DORR DLP-1000 LED Continuous Light Instruction Manual

DLP-1000 LED Continuous Light
Instruction Manual

Nomenclature

• Only included in kit Item No. 373483!

THANK YOU for choosing this DÖRR quality product.

Please read the instruction manual and safety hints carefully before first use.

Keep this instruction manual together with the device for future use. If other people use this device, make this instruction manual available. This instruction manual is part of the device and must be supplied with the device in case of sale.

DÖRR is not liable for damages caused by improper use or the failure to observe the instruction manual and safety hints.

****SAFETY HINTS

• Do not look directly into the LED and do not direct the light beam into the eyes of humans or animals. CAUTION: Looking into the light for an extended period of time may cause irreversible damage to the retina.
• Only for the illumination for photographic purposes. Not suited for permanent room lightning.
• Protect the device from rain, moisture, direct sunlight, and extreme temperatures.
• Do not operate or touch the device with wet hands.
• Protect the device against impacts. Do not use the device if it has been dropped. In this case, a qualified electrician should inspect the device before you use it again.
• Do not attempt to repair the device by yourself. Risk of electric shock! When service or repair is required, contact qualified service personnel.
• People with physical or cognitive disabilities should use the device with supervision.
• People with cardiac pacemakers, defibrillators, or any other electrical implants should maintain a minimum distance of 30 cm, as the device generates magnetic fields.
• Ensure sufficient ventilation during operation. After use, please switch the device off.
• Make sure to use the device with an appropriate, high-quality Li-Ion battery type NP-F750.
• To avoid deep discharge of the Li-Ion battery when the device is not in use for a longer period, please charge the Li-Ion battery up to approx. 60%.
• Never leave the battery charger unattended while charging the batteries. After charging disconnect the charger from the power supply.
• Only operate with the supplied original power adaptor. Do not use an extension cord.
• Make sure to turn off the device at the main switch before disconnecting from power or removing the battery.
• When unfolding or retracting, as well as when aligning the barn doors there is a risk that your fingers get caught. Watch your fingers.
• To avoid tilting of the LED light, align the light over a widely spread tripod leg. Make sure that the light stand stands on even and dry ground.
• The housing and the barn doors heat up slightly during operation – turn off the LED light after use and allow it to cool down before touching the housing or the barn doors, or before stowing the device in the bag.
• Do not use the device nearby mobile phones and devices that generate strong electromagnetic fields.
• This device is not a toy. To prevent accidents and suffocation keep the device, the accessories, and the packing materials away from children and pets.
• Protect the device against dirt. Never use aggressive cleaning agents or benzine to clean the device. We recommend a soft, slightly damp microfiber cloth to clean the outer parts of the device. Turn off the device and disconnect from the power source or remove batteries before cleaning.
• Store the device in a dust-free, dry, and cool place.
• If the device is defective or without any further use, dispose of the device according to the Waste Electrical and Electronic Equipment Directive WEEE. For further information, please contact your local authorities.

****SAFETY HINTS FOR RECHARGEABLE BATTERIES

Only use high-quality batteries of popular brands. When inserting the battery please respect the correct polarity (+/-). Please remove the battery when the device is not in use for a long period of time. Do not throw the batteries into fire, do not short-circuit, and do not disassemble them. Never charge non-rechargeable batteries – the risk of explosion! Remove leaking batteries from the device immediately. Risk of battery acid burn! Clean the contacts before inserting fresh batteries. In case of contact with battery acid, rinse the affected area immediately with water and contact a doctor. Batteries can be dangerous to life if swallowed. Keep batteries away from small children and pets. Do not dispose of batteries in household waste (see also capture “Disposal of Batteries/Accumulators”).

PRODUCT DESCRIPTION

Continuous LED light kit for photo and video recordings with exciting color and light effects.

• Long-life 3200 K and RGB LEDs
• Color temperature adjustable from 2700 – 9999 K
• Brightness adjustable

NOMENCLATURE

1. Barndoor

2. Locking screws

3. Swivel frame

4. Battery slot
   4a) Battery contact pins

5. LCD display

6. Menu button

7. HUE/Saturation button

8. CCT button

9. Main switch
   (a position I = operation with battery/position II=operation with power adapter)

10. Socket for power adapter

11. Control dial/press button

12. Socket for light stand with spigot
    12a) Locking screw

13. Power adapter
    13a) Power cable socket
    13b) Connection plug
    13c) Screw lock
    13d) Power cable
    Only included in kit Item No. 373483

14. Battery charger
    14a) LED charging indicator
    14b) Battery contact pins +/
    14c) Battery slot
    14d) Socket for power cable
    14e) Power cable

15. Li-Ion battery
    15a) Battery contacts +/-

FIRST COMMISSIONING

**CAUTION
Before connecting or disconnecting cable connections, make sure that the main switch (9) is on position O = Off.**

Insert the connection plug (13b) into the socket (10) at the LED light. Pay attention to the pins and holes. Screw tight the screw lock (13c). To disconnect the cable connection,  make sure to open the screw lock (13c) first!
Plug the power cable (13d) into the power cable socket (13a) and connect the power supply to a socket outlet.

