SERVER 06992 Express Pump Instruction Manual

June 5, 2024
SERVER

06992 Express Pump

Server Express® Pump
07968 PUMP used with pouches up to 3 gallons with 38mm threaded connector.
h 06992 PUMP includes additional connector for 1½ gallon pouches with 16mm piercing fitment.
Thank You
for purchasing our Server Express® Pump. Express® pouched condiment systems are sealed and sanitary, achieve excellent evacuation and have only a few parts for easy clean-up. SIMPLIFY CONDIMENT MANAGEMENT–GO POUCHED

ASSEMBLY

WASH ALL PARTS PROPERLY BEFORE USE. See page 3.

1 INSERT PINCH VALVE
into pump housing.
TIP: Squeeze the pinch valve open before installation to ensure it isn’t stuck shut.

2 INSTALL DOME
Press dome into housing fully.
Ensure valve flap covers bottom opening.

Wrap loop around lower opening to secure dome.

3 INSTALL TUBE
Lubricate with a small amount of clean water. Rotate and position until both pegs on housing fit into holes on tube.

4 INSERT CONNECTOR
FOR 1½ GALLON POUCH: USE 16MM CONNECTOR
FOR 3 GALLON POUCH: USE 38MM CONNECTOR
Lubricate connector with a small amount of clean water. Rotate and position until both pegs on connector fit into holes on tube. Connector end must point away from discharge tube.
5 INSERT DISCHARGE FITTING
into pump housing discharge tube. Place loop of fitting around peg on end of discharge tube to secure.

Page 2

SAFETY

DISASSEMBLY

IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly to comply with local sanitization requirements.
According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Server Products, Inc. cannot be responsible for the serving of potentially hazardous product.
NSF International lists this pump as: “Not acceptable for dispensing potentially hazardous foods.”

CLEANING

1 FLUSH & RINSE all pump surfaces with hot water. Place lower end of pump into container of hot water and operate pump until all remaining product is expelled and only hot water is discharged.
2 DISASSEMBLE & CLEAN all washable parts with soap and hot water. Use brush to clean any confined areas.
3 RINSE fully with clear water.
4 SANITIZE all parts according to local sanitization requirements. All parts in contact with food must be sanitized.
5 AIR DRY all parts fully.

YES!
Use dishwashing soap, hot water and nylon brush
· Dishwasher safe · Do not use abrasive, caustic or ammonia
based cleansers. · Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine. · Do not use metal scrapers or cleaning
pads that could scratch surfaces.

TROUBLESHOOTING

TIP: Squeeze the pinch valve open before installation to ensure it isn’t stuck shut.

DIFFICULT TO ATTACH PARTS?
· Wet parts with clean water to help fit.
PRODUCT DOESN’T PUMP?
· Ensure pinch valve is inserted in housing. · Ensure connector is snapped fully in place to
fitment in pouch. · Ensure pump is properly installed in unit. · Clean pump thoroughly.
DOME POPS OFF?
· Clean thoroughly. Food residue could prevent a tight seal between dome and housing.
· Ensure dome edges are flush with housing. Page 3

PUMP COMPONENT PART NUMBERS

DOME

PINCH VALVE 07798
PUMP HOUSING 07388

PART
DOME TUBE CONNECTOR(S)

PUMP 07968
07399 07404 07588

PUMP 06992
07383 06993 07588 & 07381

DISCHARGE FITTING 07796
TUBE
CONNECTOR 07588

CONNECTOR 07588 PIECES
Black gasket into groove.

Threads in ring face pointed end.

CONNECTOR 07381
SERVER PRODUCTS LIMITED WARRANTY
This Server product is backed by a two-year limited warranty against defects in materials and workmanship. See Server-Products.com for details.
NEED HELP?
Server Products Inc.
3601 Pleasant Hill Road Richfield, WI 53076 USA
Chat with us!
spsales@server-products.com 262.628.5600 | 800.558.8722

Pump 06992 includes connector 07381, for use with 1½ gallon pouches with 16mm fitments.
GENERAL SERVICE, REPAIR OR RETURNS
Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge.

Please be prepared with your Model, P/N and Series located on the lid or base of the unit.

Example:

MODEL XXXX P/N SERIES ##X ##X

Page 4

Manual #EM_01765_RevC 060722

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals