MiCODUS ML910G Tracker Long Battery 10000mah User Manual

: June 15, 2024
: MiCODUS

Table of Contents

Main Features
Specifications
Activate Device
Package Content
Functions Explanation
Installation Recomendation
Trouble Shootin
Full SMS Commands List
After-sale Contact Information
Download APP
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ML910G Tracker Long Battery 10000mah
User Manual

ML910G/ML920G User Manual V1.0
Learn how to set up your new MiCODUS Tracker

Main Features

Specifications

Device Information	Model	ML910G/ML920G
Weight	ML910G:306g ML920G:467g
Dimensions	ML910G: 115(L)65(W)31(H)mm

ML920G: 115(L)65(W)47(H)mm
Battery| 3.7V 10000/20000mAh Li-Polymer Battery
Working Parameters

| Battery Life| ML910G: Real-time Tracking mode: 12-15 days; Power Saving Mode: around 30 days; Hibernate Mode: around 60 days
ML920G: Real-time Tracking mode: 25-30 days; Power Saving Mode: around 60 days; Hibernate Mode: around 120 days
Working Temperature| -20°C – 600°C
Working Humidity| 5%-95%RH
Celluar Specifications| SIM Card| Normal Size
Celluar Antenna| Built-in
Working Frequency| 4G LTE CAT1: 131/B2/B3/64/B5/B7/B8/B28/666
2G GSM/GPRS: 850/900/1800/1900MHz
GNSS Specifications| GNSS| GPS+GLONASS+BDS
Hot/warm/cold Start| <35, <35s, <45s @ Open Sky
GNSS Antenna| Built-in Ceramics GNSS Antenna
Positioning Type| GNSS+LBS+AGPS
Accurancy| GNSS Accuracy: <5M @ Open Sky
LBS Accuracy: 100-2000m
(Depend on density of base stations)

Activate Device

First Step： Prepare and Install SIM Card

If use your local SIM card, please make sure the SIM card already enabled SMS, internet data traffic, call and caller ID displaying functions;
If use our spionlink SIM card, then please recharge it via this website www.spionlink.com to get data plan firstly

LED	Event	State
POWER LED (RED)	Charging	Solid
Charger inserted and battery has been fully charged	Dark
Charger has not been inserted	Dark
CELL LED (YELLOW)	Searching for network	Flash every 1 second
Network has been registered	Solid
GPS LED (Blue)	GPS is in fixing	Flash every 1 second
GPS has fixed	Solid
ALL LED	Device is working but stopped more than 5min	ALL LED TURN OFF

Device has not been turn on
Device ran out of battery

Second Step: Configure APN
Please get the exact correct APN name from local SIM card provider.Take the tracker to a good signal place for operation and configure the APN for it as below:

SMs Command Format	Reply	Example	Note
apn,apn content, apn ok apnuser,apnpasswd#	apn,ok	ange,orange, orange#	If

there has APN user and APN apnpassword, then please use this command for configuration
apn,apn content#| apn ok| apn,internet#| If there doesn’t have APN user and APN password, then please use this command for configuration

Note: The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply “SET APN ok”but it will can’t get online!

Package Content

ML910G or ML920G Tracker	x 1
USB Charging Cable	x 1
User Guide	x 1
Packing Box	x 1

Functions Explanation

Voice Monitor

Set up a center number for the device:
CENTER,A,CENTER NUMBER#
For example, if you want to set up this number as center number:+8613366668888, the command should be sent like this:
CENTER,A,+8613366668888# Note: Please put the country code as prefix with the center number!
Use the center number to set up a number for the tracker to call back: MONITOR,number for monitor#
For example, if your send this command:
MONITOR,+8613366668888#,then the tracker will make a call to this number +8613366668888 and this number can pick up the call to monitor the voice around it.
1. Set Working Mode
Command format: MODE,A,T1,1T2#
For example: Realtime Tracking Mode: MODE,1,10,3600#
This means the tracker will upload every 10 seconds when it is moving, and every 3600 seconds when it is static.
For example: Power Saving Mode: MODE,2,0800,1#
For example: This means the tracker will enter into power saving mode at 08:00am and upload every 1 hour. If now is 09:00am, then the tracker will enter power saving mode at 08:00am of tomorrow.
For example: Hibernation Mode: MODE,3,0800,1#
This means the tracker will enter into power saving mode at 08:00am and upload every 1 hour.
Note: The difference between the mode 2 and mode 3 is that, under mode 2, the device can be waked up by sms, call and light sensor, under mode 3 the device will just can be waked up by light sensor.
1. Vibration Alarm
Set up a center number for the device: CENTER,A,CENTER NUMBER#
For example, if you want to set up this number as center number:+8613366668888, the command should be sent like this:
CENTER,A,+8613366668888#
Note: Please put the country code as prefix with the center number!
Set up SOS contact numbers: SOS,A,SOS1,SOS2,SOS3#
For example,: SOS,A,+8613366667777,
+8613366667778,+8613366667779#
Note: You can set up 3 SOS alarm numbers for the device at the same time
Set up the vibration alarm way: SENALM,ON,2#

Installation Recomendation

Driving seat sundries box
Front bumper
Driving sundries box
Under the chassis
Rear windscreen
Rear bumper

Trouble Shootin

Type	Use
Unable to connect to tracking platform	Check the APN and settings.

Check whrther the data service of SIM card is enabled.
Check the balance of SIM card.
Tracker shows oﬄine| Check whether external power is still connected.
Check if the vehicle entered netword blind area.
Check the balance of SIM card.
Unable to locate| Make sure the top side facing upward without metallic
Make sure it’s not in area with no satellite coverage things shielded.
Location drift| In area with poor GNSS signal (tall building around or basement), drifting may happen.
Check whether vibration happens around to trigger the accelerator.
No command reply| Make sure command format is correct.
Vehicle may be in network blind area.
Make sure SIM card is well inserted and has SMS servi

Full SMS Commands List

Query Commands

Functions	Command Format	Example
Version Inquiry	VERSION#	Device Reply Example:

ID: ID number of the tracker
IMEI: IMEI number of the tracker
ICCID: The ICCID number of the SIM card in the tracker VERSION:The firmware version of the tracker
Parameter Inquiry| PARAM#| Device Reply Example:
ID: ID number of the tracker
IMEI:IMEI number of the
ICCID:The ICCID number of the SIM card in the tracker APN:APN name,APN user,APN password,
IP: Domain name and port number or IP address, port pumber
MODE:Working mode;interval or starting time, upload interval
SPEEDLIMIT:The overspeed threshold
ANGLERPT: Data uploading angle
CENTER: Center number of the tracker
SOS: SOS1,SOS2,SOS3
GMT: Time zone
Status Inquiry| STATUS#| BATTERY: XX% (Built-in Battery Power Percent) INTERNET: CLOSED (No Network)
FAILED (Connecting Network or Failure)
SUCCESS (Connected to Network)
NET: NONE (No GSM Signal),HIGH/MED/LOW
(Signal Strength) 18
GPS: CLOSED(GPS Module Closed),FIXED,N(Positioned and satellite number),UNFIX,O(Not Positioned yet) SPEED: 30KM/H(The current speed of the target) SENSOR: ON/OFF (Sensor on or off),
LEVEL: 3 (Sensitivity level 1-9)
STATE: ARM (Arm or Disarm)
Alarms Parameters| ALARM#| ID: 19172012644(Device ID number)
STATE: ARM(DISARM)(Fortified state of device) SPEED: ON(OFF);30km/h(speed limit); alarm ways SHIFT: ON(OFF);300m(shift limit);alarm ways
VIBRATE: ON(OFF);3(sensitivity of sensor);alarm ways LOW BATTERY: ON(OFF);alarm ways
TEARDOWN: ON(OFF);alarm ways
Latitude& Longitude Inquiry| WHERE#| LAT:N23.02930,LON:E114.32180,SPEED:0.00KM/ H,DATETIME:2023-01-05 14:39:11
Map URL Inquiry| URL#| http://map.google.com/?q=22.557868,113.935090<0.0km/h0.0<2023-01-05 14:39:11>IMEI:354188047752402

Setting Commands

Functions	Command Format	Example
APN Setting	APN,APN Name, APN User,
APN Password#	Example:

APN,CMNET#
(if no APN User & APN Password) APN,internet,internet,internet#
(if with APN User & APN Password)
Server Setting| If set with Domain Name.
SERVER,1,Domain,Port# ‘| SERVER,1,d.micodus.net,7700#
If set with IP: SERVER,0,IP,Port#| SERVER,0,47.254.77.28,7700#
Restore factory settings| FACTORY#| FACTORY OK
Restart device| RESTART#| RESTART OK
Internet Traffic Switch| TRAFFIC,ON#| OPEN TRAFFIC OK
TRAFFIC,OFF#| CLOSE TRAFFIC OK
Set the angle upload| ANGLEREP,X,A,B#| Example: ANGLEREP,ON,30,3# ( Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds) X=ON/OFF, default:ON; A=5,-180 degrees, diversion angle degree, default:30 degrees:B=2–5 seconds, detecting time, default:3 seconds,
ANGLEREP,OFF#| CANCEL UPLOAD ANGLE OK
Time Zone Setting| GMT,Time zone orientation,Whole Time Zone
Half Time Zonel#| Example:GMT,E,8#(if no half time zone) GMT,W,9,30#(if has half time zone)
NOTE: Parameter : E / W: 0 — 12; 0/15/30/45
Mileage Statistics| M I LEAGE,A,B#| A=ON/OFF, On/Off mileage calculation, default: Off B=0″-999999,Mileage initial value , unit: km ; default: 0, mileage return to zero
M I ELEAGE#| Query current mileage
Add SOS Administrator Number| SOS,A,1 st number, 2nd number,
3rd number#| Set 3 numbers at a time:
SOS,A,13800138000,13800138001,13800138002#
Set the first number separately: SOS,A,13800138000#
Set the second number separately: SOS,A„13800138001# Means to set 3rd number separately:
SOS,A„,13800138002#
Delete SOS Administrator Number| SOS,D,1st number, 2nd number, ‘
3rd number#
or SOS,D,1,2,3#| delete the number: SOS,D,13800138000# Delete 1st number: SOS,D,1#
Delete 2nd number: SOS,D,2#
Delete the 2nd and 3rd number: SOS,D,2,3#
Add Center Number| CENTER,A,center number#| Example: CENTER,A,+8613800138000#
NOTE: Please set up the center number with the country code as prefix!
Delete Center Number| CENTER,D#| DEL CENTER OK
Sleep Mode Setting| SLEEP#| NOTE: After set this sleep mode, the device will enter into sleep mode automatically when the device keep stationary status more than 5min.
SLEEP,OFF#| CANEL SLEEP MODE OK
Voice Monitor| MONITOR,N#| Example: MONITOR,+8613366669999# ( Means the tracker will make call to +8613366669999, and this number +8613366669999 can pick up the call to monitor the voice ) N: Number for Voice Monitoring
NOTE: 1. Please send this monitor command via the center number;
2. Any number can be set up to monitor the voice, the tracker will make a call to the number N and it will can pick up the call to monitor voice
Working Mode Settin| MODE,A,T1,T2#| A=1/2/3, 1: Tracking mode 2: Power saving mode
3: Hibernation mode; Default mode: 1
A=1 (For example: MODE,1,10,3600# means the tracker will work under mode 1, it will upload every 10s under
moving status and 3600s under static status)
T1: upload interval of GPS data in moving status, unit: second,10-3600s; default: 10s
T2: upload interval of GPS data in static status, unit: second, 180-65535s; default: 3600s
unit: second, 180-65535s; default: 3600s
A=2 (For example: MODE,2,0800,1# means the tracker will work with power saving mode since the next 08:00am, and upload every 1 hour )
T1: interval start time,format: HH:MM
T2: time interval,range: 1-72 unit: hour,default interval: 24hours
A=3 (For example: MODE,3,0800,1# means the tracker will work with hibernation mode since the next 08:00am, and upload every 1 hour )
T1: interval start time,format: HH:MM
T2: time interval,range: 1-72 unit: hour,default interval: 24hours
NOTE: The difference between Mode 2 and Mode 3 is that under Mode 2 the device can be wake up by SMS, Call and light sensor, but under Mode 3 the device just can be wake up by light sensor!
Heartbeat
Packet Upload| HBT,time#

| Example: HBT,3# ( Means the tracker will send hearbeat
data package to server very 3min to keep the network connected )
Time: 1-60min, default 3min
Sensor Sensitivity| SENLEVEL, sensitivity#| Example: SENLEVEL,4#
( Means shake sensor level is set to 4 ) A=1-9
NOTE: 1-9 is from week to strong vibration

Alarm Setting Commands

Functions	Command Forma	Example
Vibration Alarm Setting	SENALM,A,M#	Example: SENALM,ON,2# ( Means the

vibration alarm already been enabled and the alarm message will be sent
via Server, SMS and Call )
A=ON/OFF, default: OFF;
M=0/1/2, way of alarming, 0 :GPRS only,1: SMS+GPRS,
2: GPRS+SMS+phone call, default:1
SENALM,OFF#| CANEL VIBRATE ALARM OK
Overspeed Alarm Setting

| SPEED,A,B,M#| Example: SPEED,ON,120,1# ( Means the speed limit is 120km/h and the alarm way is via SMS and Server )
A=ON/OFF, open or close over speed alarm, default： OFF B=1～ 255(km/h), speed limit, default： 100(km/h);
M=0/1/2, way of alarm, 0 : GPRS only, 1: SMS+GPRS, 2:GPRS+SMS+CALL; default: 1
SPEED,OFF#| CANCEL OVERSPEED ALARM OK
Shift Alarm Setting

| SHIFT,A,B,M#| Example: SHIFT,ON,100,1#( Means Setting 100 meters
shift alarm range, when the ignition turned off, vehicle’s
100 meters’ shift will trigger the alarm and the alarm
message will be sent via Server and SMS )
A=ON/OFF; default:ON
B=Shift Distance (Range: 100-9999m)
M=0/1/2; way of alarm, 0 : SERVER only, 1: SERVER+SMS,
2: SERVER+SMS+CALL, default:1
SHIFT,OFF#| CANCEL SHIFT ALARM OK
Low Battery Alarm Setting| BATALM,A,M#| Example: BATALM,ON,1# ( Means the low battery alarm
already been enabled and the alarm message will be sent
via Server and SMS )
A=ON/OFF,default: ON;
M=0/1/2, way of alarming,0: SERVER
only,1: SERVER+SMS, 2: SERVER+SMS+Call, default:1；
NOTE: Once the battery level is below 20% device will alarm
BATALM,OFF#| CANCEL LOW BATTERY ALARM OK
Disassemble
Alarm Setting| TEARDOWN,A,M| Example: TEARDOWN,ON,2#( Means the teardown alarm
already been enabled and the alarm message will be sent
via Server, SMS and Call )
A=ON/OFF; default:ON
M=0/1/2; way of alarm, 0 : SERVER only, 1: SERVER+SMS,
TEARDOWN,OFF#| CANCEL DISASSEMBLE ALARM OK