Nedis RDFM1320SI FM Radio User Manual

: June 5, 2024
: nedis

RDFM1320SI FM Radio

Nedis RDFM1320SI FM Radio

User Manual

Preface

Thank you for purchasing the Nedis RDFM1320SI.

This document is the user manual and contains all the information for correct, efficient and safe use of the product.

This user manual is addressed to the end user. Read this information carefully before installing or using the product.

Always store this information with the product for use in the future.

Product description

Intended use

The RDFM1320SI is a portable AM/FM radio that can be used on-the-go with batteries or can be connected to a power outlet.

The product is not intended for professional use.

Any modification of the product may have consequences for safety, warranty and proper functioning.

Specifications

Product

|

FM Radio

---|---

Article number

|

RDFM1320SI

Dimensions (l x w x h)

|

72 x 230 x 160 mm

Radio bands

|

FM

FM frequency range

|

88.0 – 108.0 MHz

FM tuning

|

Analogue

Power

|

0.5 W

Peak power

|

1.5 W

Connections

|

3.5 mm headphones output

Power input

|

220 – 240 VAC ; 50 Hz

Battery type

|

4 x 1.5 V AA (not included)

Main parts (image A)

A

1. Carrying handle

2. Speaker

3. Tuning wheel

4. Volume wheel

5. Frequency indicator

6. Function switch

7. 3.5 mm headphones output

8. Antenna

9. Power port

10. Battery compartment

11. Power cable

Safety instructions

WARNING

|

To prevent possible hearing damage, do not listen at high volume levels for long periods.

---|---

Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep this document for future reference.
Only use the product as described in this manual.
Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
Do not drop the product and avoid bumping.
This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
Disconnect the product from the power source and other equipment if problems occur.
Do not expose the product to water or moisture.
Do not recharge non-rechargeable batteries.
Do not dismantle, open or shred secondary cells or batteries.
Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.
Do not short-circuit a cell or a battery.
Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects.
Do not remove a cell or battery from its original packaging until required for use.
Do not subject cells or batteries to mechanical shock.
In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
Observe the plus (+) and minus (–) marks on the cell, battery and equipment and ensure correct use.
Do not use any cell or battery that is not designed for use with the product.
Seek medical advice immediately if a cell or a battery has been swallowed.
Keep cells and batteries clean and dry.
Wipe the cell or battery terminals with a clean dry cloth if they become dirty.
Use only the cell or battery in the application for which it was intended.
Battery usage by children should be supervised.
Do not mix cells of different manufacture, capacity, size or type within a product.
Properly dispose of the empty battery.
When possible, remove the battery from the product when not in use.
Some wireless products may interfere with implantable medical devices and other medical equipment, such as pacemakers, cochlear implants and hearing aids. Consult the manufacturer of your medical equipment for more information.
Do not use the product at locations where the use of wireless devices is prohibited due to potential interference with other electronic devices, which may cause safety hazards.

Safety symbols on the product

Icon

|

Description

---|---

|

Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.

|

Product in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions such as double insulation or reinforced insulation are provided, there being no provision for protective earthing or reliance upon installation conditions NOTE A Class II products may be provided with means for maintaining the continuity of protective circuits, provided that such means are within the product and are insulated from accessible surfaces according to the requirements of Class II.

|

Indication to explain that the product can cause hearing damage. Do not listen at high volume levels for long periods.

|

Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.

Installation

Check the contents of the package
Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.

Inserting the batteries

1. Open the battery compartment A q.

2. Insert 4 type AA batteries.

Make sure to match the (+) and (-) polarity markings.

3. Close A q.

Connecting the product to a power outlet

1. Plug the power cable A w into the power port A 9.

2. Plug the other end of A w into a power outlet.

Use

Switching on the product

1. Set the function switch A 6 to AM or FM.

Controlling the volume

1. Rotate the volume wheel A 4 to adjust the volume to the desired sound level.

Tuning in to a radio station

1. Rotate the tuning wheel A 3 to select an available radio station.

The frequency indicator A 5 shows the current frequency value.

Maintenance

Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.

Warranty

Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.

Disclaimer

Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.

Disposal

|

This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.

---|---

Declaration of Conformity

We, Nedis B.V. declare as manufacturer that the product RDFM1320SI from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.

The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via:

nedis.com/rdfm1320si#support

For additional information regarding the compliance, contact the customer service:

Web: www.nedis.com

E-mail: service@nedis.com

Phone: +31 (0)73-5991055 (during office hours)

Nedis B.V., de Tweeling 28

5215 MC ’s-Hertogenbosch, the Netherlands