Nedis VREP3401AT HDMI Extender User Manual
- June 5, 2024
- nedis
Table of Contents
VREP3401AT HDMI Extender
User Manual
Preface
Thank you for purchasing the Nedis VREP3401AT .
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
The Nedis VREP3401AT is a HDMI extender for connecting two HDMI cables and cleaning out the digital noise.
The HDMI extender allows the signal to extend to a maximum of 15 meters, using 24AWG cables, or 25 using 20AWG cables.
The extender supports a video resolution of 4K at 60 Hz.
Intended use
The product is exclusively intended as an extender for HDMI signals.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
HDMI extender
---|---
Article number
|
VREP3401AT
Dimensions (l x w x h)
|
48 x 22 x 13 mm
Weight
|
19 g
Operating temperature
|
0 °C – 45 °C
Storage temperature
|
-10 °C – 80 °C
HDMI input/output connector
|
Type A 19 pin female
Maximum single link range
|
3840 x 2160 at 60 Hz
Vertical frequency range
|
50 / 60 Hz
Video amplifier bandwidth
|
6 Gbps / 600 MHz
Interlaced (50 and 60 Hz)
|
480i, 576i, 1080i
Progressive (50 and 60 Hz)
|
480p, 576p, 720p, 1080p, 4K
Parts list
1. HDMI input
2. HDMI output
Safety instructions
WARNING
- Only use the product as described in this manual.
- Do not use a damaged product.
- Keep the product out of reach from children.
- Do not expose the product to water or moisture.
Installation
- Check the contents of the package
- Check the product for any visible damage. If the product is missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Connect the HDMI extender to the source device
1. Plug an HDMI cable into the HDMI Out port of the source device.
2. Plug the other side of the HDMI cable into the HDMI In port 1 of the extender.
Connect the HDMI extender to the HDMI output
1. Plug a second HDMI cable into the HDMI In of the receiver.
2. Plug the other side of the HDMI cable into the HDMI Out port 2 of the extender.
- The receiver can be any device with a display and HDMI In port.
Use
- Switch on the source.
- The input source will now be streamed to the receiver.
Maintenance
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>