DORR DLP-100W LED CONTINUOUS LIGHT Instruction Manual

: June 5, 2024
: DORR

Table of Contents

NOMENCLATURE
**** SAFETY INSTRUCTIONS
PRODUCT DESCRIPTION
NOMENCLATURE
OPERATION
SETTINGS
FURTHER FUNCTIONS
CLEANING AND STORAGE
TECHNICAL DATA
SCOPE OF DELIVERY
DISPOSAL, CE MARKING
SIMPLIFIED EU DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LED CONTINUOUS LIGHT
INSTRUCTION MANUAL
DLP-100W
DLP-100W SET

NOMENCLATURE

DORR DLP-100W LED CONTINUOUS LIGHT - 1

THANK YOU very much for choosing a quality product from DÖRR.
Please read the instruction manual and the safety instructions carefully before using the device for the first time.
Keep this instruction manual together with the device for later use. If other people use this device, provide them with this instruction manual. If you sell the device, the instruction manual is part of the device and must be supplied with it.
DÖRR is not liable for damage caused by improper use or failure to observe the instruction manual and safety instructions.
In the event of damage caused by improper handling or by external influence, the guarantee or warranty becomes void.
Manipulation, structural alteration of the product, as well as the opening of the housing by the user or unauthorized third parties, is considered improper handling.

**** SAFETY INSTRUCTIONS

ATTENTION! The following safety instructions must be observed before use:

This continuous light is to be used exclusively for illumination for photographic purposes. This device is not suitable for permanent room lighting!
Do not look directly into the LEDs and do not point the light beam directly into the eyes of people or animals.
ATTENTION: Looking into the LEDs for a long time can cause irreversible retinal damage in the eye!
Do not use or touch the continuous light with wet hands! Make sure to use it on dry ground.
People with physical or cognitive impairments should only operate the continuous light under guidance and supervision.
Persons with a pacemaker, defibrillator or other electrical implants should keep a minimum distance of 30 cm, as the continuous light generates magnetic fields.
The continuous light is not a toy! Keep the continuous light, accessories, and packing materials away from children and pets to prevent accidents and suffocation.
When folding or unfolding, as well as when aligning the shielding flaps, there is a risk of pinching. Watch your fingers. Attention: The shielding flaps heat up during operation. There is a risk of burns!
Protect the continuous light from rain, moisture, direct sunlight, and extreme temperatures.
Make sure that the continuous light is placed securely and cannot tip over. There is a risk of fire! To avoid tipping off the LED light, align the LED light over a wide tripod leg.
Make sure that your light stand is placed on a level and dry surface.
Only use the continuous light with the mains adapter supplied. Do not use an extension cable. Make sure that no one can trip over the cable connections.
Only connect the continuous light to a socket with a mains voltage of 100-240V.
Only use the continuous light with a special V-Mount Li-Ion battery suitable for this continuous light (optionally available).
Before disconnecting the power or removing the battery (not included), switch off the continuous light at the main switch.
Ensure sufficient ventilation during operation. Never cover
the ventilation slots of the continuous light. There is a risk
of fire!
High voltage can occur in continuous light. If the continuous light is defective or damaged, do not attempt to disassemble or repair it yourself – there is a risk of electric shock! Please contact your specialist dealer.
Protect the continuous light from impacts. Do not use continuous light if it has been dropped. In this case, have the continuous light checked by a qualified electrician before switching it back on.
Keep the continuous light away from easily flammable materials! There is a risk of fire!
Do not place any foils, fabrics, or other unsuitable filters and attachments in front of the LED surface. There is a risk of scorching and fire!
If you notice a scorching smell, switch off the continuous light immediately at the main switch and disconnect the power connection. There is a risk of fire! Please contact your specialist dealer.
Do not use continuous light in the direct vicinity of devices that generate strong electromagnetic fields.
Switch off the continuous light after use and allow it to cool down before touching the housing or the shielding flaps, or before storing the continuous light.
After each use, switch off the continuous light at the main switch and disconnect the power connection.
Protect the continuous light from dirt. Do not clean the continuous light with petrol or harsh cleaning agents. We recommend a lint-free, slightly damp microfibre cloth to
clean the external components of the continuous light. Before cleaning, switch off the continuous light and disconnect the power connection or remove the battery!
Store the continuous light in a dust-free, dry, and cool place.
Please dispose of the device when it is defective or no longer intended for use in accordance with the Waste Electrical and Electronic Equipment Directive WEEE. If you have any questions, please contact the local authorities responsible for disposal.

PRODUCT DESCRIPTION

The DÖRR LED continuous light DLP-100W offers a high luminous intensity of max. 10,000 lux and is continuously dimmable. The color temperature of the long-life LEDs can be variably adjusted from 3,200 K to 5,500 K. The light can be operated with the supplied mains cable or alternatively with a V-Mount Li- Ion battery (optionally available).