Switch on the LED light at the main switch (9):
position II = On (operation with power adapter).

CAUTION
After each use please turn off the LED light (main switch 9 = position O = Off).

LED DISPLAY/SETTINGS

Switch on the LED light at the main switch (9):
position II = On (operation with power adapter) or position I = On (operation with batteries – refer to chapter 08).

MENU HUE/SATURATION

Here you can set the desired color, saturation, and intensity. Press the HUE button (7). The LCD display shows  the following overview:

Battery capacity indicator
Hue (color)
Sat (saturation)
Int (intensity)
R:/G:/B:/W: (values)

Input field Hue = select color

Turn the control dial (11) to the desired color.

Press the HUE button (7) to confirm your selection and to enter the next input field.

Input field Sat = select saturation

Turn the control dial (11) to the desired saturation. Setting from 0% – 100%. Press the control dial (11) to confirm your selection and to enter the next input field “Intensity”.

Input field Int = select intensity
Turn the control dial (11) to the desired intensity. Setting from 0% – 100%.

PRE-SETTINGS (HUE/SATURATION)

First press the HUE button (7) and then the menu button (6). Turn the control dial (11) to select the desired menu point. Press the control dial (11) to enter the input fields.

RGBW dimming

Here you can select the desired red, green, blue, and white values. Turn the control dial (11) to select the desired value.
Press the control dial (11) to confirm your selection and to enter the next input field.

R Red: 0-255 G Green: 0-255 B Blue: 0-255 W White: 0-255

Press the menu button (6) to return to the overview.

Pre-set Colours

Here you have the possibility to save your 8 most used colors

Before you open this menu point, first select the color of the LED light as described in chapter 06.1. Then press the menu button (6). Turn the control dial (11) until the menu point “Preset Colors” is highlighted. Press the control dial (11).  Turn the control dial (11) to select a memory location number from 1 – 8. Press the control dial (11) to confirm your selection and to save the selected color. Press the menu button (6) twice to return to the overview.

Pre-set Cycle Effects

Here you can choose between 35 pre-set light and cycle effects. Turn the control dial (11) to browse through the various pre-settings (mode: 37-106). Press the control dial (11) to confirm your selection and to enter the next input field  “Speed”. Here you can adjust the playback speed of the selected cycle effect.

Speed adjustment: from 1 = fast playback to 32 = slow playback.

Press the menu button (6) twice to return to the overview

Pre-set Cycle Effects

MENU CCT

Here you can set the desired color temperature, green-magenta correction, and brightness. Press the CCT button (8).  The LCD display shows the following overview:

Battery capacity indicator
CCT (color temperature)
GN (green-magenta correction)
BRT (brightness)
R:/G:/B:/W: (values)

Input field CCT = select colour temperature

Turn the control dial (11) to the desired color temperature. Setting from 2700 K – 9999 K. Press the CCT button (8) to confirm your selection and to enter the next input field.

2 Input field GN = green-magenta correction

Turn the control dial (11) to the desired value. Setting from 0 – 255. Press the control dial (11) to confirm your selection and to enter the next input field “Brightness”.

Input field BRT = select brightness

Turn the control dial (11) to the desired brightness. Setting from 0% – 100%.

PRE-SETTINGS (CCT)

First press the CCT button (8) and then the menu button (6). Turn the control dial (11) to select the desired menu point. Press the control dial (11) to enter the input fields.

RGBW dimming

Here you can select the desired red, green, blue and white values. Turn the control dial (11) to select the desired value. Press the control dial (11) to confirm your selection and to enter the next input field.

R Red: 0-255 G Green: 0-255 B Blue: 0-255 W White: 0-255

Press the menu button (6) to return to the overview

Pre-set Colour Temperatures

Here you have the possibility to save your 8 most used color temperatures

Before you open this menu point, first select the color temperature at the LED
light as described in chapter 07.1. Then press the menu button (6). Turn the control dial (11) until the menu point “Preset Temp” is highlighted. Press the control dial (11).
Turn the control dial (11) to select a memory location number from 1 – 8. Press the control dial (11) to confirm your selection and to save the selected color temperature. Press the menu button (6) twice to return to the overview.

Pre-set Light Source

Here you can choose between 10 pre-set light sources. Turn the control dial (11) to browse through the various pre-settings. Press the control dial (11) to confirm your selection. Press the menu button (6) twice to return to the overview.

Pre-set Light Source

The following functions only for kit Item No. 373483:

OPERATION WITH LITHIUM-ION BATTERIES

CHARGING THE LI-ION BATTERIES
Before the first operation with batteries, please fully charge the Li-Ion batteries (15) with the supplied battery chargers (14).

CAUTION
Only charge rechargeable Li-Ion batteries of the type NP-F750 with the supplied battery charger! The charger is not suited to charge other battery types!

Insert the power cable (14e) to the cable socket of the battery charger (14d) and connect to an electrical outlet. The LED charging indicator (14a) lights up green.

Place the Li-Ion battery (15) over the center of the charging slot (14c) and pay attention to the correct polarity (markings +/- on the battery and in the charging slot).
Slide the battery fully forward until it touches the battery contact pins (14b). If the battery is inserted properly and the charging process has started, the LED charging indicator
(14a) lights up red. When the battery is fully charged, the LED charging indicator  (14a) turns green. Slide the Li-Ion battery backward and remove it from the charging slot. Disconnect the battery charger from the electrical outlet.

CAUTION
Never leave the battery charger unattended while charging the battery. After charging, disconnect the charger from the power supply.

NOTE
To avoid deep discharge of the Li-Ion batteries when DLP-1000 light is not in use for a longer period, please charge Li-Ion batteries up to approx. 60%.

INSERTING THE LI-ION BATTERIES

CAUTION
Before inserting or removing the Li-Ion batteries, make sure that the LED light is turned off (main switch (9) to position O = Off).

Insert the Li-Ion batteries (15) into the battery slots (4) with the battery contacts (15a) facing to the battery contact pins (4a). Slide the battery fully forward until it touches the battery contact pins (4a).

Switch on the LED light at the main switch (9):
the position I = On (operation with batteries).

After use turn off the LED light at the main switch (9, position O=Off) and disconnect from the power source. Please remove batteries when the LED light is not in use for a longer period.
To remove the Li-Ion batteries, slide the batteries backward and remove them out

CLEANING AND STORAGE

Never use aggressive cleaning agents or benzine to clean the device. We recommend a soft, slightly damp microfiber cloth to clean the outer parts of the device.
Turn off the device and disconnect from the power source or remove batteries before cleaning. Store the device in a dust-free, dry, and cool place. This device is not a toy – keep it out of reach of children.Keep away from pets.

TECHNICAL SPECIFICATIONS

150 mA (max.)
Output| DC 8,4 V/600 mA
Dimensions| approx. 8,5 x 4,6 x 4 cm
Weight| approx. 118 g
Battery| (Replace-) Sony NP-F750 Li-Ion battery 7,2 V
4400 mAh (≙ 31,68 Wh)
Light stand max. height| approx. 215 cm

SCOPE OF DELIVERY

Item No. 373485 LED continuous light DLP-1000 RGB single:
1x LED continuous light DLP-1000
1x Power adapter
1x Safety hints

Item No. 373483 LED continuous light DLP-1000 RGB kit:
2x LED continuous light DLP-1000
2x Power adapter
2x Light stand
4x Li-Ion battery NP-F750
4x Battery charger
1x Bag
1x Safety hints

DISPOSAL, CE MARKING

DISPOSAL OF BATTERIES/ACCUMULATORS
Batteries are marked with the symbol of a crossed-out bin. This symbol indicates that empty batteries or accumulators which can no longer be charged should not be disposed of with household waste. Waste batteries may contain harmful substances that can cause damage to health and to the environment. Please use the return and collection systems available in your country for the disposal of waste batteries.

WEEE INFORMATION

The Waste Electrical and Electronic Equipment Directive (WEEE Directive) is the European Community directive on waste electrical and electronic equipment, which became  European law in February 2003. The main purpose of this directive is to prevent electronic waste. Recycling and other forms of waste recovery should be encouraged to reduce waste. The symbol (trash can) on the product and on the packing means that used electrical and electronic products should not be disposed of with general household waste. It is your responsibility to dispose of all your electronic or electrical waste at designated collection points. Disposing of this product correctly will help to save valuable resources and it is a significant contribution to protecting our environment as well as human health. For more information about the correct disposal of electrical and electronic equipment,  recycling, and collection points please contact your local authorities, waste management companies, your retailer, or the manufacturer of this device.

ROHS CONFORMITY
This product is compliant with the European RoHS directive for the restriction of the use of certain hazardous substances in electrical and electronic equipment and its amendments.

ROHS CONFORMITY
This product is compliant with the European RoHS directive for the restriction of the use of certain hazardous substances in electrical and electronic equipment and its amendments.

CE MARKING
The CE marking complies with the European standards and indicates that the product meets the requirements of the applicable EU directives.

DÖRR LED DAUERLICHT DLP-1000 RGB/
LED DAUERLICHT DLP-1000 RGB SET
Artikel Nr 373485/373483
DÖRR GmbH Messerschmittstr. 1 · D-89231 Neu-Ulm · Fon +49 731.970 37 69 · info@doerr.gmbh · doerr-foto.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>