ca Go FS200 Life Infant Sling Mount Instruction Manual

ca Go FS200 Life Infant Sling Mount

Product Information

The Infant-Sling-Mount is designed for the FS200 Life and enables the safe installation of an Infant-Sling. It is suitable for infants aged 0 to 9 months and weighing up to 9 kg. The mount  can be placed on the left, right, or centrally in the transport box. It allows for the transportation of up to two children or one child and one infant. The mount can be hung in the direction of travel or against it, with installation against the direction of travel recommended for better absorption of inertia forces.

Intended Use

• The Infant-Sling-Mount is specifically designed to securely install an Infant-Sling in the FS200 Life. It can be installed centrally in the transport box or on the left or right side, depending on preference. It is important to ensure that the Infant-Sling-Mount is suitable for the intended fastening system and can be tied down safely.
• Every child and infant must be transported in a child seat or Infant-Sling suitable for their specific height and weight. They must be strapped in at all times. Transporting infants and children with the box closed or installing the transport box lid is not permitted.

Scope of Delivery

1. Adapter discs – 4 pieces
2. Cylinder head screw, M6 x 25 – 4 pieces
3. O-rings – 4 pieces
4. Washers – 4 pieces
5. G-hook, left – 2 pieces
6. G-hook, right – 2 pieces
7. Connector plate without loops (type B) – 1 piece
8. Connector plate with loops (type A) – 2 pieces
9. Connecting strap – 2 pieces
10. Lashing strap with three-bar buckle – 2 pieces
    Note: Item 7, one item 8, and both items 10 are supplied pre-installed.

Product Usage Instructions

1. Start by identifying the desired position of the Infant-Sling-Mount in the transport box: centrally, on the left side, or on the right side.
2. Ensure that the Infant-Sling-Mount is suitable for the intended fastening system and can be tied down safely. Check the operating instructions and specifications of the mount.
3. If only an infant is to be transported in the transport box, it is recommended to install the Infant-Sling-Mount in the central position.
4. Use the provided tools, specifically a 5 mm Allen key, for assembly.
5.  Follow the assembly steps described in the separate assembly instructions for your FS200 Life. These instructions will provide more detailed guidance on how to install the Infant-Sling-Mount.
6. Ensure that every child and infant is transported in a suitable child seat or Infant-Sling that corresponds to their specific height and weight. Strap them in securely at all times.
7. When transporting infants and children, do not close the transport box or install the transport box lid.
8.  If another child is to be transported next to the Infant-Sling-Mount, use the Ca Go child seat.
9.  It is recommended to install the Infant-Sling-Mount against the direction of travel for better absorption of inertia forces.

Safety notices

This user manual contains various types of notice. The notices are designed as follows:

• Danger
  Potential hazards for your health and the health of your co-riders and other road users if you fail to observe the respective instructions or do not take corresponding precautions.

• Notice
  Provides information about how to handle the product or refers to a passage in the user manual that deserves special attention.

• Caution
  Warns you about incorrect behaviour that can result in material and environmental damage.

• Separate instructions
  Refers you to other assembly instructions for your FS200 Life which describe the respective assembly step in more detail if needed.

General information

The Infant-Sling-Mount enables the safe installation of an Infant-Sling in the FS200 Life. It makes it possible to transport infants aged 0 to 9 months and weighing up to 9 kg in the FS200 Life.

If the Infant-Sling-Mount is placed on the right of left side, another child can be transported next to it, in the Ca Go child seat.

Intended use$

• The Infant-Sling-Mount is designed to install and secure an Infant-Sling in the FS200 Life. The Infant-Sling-Mount can be installed centrally in the transport box or on the left or right side, according to preference. If only an infant is to be transported in the transport box, we recommend installing the Infant-Sling-Mount in the central position.
• Every child and every infant must be transported in a child seat or Infant-Sling that is suitable for his or her specific height and weight. They must be strapped in at all times. The FS200 Life is designed for the transport of up to two children, or one child and one infant.
• The Infant-Sling-Mount can be hung into the transport box either in the direction of travel or against it. We recommend installation against the direction of travel, since this will allow the structure to better absorb any inertia forces.
• The Infant-Sling-Mount is designed for infants aged 0 to 9 months and weighing up to 9 kg. Beyond this specification, the operating instructions and specifications of the respective Infant-Sling-Mount must be observed. It is important to check and ensure that the Infant-Sling-Mount is suitable for the intended fastening system and can be tied down safely.
• Transporting infants and children with the box closed is not permitted. When transporting infants and children, the transport box lid must not be installed.

Scope of delivery

1. Adapter discs
   4 pieces

2. Cylinder head screw, M6 x 25
   4 pieces

3. O-rings
   4 pieces

4. Washers
   4 pieces

5. G-hook, left
   2 pieces

6. G-hook, right
   2 pieces

7. Connector plate without loops (type B)
   1 piece

8. Connector plate with loops (type A)
   2 pieces

9. Connecting strap
   2 pieces

10. Lashing strap with three-bar buckle
    2 pieces
    Item 7 , one item 8 and both items 10 are supplied pre-installed.
    Assembly requires the following additional tools: 5 mm Allen key

Installation

To install the set, install one connector plate to the bolting points in the top transport box rails at the front and rear (Figs. 4 and 5).

• At the head of the Infant-Sling-Mount, use a connector plate with loops (type A) 8 .
• At the foot of the Infant-Sling-Mount, install the height-adjustable fastener from items  7 , 8 and 10 .

Installation on one side, against the direction of travel

Installation in the centre, against the direction of travel

• Place a washer 4 under the head of each cylinder head screw 2 and push the screw through the connector plates. The hole positions to be used in the connector plates depend on the installation position in the box (Figs. 6, 7, 8 and 9).

• Each screw shaft receives one adapter plate 1 behind the connector plate, with the concave side facing the rail. Secure the screw thus inserted with an O-ring 3 . Now secure the connector plates at the front and rear to the top rails (5 mm Allen key, 5–8 Nm tightening torque) (Figs. 6, 7, 8 and 9).

• The lashing straps 10 have already been looped in at the top connector plate 7 and the central connector plate 8 . They are looped around the transport box bottom rail (Fig. 10).

• Following this, guide the lashing straps through the three-bar buckle from behind and pull them tight (Fig. 11).
  Make sure to pull the belt straps sufficiently tight.

Height adjustment and hanging in the Infant-Sling-Mount

• The height of the connector plate 8 can be set to one of three levels according to preference. Loosen the belt straps, set the plate height and pull the belt straps tight again (Fig. 12).

• Thread the connecting straps 9 into the Infant-Sling-Mount, then place one right G-hook and one left G-hook ( 5 and 6 ) at the ends (Fig. 13).

• Fully hang the Infant-Sling-Mount with the G-hooks into the loops at the foot, so that the hook at the front end has a lateral hold in the loop (Fig. 14).

• In the same way, hook the G-hooks into the closed loops at the head (Fig. 15).

• As a final step, pull the belt straps tight (Fig. 16).

Before every ride, ensure that all G-hooks are hooked in properly and all belts pulled tight, since the Infant-Sling-Mount might unhook itself unexpectedly if the belts are too loose. Also, the Infant-Sling could slide around or move too freely within the transport box. This could lead to shock- type loads on the infant, resulting in a potential injury hazard.

General notes on care

The components of the Infant-Sling-Mount should be cleaned only with water and mild detergents, such as soap.

• Never use aggressive cleaning agents, acids or solvents to clean the set. Such substances can corrode surfaces or damage the belts. This may affect the stability of the components.
• The components of the Infant-Sling-Mount must be checked for damage at regular intervals. If belt straps have become frayed, they must be replaced. Retighten any loose screw connections to 5 to 8 Nm.

Statutory warranty / guarantee

• The legal statutory warranty applies. You can find more details on the warranty on our website: www.cagobike.com/en/warranty
• Export to the USA and Canada is not permitted (product liability)!

Service

If you have questions concerning this user manual, please contact your Ca Go dealer or your Ca Go service team.

AOUT COMPANY

• Ca Go Bike GmbH
• Am Autobahnkreuz 7
• 56072 Koblenz
• Germany
• +49 261 914090-600
• info@cagobike.com
• www.cagobike.com
• Managing directors: Franc Arnold
• Company register
• Court of record: District Court Koblenz / register no.: HRB 26998 / VAT Id no. DE326206636
• Responsible for distribution and marketing of the user manual: Ingo Kahnt
• Ca Go Bike GmbH reserves the right to change product specifications without prior notice.
• Typographical errors, mistakes and modifications reserved. Version of 03/2023
• ©Reproduction, reprint and translation, as well as any use for economic purposes (including as extracts, in print or electronic form) without prior written approval is forbidden.

References

• E-Lastenrad für dein wertvollstes Cargo | Ca Go Bike
• Warranty | Ca Go Bike

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>