FALCON RIDGE HO-1000-WD05 Care of Honda 1000 Aero-Vent Polycarbonate Windshield Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
HO-1000-WD05 Care of Honda 1000 Aero-Vent Polycarbonate Windshield
Instructions for Installation and Care of Honda 1000 Aero-VentPolycarbonate
Windshield HO-1000-WD05
NOTICE: Please check the contents of the package for any damage and make
sure all parts fit correctly and you are happy with the product before
removing the protective film. Once the film is removed you cannot return the
product for a full refund.
Be sure to read these instructions thoroughly before opening and installing
the Honda 1000 Polycarbonate Windshield.
- Check over the parts included in the cartons with the parts list shown below:
1 7/8” Loom Clamps| 2 each
---|---
1 3/4” Loom Clamps| 4 each
1” SS Bolts| 11 each
1 1/4″ SS Bolts| 2 each
Nylon Bolts| 5 each
Stainless Steel Washers| 20 each
Slide Fasteners| 8 each
Lock Nuts| 5 each
Plastic Thumb Nuts| 8 each
Sliding Vent Panels| 2 each
60” Rubber Gasket| 1 each
Bent Lexan Braces| 1 each
Lexan Windshield| 2 Pieces
If any parts are damaged or missing please contact customer service at 606-845-7439.
- Start by pulling it out of the box and find a clean area to lay it down and install the hardware. Next take the rubber gasket and starting at one end firmly place it along the entire bottom edge of the lower Windshield Section. You will need to peel back the protective film from the edge to install the gasket. If you leave the bulk of the protective film on while installing you can keep from scratching the windshield.
- Next, Install the Aero-Vent sliders as shown in the diagram below.
- Now install the lower portion to the upper portion using the nylon bolts. There are five holes in both sections with the holes in the upper portion being bigger. Set the upper portion on top of the lower portion and screw them together making sure that the slots on the ends are lined up. The photo on the next page shows how this looks.
- It’s time to install the windshield on the vehicle. There are three slots on either side, the top slot gets a 1 7/8″ clamp and the bottom two get 1 3/4″ clamp. Start with the bottom and top slots using 1″ bolts, washers, and a thumb nut as shown in the diagram below.
- The middle Slot is where the two pieces overlap. Connect this the same as the other two except using the 1 1/4″ bolt instead of the 1″. See the photo below.
- Next, take the bent Lexan brace and install it on the windshield. Please see the diagram below.
- Now you are ready to take it out and enjoy. To clean the windshield, always clean using a liquid of some sort to decrease the chance of scratches. We recommend using microfiber cloths that are readily available at any dollar store. Any window cleaner will work fine; just remember to use a soft clean rag or micro-fiber cloth to clean it.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date the item is received. You MUST package the product
exactly as it was originally packaged from the factory to get a full refund
for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory-new condition. NOTE: All windshields must be returned with the original protective film intact and not removed. Do NOT REMOVE it if you have any intentions of returning the item. Refund/ replacement of a windshield will only be processed on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable condition (any returned items that have been used, altered, or damaged in any way will not be subject to a refund.) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, a credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping costs will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defects in the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>