AVENTON Fanttik X8 Apex Air Inflator User Manual

June 5, 2024
AVENTON

Fanttik
X8 APEX AIR INFLATOR
User Manual

Model: X8 APEX
Read this manual carefully before use and keep it for future reference.
Thank you for purchasing the X8 APEX air inflator. With its large LED screen and easy-to-use interface, this is a highly capable inflator fit for a wide range of tasks.

PRODUCT OVERVIEW

1. Battery indicator
2. Real-time pressure value
3. Target pressure value
4. Power button
5. Light button
6. Preset mode| 7. Pressure unit
8. “+” button
9. Mode button
10. “2 button
11. Air outlet
12. USB-A port
13. USB-C port
---|---

PACKAGE CONTENTS

Essential Version

Carefully check the package contents. If anything is missing or damaged, please contact online customer service for support.

BATTERY LEVEL INDICATOR & CHARGING

Battery Level Indicator


The battery level is shown by four bars, with each bar representing 25%.
1 bar = under 25%
2 bars = between 25% and 50%
3 bars = between 50% and 75%
4 bars = between 75% and 100%
Note: The battery indicator will flash when the battery level is below 20%.
Charging

Fully charge the inflator before using it for the first time. To charge, connect it to a certified 5.0V/3A USB charger with the charging cable.
While charging:
1 bar flashing = under 25%
1 bar solid, 2nd bar flashing = between 25% and 50%
2 bars solid, 3rd bar flashing = between 50% and 75%
3 bars solid, 4th bar flashing = 75% and 100%
All 4 bars solid = fully charged
The inflator will automatically switch off if left inactive for 5 minutes after being fully charged.
Note:

  • The inflator cannot be used while it is charging.
  • The USB charger is sold separately. Make sure to use a certified charger.

TURNING THE INFLATOR ON/OFF

ON
Long-press for 1.5 seconds to turn on.
OFF
When the inflator is turned on, long press 1.5 seconds to turn off.
The inflator will automatically turn off in the cases below:

  1. After 3 minutes of inactivity.
  2. When the charging cable is disconnected during charging.
  3. After 5 minutes of inactivity after being fully charged.
  4. When the inflator is being used as a power bank, after disconnecting the other device.
  5. Inflate over 5 minutes when the target pressure value is below 5psi.
  6. Inflate over 3 minutes when the target pressure value is above or equates 120psi.

CONNECTING THE AIR TUBE AND NOZZLE

Connecting the Air
Tube Connect one end of the air tube (with screw thread) to the inflator before inflating.
Schrader Valve
Tires on cars, motorcycles, e-bikes, and most mountain bikes use a Schrader valve.
To inflate: The inflator can be directly connected to a Schrader valve to start inflating.
To deflate: Use an proper tool (such as 4mm Allen wrench) to press the pin inside the air valve to release air.

Presta Valve Adapter
Road bicycles and certain mountain bikes use a Presta valve which requires the included
Presta valve adapter to be used.
To inflate:

  1. Connect the Presta valve adapter to the Schrader valve of the air tube.
  2. Unscrew the ring of the Presta valve of the tire.
  3. Connect the Presta valve adapter to the tire’s Presta valve to start inflating.

To deflate: Unscrew the ring of the tire’s Presta valve, and press the valve stem down to release air.

Needle Valve Adapter

To inflate balls like basketballs and footballs, the included needle valve adapter will need to be used.
To inflate: Screw the needle valve adapter onto the Schrader valve adapter, then insert the needle into the valve of the ball to start inflating.
To deflate: Insert the needle valve adapter into the valve of the ball, and gently apply pressure to the ball to release air.

DETECTING THE CURRENT PRESSURE

When the inflator is turned on, connect the air tube to the device to be inflated, and then the I FD screen will disnlav the current pressure value.

DETERMINING THE RIGHT PRESSURE VALUE

To avoid injuries from bursting items due to over-inflation, make sure you are aware of the maximum inflation pressure before you start.

Tires

The recommended air pressure of tires for cars, bicydes, and motorcycles is indicated on the tire’s sidewall. The recommended tire pressure for cars is also indicated on the inside of the driver’s side door.
For details concerning load carrying capacity and recommended air pressures, refer to your vehicle’s instructions or manual.

Balls

The recommended air pressure for footballs, basketballs, volleyballs, and other balls is indicated near the ball’s air valve.

Air Pressure Reference Table

Category Type Recommended Pressure Range
Bicycles Electric Folding Bike tires

12-, 14-, & 16-inch bicycle tires
20-, 22-, & 24-inch bicycle tires
26-, 27.5-, & 29-inch mountain bike tires
Electric Scooter tires
700c road bike clincher tires
700c road bike tubular tires| 10 – 50psi 30 – 50psi 40 – 50psi 45 – 65psi 40 – 50psi 100 – 130psi 120 – 145psi
Motorcycles| Scooter & street motorcycle tires| 1.8 – 3.0bar
Cars| Car tires| 2.2 – 2.8bar
Balls| Basketball Soccer ball Volleyball Football| 7 – 9psi
8 – 16psi 4 – 5psi 12 – 14psi

Note: Pressure range values are for reference only. Always refer to the instructions or manual of the item being inflated for actual inflation pressure specifications. (The data above is from the QiCYCLE lab.)

PRESET PRESSURE VALUE

Switch Modes
Click the Mode button to switch between the five inflation modes below. Long press the Mode button to cycle through psi/bar/kPa. The number on the top of the screen indicates the real-time pressure of the inflated device, and the number on the bottom indicates the preset pressure.
Manual mode: When in the manual mode, no mode icon is selected on the screen. The preset pressure value is adjustable, and the value and unit will be saved. Adjustable Range: 3-150psi / 0.2 – 10.3bar
Car Mode: Default 2.5bar
Adjustable Range: 1.8-3.5bar
Motorcycle Mode: Default 2.4bar
Adjustable Range: 1.8-3.0bar
Bicycle Mode: Default 45psi
Adjustable Range: 30-145psi

Ball Mode: Default 8psi
Adjustable Range:4-16psi
Note:
When you have finished inflating an item, the manual mode will remeber the target pressure value as its default pressure value.
For the best inflating experience, we suggest you inflate items like balls via the ball mode.
Adjusting the Preset Pressure

After selecting a mode, press + or – to increase or decrease the target pressure value. Press and hold the + or – button to quickly adjust the pressure value.

LIGHT

Press the light button to turn the inflator’s light on/off. The light makes it easy to see in the dark when you have on any tasks, such as connecting the air compressor to a valve. When the light is on, press the light button to cycle through Spotlight, SOS and OFF.
Note: After 30 minutes, the light will automatically turn off.

INFLATING

Start Inflating

Press the Power button to start inflating. When inflating, the air compressor may be as loud as 75 – 80 dB. Please take appropriate precautions to protect your hearing. The air compressor and air tube can get very hot after running for a while. Avoid prolonged skin contact with the tube to prevent injuries.
Stop Inflating
Once the target pressure value has been reached, the inflator will automatically stop inflating. The inflator can also be manually stopped at any time by pressing the power button while inflating.
Caution
Items such as balloons, beach balls, and swim rings cannot be automatically inflated because they have an air pressure requirement below the air compressor’s minimum pressure range. Only inflate these items manually with caution.
Battery Information
The inflator’s battery lasts about 40 minutes on a full charge, running without a load at an ambient temperature of 25°C. Using the air compressor under a heavy load or at lower ambient temperatures may reduce its battery life.

DISCONNECTING THE AIR TUBE

The air compressor’s air hose may get very hot after inflating. To prevent injuries, exercise caution when disconnecting it from a valve. Some air may leak out of the valve when disconnecting the air compressor. To avoid pressure loss, quickly disconnect the air hose from the valve.

POWER BANK FUNCTION

This inflator can be used as a 5V/2A power bank when it is not being charged or inflating other devices. The battery needs to have a reasonable level of charge in order to work as a power bank.
Note: The inflator should be turned on when being used as a power bank. When being used as a power bank, the inflator will enter “Energy Saving” mode if inactive for 3 minutes, and the screen will only display the battery level icon. In energy saving mode, when disconnecting the charged device from the inflator, it will automatically turn off.

TROUBLESHOOTING

Problem Solution
Slow inflation speed 1. Check whether the air compressor’s battery level is

sufficient.
2. Check whether the air hose is leaking.
3. Check whether both ends of the air hose are securely connected.
4. Check whether the item that is being inflated is leaking
Air compressor turns on but does not inflate| 1. Check whether the air compressor’s battery level is sufficient.
2. Check whether the pressure of the item being inflated exceeds the preset pressure.
Unable to increase or decrease the preset pressure| Make sure the air compressor is set to the correct mode. Manual mode has a blank display without any icons and allows you to adjust the preset value within the range of 3 -150 psi.
The inflator inflates normally but the displayed pressure is zero| The pressure of low-pressure inflatables including balloons is too low to be measured.
Problem| Solution
---|---
Air leakage after connecting the air tube| Make sure the air hose is securely connected.
The battery level indicator is different when inflating compared to standby state| The lithium battery’s voltage level significantly drops when discharging power, causing the battery level indicator to have a different display when inflating compared to standby state. This is normal.
The battery level indicator doesn’t show on the  screen after charging| Use a certified adapter and the included charging cable, and try charging again.
The inflator cannotcharge other devices.| 1.  Make sure the remaining battery level is sufficient.
2.  The discharging output is 5V/2A. Make sure this output meets the requirements of the charged device.
3.  The inflator can not charge other devices while inflating.
None of above. The inflator doesn’t react with any input| Simultaneously press the light button and mode button to restart the inflator.

SPECIFICATIONS

Name Air Inflator
Model X8 APEX
Executive Standard QXMQJ0002-2019
Dimensions 200.5×63.5×63.5mm(Excluding air tube)
Inflation Pressure Range 3-150psi / 0.2-10.3bar
Operating Temperature Charging: 0`C-45t,Discharging: -10;C-415t
Storage Temperature -10’C–45t
Air Valve Dimensions Length 350mm
Battery Capacity 2600mAh(28.86 Wh)
Working Noise Lower than 80dB within 1 meter
Input 5V/3A
Output 5V/2A
Input Port USB Type-C
Output Port USB-A
Charging Time <4hours
Sensor Accuracy ±2psi

SAFETY INSTRUCTIONS

  • This product is not a toy and should not be used by children. Users should be above 16 years old.
  • Keep a safe distance between children and the inflator while inflating. There is a built-in lithium battery inside the product. Don’t place the product in fire or dump the battery.
  • Overheating, damage, or water may increase the risk of fire or explosion. It’s best to keep the product away from heat sources, and not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a chance it could explode.
  • Please store the product in temperature ranging from -10°C-45°C. Extremely hot or cold environments may damage the battery and shorten the lifetime of the inflator.
  • Long-time storage of the product may decrease the effectiveness of the battery. Charge the inflator at least once every three months to maintain its performance.
  • The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
  • If there is an unusual noise or the temperature becomes very high during inflating, please turn off the inflator immediately.
  • Before setting the inflation pressure value, make sure the pressure unit is correctly selected. Mixing up psi and bar could lead to dangerous overinflation.
  • Unit conversion: 1bar = 14.5psi, 1bar = 100kPa
  • Do not leave the inflator unattended while it is in operation.
  • Please use the product in a dry and clean environment. The intrusion of sand and dust may cause damage to the product. Don’t wash the product with water. Please use a certified 5V/3A adapter and the included charging cable to charge this product. Malfunction caused by actions not in accordance with the above requirements is not covered by the warranty.
  • After running for a long time, the temperature of the junction between the air tube and the main body can become very high. To avoid burns, avoid touching it.
  • This inflator is equipped with short circuit protection. Do not connect its USB-A port with its USB-C port.

Caution: To reduce the risk of electric shock, do not expose to rain. Store indoor.

WARRANTY CARD

Your Warranty Includes

  • 12-Month Coverage

Within 12 months of purchase, we will provide timely and effective online after-sales service. We will repair or replace any defective product (due to manufacturing fault) within the warranty period.

How to Return Your Fanttik Product

  • Contact info@aventon.com with your order number.
  • We will issue you a return label for your return.
  • Tear off the ‘Return Details’ page and fill in the details. Include this inside your return package.
  • We will issue your replacement/refund on receiving the return

****info@aventon.com ****www.aventon.com

Return Details
In order to process your return as quickly as possible, we require the following information. Please fill out this form and include it in your return package

Purchase Name:|
---|---
Order Number:|
Date of Purchase:|
Your Email Address:|
Place of Purchase:|

0 If your purchase was fulfilled by Amazon, please use Amazon’s 30-day return service.


Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals