E-COLLAR FE-560 FOB Educator User Manual

E-COLLAR FE-560 FOB Educator User Manual

DEVICE OPERATION

1. L-Button : Selecting Lighting mode operation
2. R-Button : Selecting the operation time of Rising Stimulation Mode
3. Micro-B USB Charger port : Transmitter Charging Port (Micro-B type USB)
4. LED Indicator : Indicate signal transmission status and Battery status.
5. S(Black)-Button : Stimulation operation with set stimulation level
6. S(Red)-Button : Operation with pre set mode among Stimulation / Tone / Vibration / Rising Stimulation mode
7. LCD Display : Indicates Transmitter transmission level, operation status, and Dog1/Dog2 status
8. (+)-Button : Stimulation Level Up
9. (-)-Button : Stimulation Level Down
10. Power-Button : Transmitter Power ON/OFF
11. Program-Button : Enter programming mode & Dog select in 2Dog mode

CHARGING THE BATTERIES

Indicator Light is blinking “Green” under normal operation. solid “Red” when stimulation is applied. blinking “Red” when recharging is required.
Do not allow the batteries to get hot or be fully discharged, store at room temperature and 50% capacity charge.

The indicator light will turn solid red during charge cycles and turn green if it is fully charged. (approximately 2 hours)

Please add this about the batteries : Your e-collar is outfitted with Li- Polymer batteries which requires specific care to assure longevity. It is best not to let the battery be fully discharged and if it does, recharge immediately or irreversible damage may occur. Keep the units away from extreme heat and cold temperatures.

POWER ON/OFF

Transmitter can be turned on and off by pressing the Power-Button.

THE LCD DISPLAY DESCRIPTION

[All LCD Display]

• LCD Display

FUNCTION DESCRIPTION

• Function Description
  – Stimulation While the button is pressed, the stimulation with currently set stimulation level is transmitted. (Maximum operating time : 10 seconds)
  – Rising Stimulation While the button is being pressed, it transmits an operation signal whose level increases from the currently set stimulation level to the stimulation max level for a defined time interval. (Stimulation Max Level and time interval can be set separately.)
  – Vibration While the button is pressed, it transmits a vibration operation signal Two vibration modes (LOW(weak vibration) / HI(strong vibration)) available.
  – Tone or Tone followed by Stimulation (Pavlovian Conditioning) While the button is pressed, the tone operation signal is transmitted for 1.25 seconds. If the button is pressed after 1.25 seconds, the stimulation signal with the current stimulation level is transmitted. (Maximum operating time 10 seconds)
  – When Transmitter Stimulation Level is “0”, only Tone operation signal is transmitted.
  – Lighting When the button is pressed, a Lighting operation signal is transmitted. (RX toggles “Ficker -> Solid -> OFF -> Flicker …” in turns whenever it receives a signal.)

BUTTON OPERATION – 1DOG MODE

• 1Dog Mode

BUTTON OPERATION – 2DOG MODE

• 2Dog Mode

PROGRAMMING MODE

– Press Program-Button at Level 0 for more than 2 seconds and release the button to enter Programming mode-1 (P1).
– If keep pressing the button for 1 second more without releasing button, can enter Programming mode-2 (P2). (When enter the programming mode, the LCD display shows “P1 -> P2” in order and release the Program-button to set the mode.)
– While Program-Button is pressed, it cycles every second by “P1-> P2-> P1…”. When you release the button, it enters the mode displayed on the LCD.

< 1Dog Mode >

– In Programming mode, the function of S(Red)-Button for Dog1 can selected by pressing S(Red)-Button.
– Pressing the Program-Button saves the current settings and exits from Programming mode.

• Setting stimulation level Increasing step

– Stimulation level is increased by each pressing (+)-Button as much as level increasing step which can be set by one of 1, 5 and 10 steps. (Default setting is 5 steps.)
– Setting Procedure

1. Enter P1 mode.
2. Press S(Red)-Button to select Stimulation Mode which has icon.
3. Press Level Up Button ((+)-Button) to set the desired step.
4. Press the Program-Button to save and exit the programming mode.

< 2Dog Mode >
– In Program mode, the function of S(Black)-Button for Dog1 can be selected by pressing S(Black)-Button and the function of S(Red)-Button for Dog2 can be selected by pressing S(Red)-Button.
– Pressing the Program-Button saves the current settings and exits from Programming mode.

