levoit LUH-D302 Dual 150 Ultrasonic Cool Mist Humidifier User Manual

levoit LUH-D302 Dual 150 Ultrasonic Cool Mist Humidifier

SAFETY INFORMATION

To reduce the risk of fire, electric shock, or other injury, follow all instructions and safety guidelines.

• General Safety Only use the humidifier as described in this manual. Place the humidifier and cord so that it will not be knocked over. Do not place near large pieces of furniture or in high-traffic areas.
• When not in use, turn the humidifier off and disconnect from power by removing the plug from the outlet.
• Do not use the humidifier in wet environments.
• Keep the humidifier out of reach from children.
• Do not open the base or remove the water level sensor for selfservicing.
• • Always unplug your humidifier from the power outlet before cleaning your humidifier or detaching the water tank from the humidifier base.
• Always make sure to place the humidifier on a flat, level surface before operation.
• Only fill the water tank with clean water. Never fill the water tank with any other liquids.
• Do not place the humidifier near sources of heat, such as stovetops, ovens, or radiators.
• Do not place the humidifier directly on floors, carpets, or rugs.
• Do not use other items as replacement parts for this product.
• Do not cover the nozzle while the humidifier is on. Doing so may damage the humidifier.
• Remove the water tank from thebase before moving the humidifier.
• Do not immerse the humidifier base, power cord, or plug in wat er.
• If the humidifier is damaged or is not functioning properly, stop using it and contact Customer Support immediately (see page 10).
• This humidifier is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Supervise children when they are near the humidifier.
• Children should not clean or perform maintenance on the humidifier without supervision. Children should be supervised to ensure that they do not play with the humidifier.
• Household use only. Not for commercial use.

Caution: Risk of Leaks and Electric Shock

• Do not add supplemental water treatment liquids into the water tank or base chamber.
• This will damage the humidifier and cause leaks.

Power & Cord

• Ensure that the plug fits properly into a polarized socket.
• Do not handle the power cord or plug with wet hands. Keep the plug and power cord away from liquids.
• Your humidifier has a polarized plug (one prong is wider than the other), which fits into a polarized outlet only one way. This is a safety feature to reduce the risk of electric shock. If the plug does not fit, reverse the plug. If It still does not flt, do not use the plug in that outlet. Do not bypass this safety feature.
• If the power supply cord is damaged. it must be replaced by Arovast Corporation or similarly qualified persons in order to avoid an electric or fire hazard. Please contact Customer Support (page 10).

Package Contents

• 1 x Ultrasonic Cool Mist Humidifier
• 2 IC Water Filter Sponges (1 Pre-Installed)
• 1 1C Cleaning Brush
• 1 IC User Manual

Specifications

0.79 gal/ 3 L

Max Ru n Time

| Up to 25 hours on rninirnurn rnist setting

Nate: The humidifier may run for o l o nger or shorter time de p e nd i nq on the e nv i r onm e nt al temperature ond humidity

Noise Level| < 28dB
Effective Ran ge| ****

107-290 ft’/10-27 rn’

Dimensions

| 7.2 X 8.1 X 11_6 in/

18.3 x 20.6 x 29.4 cm

We i g ht| 3 lb I1.38 kg

GETTING TO KNOW YOUR HUMIDIFIER

• A. Nozzle
• B. Water Tank Cover
• C. Water Filter Housing
• D. Water Filters. Transducer
• E. Mist Tube
• F. Water Tank
• G. Float
• H. Refill Indicator Light
• I. Control Kn ob
• J. Base
• K. Cleaning Brush
• L. Power Cord
• M. Max Water Line (Tank)
• N. Water Outlet Valve
• 0. Noise Silencer
• P. Air Outlet
• Q. Max Water Line (Base)
• R. FI oat Brackets
• s. Transducer
• T, Secondary Float
• u. Feet
• v. Air Inlet

CONTROLS

Control Knob

• Rotate clockwise to turn on the humidifier and to adjust the mist level.
• Rotate counterclockwise to turn off the humidifier.
  Note: There is a clicking sound when the humidifier turns on/off.

Refill Indicator Light

• The red light turns on when the water tank Is empty. Refill the water tank (see page 5).
• The red light turns off when the water tank is fil led.

GETTING STARTED

1. Remove all packaging.
2. Take the water tank off of the base and remove all 1ape. {Figure 1.1]
3. Rinse and reassemble all parts before first use (see Cleaning, page 6).
   • Note: Check to make sure that the water filter Is correctly In place. If n ot. then rotate the filter c lockwise to secure ff. in place. [Figure 1.2]
   • Check to make sure that the float is securely in place. [Figure 1.3]
4. Choose a hard, flat location for the humidifier at leiist 12 inches/ 30 cm away from any walls. The surface must be water-resistant. [Figure 1.4]
5. Mist should be directed away from walls, furniture, bedding, and appliances. [Figure 1.5]

Filling & Refilling

Note: Make sure the water tank is clean before filling.

