FALCON RIDGE BH-4400-FC01 Bush Hog Trail Hand TH4400 4×4 and TH4200 4×2 Full Cab Enclosure Instruction Manual

BH-4400-FC01 Bush Hog Trail Hand TH4400 4×4 and TH4200 4×2 Full Cab Enclosure
Instruction Manual

Notice: Do not smoke inside the cab or expose the enclosure to direct flames. The cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to installation.

1. Carefully open the carton and remove the rolled Cab Enclosure on a large flat surface that is clean and free of dirt or other material that may soil or scratch the windows of the Cab.
2. It will help to unhook the hood and raise the bed prior to installing the cab enclosure
3. Check over the parts included in the carton with the parts list shown below:
   Velcro Hook strips:
   “ “
   “ “
   “ “
   Snap Studs
   Cab Enclosure| 2 each
   4 each
   1 each
   2 each
   7 each (1 extra)
   1 each| 3” long
   8” long
   18” long
   12” long
   ---|---|---

If any parts are damaged or missing please contact customer service at 606-845-7439.

4. Loosely drape the Cab Enclosure over the Trail Hand roll cage. Note the correct position for the 18” Velcro Hook strip is on the underside of the front edge of the Trail  Hand hood. Clean the area with Isopropyl alcohol let it dry and apply the Velcro hook strip. Then attach the Cab to the strip under the Hood.
   As shown in the photo below:
   

5. Next, raise the bed and place the two 12” adhesive Velcro strips across the bottom rear of the cab, aligning with Velcro on the rear of the cab. Now pull down on the rear of the cab enclosure and affix to the Velcro.

6. Now zip the doors up and make sure that the cab is centered correctly, you may have to detach the front and rear Velcro to adjust and center everything.

7. Note the position and install four 8” and two 3” Velcro tabs on the left and right side of the roll cage for the front window. Be certain to clean the surfaces before applying the adhesive hook strips! First, apply all three strips on one side of the roll cage and attach the unit. Then pull the window tightly toward the other side to minimize waviness or wrinkles in the front window and attach it.

8. Now all that is left is to mark the positions of the three snaps on the front of the doors and screw in the snap studs into the Trail Hand. The Bottom of the Doors will hold in place with the Magnets that are sewn into the doors. The rear portion will wrap around and magnets will hold to the frame of the UTV.
   

Cleaning and Storage Recommendations:

1. Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.

2. It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors.  Begin rolling the Cab into a roll approximately 8 inches in diameter.
   Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.

3. A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.

Thank you for your purchase!

Return Policy

If for any reason you choose to return this product it must be returned within 30 days from the date the item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production facility and must be in unused, factory-new condition to receive a refund – a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is  defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20%  restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory-new condition. NOTE: All windshields must be returned with the original protective film intact and not removed. Do NOT REMOVE if you have any intentions of returning the item. Refund/ replacement of a windshield will only be processed on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable  condition (any returned items that have been used, altered or damaged in any way will not be subject to a refund.) All contents including instruction manuals, accessories,  hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, a credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping costs will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.

Warranty

To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or Windshields! Below are the terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops, and/or windshield due to defects of the product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>