100 Watt power
480 bi-color LEDs
Illuminance max. 10,000 lux/1m, continuously dimmable
Color temperature adjustable from 3,200 K to 5,500 K
Outdoor operation possible with V-Mount Li-Ion battery (V-Mount battery optionally available from DÖRR)
Stable, swiveling metal frame for mounting on a light stand (light stands are optionally available from DÖRR)
Diffuser panel included
Regulation by remote control possible (Remote control optionally available from DÖRR)

Accessories supplied only with SET article no. 373513:

Two sturdy light stands max. height 1.80 m
Robust bag with divider

NOMENCLATURE

01 Pivoting screening cover
02 LED luminous surface with a diffuser panel
03 Release button for diffuser panel
04 Locking screws swivel frame
04a) Rubber O-ring black
04b) Washer silver
05 Swivel mount
06 Locking screw lamp stand
07 Tripod light mount
08 Handles
09 Ventilation slots
10 V-Mount battery connection| 11 Release button V-mount battery
12 Battery contacts
13 Colour temperature display
14 Illuminance display
15 Rotary control (blue) for setting colour
temperature/channels
16 Rotary control (white) for setting the
illuminance/groups
17 Main switch (0= Off / I= On)
18 Connection socket “IN” for mains cable
19 Power supply
19a) Connector
19b) Screw lock
---|---

Only with SET article no. 373513:

20 Light tripod
20a) Threaded spigot
20b) Locking screws for 3 pull-outs
20c) Locking screw for tripod legs
20d) Centre struts

OPERATION

Note: Before using it for the first time, carefully remove the protective film from the LED diffuser panel and from the display.
04.1 Mounting the swiveling bracket
To mount the continuous light on the swiveling bracket (05) screw the two locking screws (04) each with the black rubber ring (04a) and the silver washer (04b) as shown in the following sketch:

04.2 Mounting on a light stand
Mount the continuous light on a light stand (optionally available from DÖRR) as described below.
Only with SET article no. 373513:
Pull the tripod legs down until the center struts (20d) are approximately horizontal. Tighten the locking screw (20c).
Slightly loosen the locking screws (20b) to adjust the lampstand with the 3 extensions to the desired height. Tighten the locking screws (20b) again.
Screw the locking screw (06) all the way in and place the light stand holder (07) on the threaded spigot (20a).

ATTENTION: To avoid tilting the LED light, align the light surface of the continuous light over a wide tripod leg.
Tighten the locking screws (06) again.
Loosen the side locking screws (04) on the swiveling bracket (05) to align the continuous light. Tighten the locking screws (04) again.
ATTENTION: To align the continuous light during operation, touch the continuous light only on the two handles (08).

04.3 Removing/attaching the diffuser panel
To remove the diffuser panel, press the release button (03) down and slide the panel out of the guide rails to the right.

DORR DLP-100W LED CONTINUOUS LIGHT - Removing
To refit, the diffuser panel, make sure that the panel is inserted in the upper and lower guide rails. Slide the panel to the left until the release button (03) sticks out completely again. You may have to lift the panel slightly on the left-hand side to be able to push the panel in as far as it will go.

04.4 Operation with power adapter
Make sure that the main switch (17) is in position “0” (= off). Insert the connector (19a) into the socket (18) at the LED light. Pay attention to the pins and holes. Screw tight the screw lock (19b).
IMPORTANT: To disconnect the cable connection, make sure to open the screw lock (19b) first!

Connect the power supply (19) to a socket with a mains voltage of 100-240V.
ATTENTION: Do not use an extension cable. Make sure that no one can trip over the cable connections.

04.5 Operation with V-Mount Li-Ion battery (optional)
ATTENTION: Operate the continuous light only with a special V-Mount Li-Ion battery suitable for the continuous light (optionally available). When inserting the battery, pay attention to the correct polarity (+/-). When not in use for a longer period of time, please remove the battery.
Make sure that the main switch (17) is in position “0” (= off). Push the battery into the V-shaped battery connector (10) from the right until the battery audibly clicks into place. To remove the battery again, make sure that the main switch (17) is in position “0” (= off). Press the unlock button (11). Slide the battery out of the connector to the right.
V-Mount Li-Ion batteries optionally available from DÖRR:
DÖRR Compact V-Mount Li-Ion Battery CVL-98 14.8V, 98Wh
Switch the continuous light on the main switch (17) to position I (=On).

SETTINGS

05.1 Setting the color temperature
To adjust the color temperature in 20 K steps, turn the blue control dial (15):

To the right for cold light with a color temperature of up to max. 5,500 K
To the left for warm light with a color temperature of up to min. 3,200 K

The set value is shown in the display for color temperature (13).

05.2 Setting the illuminance
To adjust the illuminance (brightness), turn the white control dial (16):

To the right for brighter light up to max. 99% (corresponds to 100%)
To the left for darker light up to min. 0%
The set value is shown in the display for illuminance (14).

ATTENTION: After each use, switch off the continuous light at the main switch (17) and disconnect the power connection.

FURTHER FUNCTIONS

06.1 Control via remote control
You have the option of controlling the settings of the DLP-100W LED continuous light via remote control. The corresponding remote control is available separately from DÖRR:
Remote control for DLP-100W/DLP-100W
Article no. 373516

06.1.1 Setting the radio channel on the LED permanent light DLP-70W
Press the control dial (15) to set the color temperature/channels. The permanent light display then shows the set group and next to it the set channel, e.g. A03, instead of the color temperature. To change the channel, turn the control dial until the desired channel appears. Possible channel selection: 00 to 50. After approx. 2 seconds, the display jumps back to the color temperature.

06.1.2 Setting the group on the LED permanent light DLP-70W
Press the rotary control (16) to set the illumination level/groups. The set group, e.g. A, appears on the lamp display instead of the color temperature. To change the group, turn the control dial until the desired group appears. Possible group selection: A, B, C, D, E, and F. After approx. 2 seconds the display jumps back to the color temperature.

For further instructions on use, please refer to the operating instructions for the remote control (click here).

CLEANING AND STORAGE

Do not clean the unit with petrol or harsh cleaning agents. We recommend a lint-free, slightly damp microfibre cloth to clean the outer components of the unit. Before cleaning, switch off the unit and disconnect the power supply or remove the battery. Store the unit in a dust-free, dry, cool place. The unit is not a toy – keep it out of reach of children! Keep the unit away from pets.

TECHNICAL DATA

Number of LEDs	480 Bi-colour
LED frequency	20,000 Hz
Illuminance approx.	10,000 lux/1 m

Only with SET article no. 373513:

LIGHT STAND|
---|---
Height max. approx.| 180 cm
Height min. approx.| 62 cm
Transport dimensions approx.| 56 cm
Pull-outs| 3
Connection| Spigot with 1/4” thread
Material| Aluminum/plastic
Load capacity max. approx.| 5 kg
Weight approx.| 1,230 g
BAG|
Dimensions approx.| 60x33x26 cm
Number of partition walls| 2
Material| Polyester

Dörr GmbH reserves the right to make technical changes without notice.

SCOPE OF DELIVERY

LED continuous light DLP-100W
Article no. 373512
1x LED continuous light
1x Power supply
1x Diffuser filter panel
1x Safety instructions| LED continuous light SET DLP-100W
Article no. 373513
2x LED continuous light
2x Power supply
2x Diffuser filter panel
2x Light tripod
1x Bag
1x Safety instructions
---|---

DISPOSAL, CE MARKING

10.1 BATTERY DISPOSAL
Batteries and rechargeable batteries are marked with the symbol of a crossed- out waste bin. This symbol indicates that empty batteries or rechargeable batteries that can no longer be recharged must not be disposed of in the household waste. Old batteries may contain harmful substances that can cause damage to health and the environment. As the end-user, you are legally obliged to return used batteries (Battery Act §11 Act on the Reorganisation of Waste Product Responsibility for Batteries and Accumulators). You can return batteries free of charge after use at the point of sale or in your immediate vicinity (e.g. at municipal collection points or in shops). You can also return batteries to the seller by post.

10.2 WEEE NOTICE
The WEEE (Waste Electrical and Electronic Equipment) Directive, which came into force as European law on 13 February 2003, led to a comprehensive change in the disposal of discarded electrical equipment. The primary purpose of this directive is to prevent e-waste while promoting reuse, recycling, and other forms of reprocessing in order to reduce waste. The WEEE logo (waste bin) shown on the product and on the packaging indicates that the product must not be disposed of with normal household waste. You
are responsible for delivering all discarded electrical and electronic equipment to appropriate collection points. The separate collection and sensible recycling of e-waste help to use natural resources more sparingly. Furthermore, the recycling of e-waste contributes to preserving our environment and also people’s health. Further information on the disposal of electrical and electronic equipment, recycling, and collection points can be obtained from local authorities, waste disposal companies, specialist retailers, and the manufacturer of the device.

√ 10.3 ROHS CONFORMITY
This product complies with the European RoHS Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment and variations thereof.

10.4 CE MARK
The imprinted CE mark complies with the applicable EU standards and indicates that the device meets the requirements of all EU directives applicable to this product.

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, DÖRR GmbH declares that the radio equipment type [373512, 373513] is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www .doerr-foto.de.