1. Tum the humidifier off.
2. Remove the water tank cover by holding the nozzle and pulling upward. [Figure 1.6]
3. FIii the tanK with room-temperature water. [Figure 1.7]
   • Note: We recommend using p urified or dislilled water to fill the tank.
   • Do not fill post the tonk’s mox water hne.
   • Do not fill with not wate(
   • CAUTION
   • Do not add water directly Into the base chamber. [Figure 1.8]
   • Do not add water through the mist tube. [Figure 1.9]
4. Replace the water tank cover. Note: Make sure the nozzle on the woter tonk cover is placed over the mist tube, or the humidifier may not work correctly. [Figure 1.10
5. Optionally, add 10-15 drops of essential oil into the water tank for aromatherapy. [Figure f.11] Nate: For best results. we recommend using pure essential oil

USING YOUR HUMIDIFIER

1. Plug In the humidifier. Rotate the Control Knob clockwise to turn the humidifier on. Adjust the knob to your desired mist level. {Figure 2.1]
2. Rotate the nozzle to adjust the direction of the mist. {Figure 2.2]
3. When your room has reached your preferred humidity level, turn the humidifier to a lower setting, or turn It olf.
4. Rotate the Control Knab counterclockwise to turn the humidifier off.
   Note: If there is no wuter in the tonk or the tonk is removed, the humidifier will stop misting ond the Refill Indicator light will turn on. Refill the tank and properly place it on the base to use your humidifier.

Important Tips
Your humidifier must have the correct level of water in the base chamber to work properly. If there is too much water in the base chamber. the humidifier cannot create mist.

• Never pour water directly Into the base chamber. {Figure 2.3]
• Only add water ta the water tank. The humidifier will autamatlcally release the correct amount of water Into the base chamber.
• Avoid moving or shaking the humidifier. [Figure 2.4]This may cause the water tank to release too much water into tile base chamber.
• Before moving the humidifier, turn it off. unplug it, and remove the water tank
• If your humidifier doesn’t produce mist correctly, check the max water line to see if there is too much water in the base chamber
  • Pour out extra water if water is over the max line. {Figure 2.51
    Note: The max water line Is only tor this purpose. Do not pour water Into the base chamber.

CARE & MAINTENANCE

Nor

• All maintenance should be done on a wuterresistont surface, such as a kitchen counter.
• Change the water doily to ovoid bacteria growth.
• Use a tissue or cloth to clean the nozzle regularly.
• If not using the humidifier for 3 days or longer, do nat leave water inside. Clean and dry the humidifier instead

Cleaning
You should clean your humidifier every 3 days, and when you’re ready to store It

Note:

• Never immerse the base in water or liquid.
• Donat place any part of the humidifier in a dishwasher.
• Do not use detergents to clean the humidlner.

1. Unplug the humidifier.
2. Remove and rinse the water tank cover. {Figure 3.1]
3. Remove the water tank from the base and pour out any water from the tank and base chamber. {Figure 3.2] Note: When pouring out water, hold down the float to ensure that it does not fall out of the base chamber.
4. Remove the water filter assembly from the tank by rotating It counterclockwise and lifting it out. {Figure 3.3)
5. Rinse the tank, water filter assembly, and base chamber with room temperature water. {Figure 3.41

Descallng Your Humidifier

1. Remove the water filter from the tank by rotating it counterclockwise and lifting it out. {Rgure3.5]
2. FIii the tank with 3 us cups/ 710 mL of distilled white vinegar. [Figure 3.6]
3. Replace the tank cover and swish the vinegar around the tank. {Rgure 3.7]
4. Place the tank on the base and soak for 15-20 minutes. Vinegar will drain into the base chamber and loosen scale (mineral buildup) in tile tank and in the base chamber (including the transducer and floaij. [Figure 3.8]
5. Remove the tank, remove the tank cover, and pour out any vinegar. [F,gure 3.9]
6. Flip the tank over and remove the noise silencer. To remove the noise silencer, press tile release tabs and gently pull away from the humidifier. [Figure 3.10]
7. Remove the float from the base chamber by pulling up one end ofthefloat lFigure3.7f]and pulling the shaft out from the fioat brackets. One side of the float brackets is open (U-shaped)to allow the shaft to be removed. [Figure 3.1
8. Place the fioat, water filter assembly, and noise silencer In a small container. FIii with enough vinegar to cover them. Soak for 15-20 minutes. [Rgure 3.13]
9. Use the cleaning brush and a soft cloth to remove scale from all parts.
10. Rinse all parts until any vinegar smell is completely gone. [Figure 3.14]
11. Dry all parts with a cloth. Make sure all parts are completely dry before reassembling or storing

Reassembling

1. Flip the water tank over and place the noise silencer back into the tank. [Figure 3.15]
2. Place the water filter assembly back into the tank and rotate it clockwise to secure it in place. [Figure 3.16
3. 3. Place the float back into the base chamber:
   • a. Make sure the correct side of the float is facing up. {Figure 3.17]
   • b. Insert the smaller prong Into the closed side of the float brackets. {Figure 3.18]
   • c. Place the larger prong into the open (U~haped) side of the fioat brackets.
4. Place the tank back on the base. Refill the tank, if necessary.
5. Place the tank properly on the base and place the tank cover on the water tank.

Storing
Follow the cleaning instructions (see page 6) and allow all parts to dry completely before storing. Store in a cool. dry location.

Replacing the Filter Assembly
If the filter assembly is damaged or water cannot flow into the base chamber, the filter or filter assembly needs to be replaced. For more information, contact Customer Support (see page 10).

FCC STATEMENTS

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT – PART 18
This device complies with part 1B of the FCC Rules.
This equipment generates and uses ISM frequency energy and If not Installed and used properly, that is In strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type testeo and found to comply with limits for an ISM Equipment pursuant lo part 18 of FCC Rules, which are designed to provide reasonable protection against such Interference In a residential lnstallatlon. However, there Is no guarantee that Interference will not occur In a particular instl!lletion. If this equipment does cause interference to radio or television reception. which cHn be determined by tuning the equipment off and on, the user Is encouraged to try to correct the lnterferenc.e by one or more of the follo\Wlng·

• Reorient the receiving antenna of radio or television.
• Relocate the equipment with respect to t he receiver.
• Move the equipment away from the receiver.
• Plug the equipment into a different outlet so that the equipment end receiver are on different branch circuits.

Conduct only the user maintenance found In this manual. Other maintenance and servicing can cause harmful Interference end cen void the required FCC compllance. The manufacturer Is not responslble for any radio or TV Interference cause by unauthorized mod ification to th9 equipm9nt. It is t h9 r0sponsibility of thA us9r to correct such interfer0nc0.

FCC SDOC SUPPLIER’S DECLARATION OF CONFORMITY
Arovast Corporatlon hereby declares that this equfpment is In compliance with the FCC Part 18 Subpart 8. The dec larat ion of conformity may be consulted in lhe support section of our We’o site, accessible f rom www.levoitcom

WARRANTY INFORMATION

Tenns & Policy
Arovast Corporation (“Arovast”) warrants this product to the original purchaser to be free from defects In material and workmanship, under normal use and conditions, for a period of 2 years from the date of original purchase. Arovast agrees, at our option during the warranty period, to repair any defect in material or workmanship o r furnish an equal product In exchange without charge, subject to verification of the defect or malfunction and proof of the date of purchase. There Is no other express warranty. This warranty does not apply:

• If the product has been modified from its original condition;
• If the pro duct has not been used in accordance with directions and Instructions in the user manual;
• To damages or defects caused by accident. abuse, misuse or improper or inadequate maintenance;
• To damages or defects caused by service or repair of the product performed by an unauthorized service provider or by anyone other than Arovast;
• To damages or defects occurring during commercial use, rental use, or any use for  which the product is not intended; To damages or defects exceeding the cost of the product.

Arovast will not be liable for Indirect, Incidental, or conseq uential damages In connection with the use of the product covered by this warranty.

This warranty extends only to the original consumer purchaser of the product and Is not transferable to any subsequent owner of the product regardless of whether the product is transferred during tile specified term of the warranty.

This warranty does not extend to products purchased from unauthorized sellers. Arovast’s warranty extends only to products purchased from authorized sellers that are subject to Arovast’s quality controls and have agreed to follow its quality controls.

All implied warranties are limited to the period of this limited warranty.
This warranty gives you spec ific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequentJal damages. so the above limitation or exclusion may not apply to you.

If you discover that your product is defective within the specified warranty period, please contact Customer Support Via support@levolt.com. 00 NOT dispose o f your product before contacting us. Once our Customer Support Team has approved your request, please return the product with a copy of the invoice and order ID.

Every Levo It product automatically Includes a 2-year warranty. To make the customer support process quick and easy, register your product online at www.levoitcom/warranty.

This warranty is made by: Arovast Corporation 1202 N. Miller St, Suite A Anaheim, CA 92806

Questions or Concerns?
Please contact us Mon-Fri, 9:00 am-5:00 pm PST/PDT at support@levoit.com or at 888-726-8520.

CUSTOMER SUPPORT

If you have any questions or concerns about your new product, please co ntact our helpful Customer Support Team.

• ADDRESS: Arovast Corporation 1202 N. MIiier St., Suite A Anaheim. CA 92806
• Email: support@levoit.com
• Toll-Free: (B88) 726-8520

Support Hours: Mon- Fri, 9:00 am- 5:00 pm PST/PDT
Please have your order invoice and o rder ID ready before contacting Customer Support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>