• Setting stimulation level Increasing step

– Stimulation level is increased by each pressing (+)-Button as much as level increasing step which can be set by one of 1, 5 and 10 steps. (Default setting is 5 steps.)
– Setting Procedure

1. Enters P1 mode.
2. Press S(Black)-Button to select Stimulation Mode for Dog1 which shows on the LCD, and press S(Red)-Button to select Stimulation Mode for Dog2 which shows on the LCD.
3. Press Level Up Button ((+)-Button) to set the desired step.
4. Press the Program-Button to save and exit the programming mode.

RISING STIMULATION

It is possible to increase the voltage from the current stimulus level to the set maximum stimulus level in preparation for the cognitive stimulus intensity setting or emergency of the dog.

< 1Dog Mode>

• Rising Stimulation Operation
  – Press the Rising Stimulation button to increase the stimulus output from the current stimulus level up to the maximum stimulus level.
  – The time to reach the maximum stimulus level can be set by pressing the R-Button.

• Rising Stimulation Operation Button
  – Press Stimulation (Black) -Button and Program-Button with the current stimulus level not “0”.
  – In programming mode, set Stimulation (Red) -Button to, then press Stimulation (Red) -Button.

• Set stimulus level rise time : Time to reach the maximum stimulus level set from the current stimulus level can be set.
  – Every time you press R-Button in standby, “r0-> r1-> r2-> r5 …” is changed in turn.
  – When you exit the mode from the currently selected screen, the last selected time is automatically set.

< 2Dog Mode>

• Rising Stimulation Operation
  – Press the Rising Stimulation button to increase the stimulus output from the current stimulus level up to the maximum stimulus level.
  – The time to reach the maximum stimulus level can be set by pressing the R-Button.

• Rising Stimulation Operation Button
  – Dog1 Operation Button
  – Press Stimulation (Black) -Button and Program-Button with the current stimulus level not “0”.
  – In programming mode, set Stimulation (Black) -Button to, then press Stimulation (Black) -Button.
  – Dog2 Operation Button
  – Press Stimulation (Red) -Button and Program-Button with the current stimulus level not “0”.
  – In programming mode, set Stimulation (Red) -Button to, then press Stimulation (Red) -Button.

• Set stimulus level rise time : Time to reach the maximum stimulus level set from the current stimulus level can be set.
  – Every time you press R-Button in standby, “r0-> r1-> r2-> r5 …” is changed in turn.
  – When you exit the mode from the currently selected screen, the last selected time is automatically set.

Dog1 Setting : In standby mode, press Program-Button to display 1D and press R-Button to set time.

Dog2 Setting : In standby mode, press Program-Button to display 2D and press R-Button to set time.

STIMULATION LEVEL BUTTON LOCK/UNLOCK

The stimulation level set by the user can be fixed

• Stimulation Level Button Lock
  – Press (-)-Button while pressing Program-Button to set Stimulation Level Button Lock function.
  – When the Stimulation Level Button Lock function is activated, pressing the

• Stimulation Level Up / Down Button generates a buzzer sound and the Stimulation Level can not be adjusted. Stimulation Level Button Unlock
  – If press (-)-Button while pressing Program-Button when Level button Lock function is set, the Stimulation Level Button Lock function is released.

– Stimulation Level Up/Down Button Lock/Unlock setting is independent to the ALL Button Lock/Unlock setting. For example, if the ALL Button Lock function is released, the Stimulation Level Up / Down Button Lock setting will not be released.

PAIRING

1. Power on Transmitter.
2. Change Transmitter Stimulation Level to “0” using (-)-Button.
3. Power off Receiver
4. Press and hold the Power-button on the Receiver and release the button when the Receiver LED indicator flashes green.
5. Hold down (-)-Button on the Transmitter and press L-Button.
6. Pairing is completed with buzzer sound of Receiver.

* Pairing when 2Dog Mode

FCC Statements

Model: FE-560 TX
FCC ID: 2ASPX-FE-560TX

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

< Receiver >

1. 5/8″ Contact Point
2. Battery Charging Receptacle and Rubber Cover
3. Power-Button : Receiver Power ON/OFF
4. LED Indicator & Light Window : Battery indicator & Light
5. Collar Strap

Collar Receiver Battery Charging Receptacle and Rubber Cover.

Collar Receiver can be turned on and off by pressing the Power-Button. Power- Button

– Power ON : When the receiver is off, press the Power-Button for more than 1 second to turn it on.
– Power OFF : When the receiver is on, press the Power-Button for more than 1 second to turn it off.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>