice dial: Tap the Phone Button
• Speed dial: Double tap the Phone Button
• Rejecting a call: Press and hold the Jog Dial for 2 seconds.

Intercom

Intercom Pairing

1. Press and hold the Jog Dial of two headsets for 5 seconds until red LEDs of both units start to flash rapidly.
2. Simply tap the Jog Dial of any one of the two headsets.

Intercom Start/End: Tap the Jog Dial.

Radio On/Off

• Turn on the FM radio: Press the Phone Button for 1 second.
• Turn off the FM radio: Press the Phone Button for 1 second.

Radio Scan Up FM Band

• Start scanning: Double tap the Phone Button
• Stop scanning: Double tap the Phone Button

Save presets while scanning: Save presets: Tap the Phone Button

Radio Move to Preset Station

Move to next preset: Press the Jog Dial for 1 second (1 → 2 → … → 10)

Radio Seek Stations

Seek up/down stations: Rotate while pressing the Jog Dial clockwise or counterclockwise.

Setting

Configuration Menu: Press the Jog Dial for 10 seconds.

Using the Sena Device Manager
Connect the headset to your computer via a USB cable. Launch the Sena Device Manager and click DEVICE SETTING to configure the headset settings. For details about downloading the Sena Device Manager, please refer to the leaflet included in the package.

Troubleshooting

Factory Reset

If you want to restore the headset to factory default settings, use the Factory Reset in the configuration menu. The headset automatically restores the default settings and turns off.

Certification and Safety Approvals FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antennae
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. When equipped, the distance between antenna and one’s head surface is 40mm.

FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>