Shenzhen Yunmai Technology P701 Yunmai Smart Rope Instruction Manual

Shenzhen Yunmai Technology P701 Yunmai Smart Rope

Product introduction

Thank you for choosing YUN MAI Sm.lrt Rope.

How to assemble

1. Remove the Smart Rope handle cap from the handle body.
2. Pass the rope into the buckle and hole in the follow direction.
3. Adjust the length and then through the buckle, tighten the rope.
4. Fasten the length of the rope with buckle and cover the body cap of the skipping rope handle.

Ready for use

Install YUNfo’IAI App

Scan the QR code below to download and install YUN MAI App.
The App is also available in Google Play and App Store.
App downloaded from other channels may be unusable. Before pairing with your device, please confirm that your device meets the following requirements:

1. iPhone I iPod touch devices running ios 10.0 and above:
2. Mobile phone equipment running Android 4.3 and above and equipped with Bluetooth 4.0.

Bluetooth connection

1. Turn on the Bluetooth of the mobile phone and keep the rope handle in the state of power-on.
2. Open” YUNMAI App • and click’ Me”; Enter” Smart Equipment’ and select” YUNMAI Smart Rope”;
3. Pull down to enter the Bluetooth matching mode when you success to get into the homepage. The white indic.ator light in the displ.ay area of the handle flashes,which means that the pairing in progress, and the white light is long bright,which means that the device has been connected.

Note: Bee.a use the iteration speed of the YUN MAI App is fast, the features listed on this page are subjected on the actual market products, please forgive to have not another notice If there Is some change.

How to starting up

1. Hold” On/Off” button for 2 seconds, ” 88B8 “will be displayed in the screen, and then the system Is sta11ed successfully.
2. Hold” On/Off’ button for 4 seconds,’ ffF” will be displayed in the screen, and then system Is switched off successfully.
3.  Pressing” On/Off’ button shortly could switch to current number of skipping or Last time, and cumulative total number of exercises.
4.  Press’ On/Off” button twice, it will displ.ay the reset. You can start skipping.

Charging mode

Select the handle with • On-Off• button, open the charging cover which loc.atedat the bottom of the handle, insert the Micro-use charging line Into the charging port. Then It starts charging when the power Is supposed .

Kindly remind

1.  Please wear shock-absorbing sports shoes when skipping rope, in order to better protect your ankles and soles ofyour feet.
2.  Warm-up exercises before skipping rope is neCf!;sary to help accelerate the blood circul.ation of the body, making tendons more flexible, and avoiding the damage to joint, ligament and muscle.
3.  Please do stretching exercises after the skipping rope, especially stretching the legs, which could relieve muscle tension or soreness.
4.  Venues with moderate hardness, such as Lawns, pl.astic sports fields, gymnasiums is suggested area for sport. A rough ground will increase the resistance of the rope and accelerate the rope wear.
5.  Please try to choose an empty place to avoid hurting others.

Warranty

YUN MAI provides one-year limited warranty.

FCC warning

Any Changes or modifications not expressly approved by the pa11y responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found ta comply with the limits for a Class B digital device, pursuant to pa1115 of the FCC Rules.
These limits are designed ta provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used In accordance with the Instructions, may cause harmful Interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followlng measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1.  This device may not cause harmful interference
2.  This device must accept any interference received, including interference that may cause undesired operation.

Product Specifications

Product name: YUNMAI Smart Rope
Product model: YMSR-P701
Bady size: 161.7 x 2S.6 x 25.6mm
Main materials: PC, PU
Packing list: skipping rope handle x2, 3m Long rope xl, storage bax x7,
instruction manual xl, Micro-USB charging line xl Manufacturing address: Shenzhen, Guangdong
Manufacturer: Shenzhen YUNMAI Technology Co., Ltd
Address: Room#19A, Chiwan Headquarters Building, N0.8 Chiwan 6th Road, Nanshan District, Shenzhen, China

Please visit https://www.lyunmal.com far more details.
Email: support@iyunmai.com
lnst.agram: @yunmaiglobal
Facebook: @Yunmaipr
Manufacturer: Shenzhen Yunmai Technology Co., Ltd.
Company Address: Room#7 9A, Chiwan Headquarters Building, NO.a Chiwan 6th Road, Nanshan District, Shenzhen, China
09

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>