DORR SVL-112 Pro Slim Led Video Light Instruction Manual
- June 5, 2024
- DORR
Table of Contents
SVL-112 Pro Slim Led Video Light
Instruction Manual
NOMENCLATURE
THANK YOU for choosing this DÖRR quality product.
Please read the instruction manual and safety hints carefully before first
use.
Keep this instruction manual together with the device for future use. If other
people use this device, make this instruction manual available. This
instruction manual is part of the device and must be supplied with the device
in case of sale.
DÖRR is not liable for damages caused by improper use or the failure to
observe the instruction manual and safety hints.
SAFETY HINTS
-
Do not look directly into the LED and do not direct the light beam into the eyes of humans or animals.
CAUTION: Looking into the light for an extended period of time may cause irreversible damage to the retina. -
Only for the illumination for photographic purposes. Not suited for permanent room lightning.
-
During the operation, the aluminum housing and the LEDs will warm up.
-
Protect the device from rain, moisture, direct sunlight, and extreme temperatures.
-
Never leave the light unattended while charging the battery. After charging, disconnect the light from the power supply.
-
Turn off the light after use.
-
Do not submerge or throw the light into the water. Do not throw the light into fire – risk of explosion!
-
If the device is not in use for a long period of time, we recommend charging the battery to about 60%. The storage of an empty or fully charged battery will shorten its life.
-
The built-in battery and the LEDs cannot be replaced.
-
Do not operate or touch the device with wet hands.
-
Protect the device against impacts. Do not use the device if it has been dropped. In this case, a qualified electrician should inspect the device before you use it again.
-
Do not attempt to repair the device by yourself. Risk of electric shock! When service or repair is required, contact qualified service personnel.
-
People with physical or cognitive disabilities should use the device with supervision.
-
People with cardiac pacemakers, defibrillators, or any other electrical implants should maintain a minimum distance of 30 cm, as the device generates magnetic fields.
-
This device is not a toy. To prevent accidents and suffocation keep the device, the accessories, and the packing materials away from children and pets.
-
Protect the device against dirt. Never use aggressive cleaning agents or benzine to clean the device. We recommend a soft, slightly damp microfiber cloth to clean the outer parts of the device. Before cleaning make sure to switch off the device and take off the USB power supply!
-
Store the device in a dust-free, dry, and cool place.
-
If the device is defective or without any further use, dispose of the device according to the Waste Electrical and Electronic Equipment Directive WEEE. For further information, please contact your local authorities.
PRODUCT DESCRIPTION
- Ultra-flat LED continuous light for photo and video recordings
- For DSLR, DSLM & camcorder with hot shoe mount
- Brightness dimmable in 5% steps
- High-grade aluminum housing, with a clear structured LED display
- Supplied with a universal flash shoe with ¼” tripod socket, USB-C charging cable, diffusor plate, honeycomb, a storage pouch
NOMENCLATURE
-
¼“ Connection thread
-
LCD display
-
On/Off/Menu button
-
Toggle switch +/- for adjustments
-
USB-C „5V in“ charging socket
-
LED surface
-
Diffusor plate
07a) Holder for diffusor plate -
Honeycomb
-
USB-C charging cable
-
Universal flash hot shoe
10a) Locking screw -
Storage pouch
FIRST STEPS
CAUTION: Before the first use please tear off the protective film from the
LED surface (06)!
Charging the internal Li-Polymer battery
Before first use, please fully charge the built-in Li-Po battery. Connect the
USB-C charging cable (09) with the USB-C „5V in“ charging socket (05) of the
video light. While charging you will see the actual charging status on the LCD
display (02):
After charging, remove the USB-C charging cable (09) from the video light and
the USB charging source. When the battery is totally empty, the charging time
of my PC is about 2 ½ hours.
NOTE: If the LED video light is not in use for a long period of time, we
recommend charging the battery to about 60% to avoid deep discharge of the
battery.
OPERATION
Press the On/Off/Menu button (03) for about 3 seconds in order to turn
on the LED video light.
Press the On/Off/Menu button (03) shortly to switch from brightness to
color temperature and back. The arrow ▷ shows the selected menu point
in the display (02):
The toggle switch for adjustments (04) increases brightness and color
temperature when moved upwards (+).
The toggle switch for adjustments (04) decreases brightness and color
temperature when moved downwards (-).
Brightness is adjustable in 5% steps, while the color temperature is
adjusted in 100° Kelvin steps.
During operation, the display (02) shows the remaining battery power in h
(hours) or m (minutes).
The battery symbol shows the battery capacity graphically.
Press the On/Off/Menu button (03) for about 3 seconds in order to turn
off the video light.
CAUTION:
- During operation, the housing and LEDs will warm up.
- Turn off the device after usage by using the On/Off/Menu button (03).
- Let the device cool down completely, before placing it in the storage pouch.
MOUNTING
06.1 Mounting on a camera/camcorder with flash hot shoe
Screw the universal flash hot shoe (10) into the ¼” connection thread (01) of
the video light. Slide the universal flash hot shoe (10) into the hot shoe
mount of your camera or your camcorder. Tighten the locking screw (10a).
06.2 Mounting/unmounting the diffusor plate
The white diffuser plate (07) provides soft light and reduces harsh shadows.
Place the diffusor plate (07) onto the LED panel on the front side of the
video light. Press all 4 corners gently until the 4 holders for the diffusor
plate (07a) snap in the notches of the video light. In order to remove the
diffusor plate (07) loosen the 4 holders of the diffusor plate (07a) first.
06.3 Mounting/unmounting the honeycomb
The honeycomb (08) directs the light and reduces stray light, while contrast
and brilliance are intensified. The illumination becomes harder. The white
diffuser plate (07) must be removed before the honeycomb (08) is installed.
Slide the honeycomb (08) from the side onto the video light. Slide it back to
the side to remove it.
CLEANING AND STORAGE
Never use aggressive cleaning agents or benzine to clean the device. We recommend a soft, slightly damp microfiber cloth to clean the outer parts of the device. Before cleaning make sure to switch off the device and take off the USB power supply! Store the device in a dust-free, dry, and cool place. This device is not a toy – keep it out of reach of children. Keep away from pets.
TECHNICAL SPECIFICATIONS
| Number of LEDs | 112 |
|---|---|
| LED Power max. | 9 W |
| Color temperature | 3200-5600 K (± 300 K) |
| Illumination power approx. | 800 Lux/1m |
| Dimmer | 5 – 100% |
| Colour Rendering Index (CRI) | > 96 Ra |
| Power supply | 3.85 V, 2470 mAh Built-in Lithium Polymer battery |
| Runtime at full power approx. (with a fully charged battery) | 1,5 hours |
| Charging current | 5V 1A / 5V 2A |
| Port | USB-C |
| Dimensions approx. | 12,5 x 7 x 1 cm |
| Weight approx. | 130 g |
Dörr GmbH reserves the right to make technical changes without notice.
CONTENT
- 1x SLIM LED Video Light SVL-112 PRO
- 1x Universal flash hot shoe
- 1x USB-C charging cable
- 1x Diffusor plate white
- 1x Honeycomb
- 1x Storage pouch
- 1x Safety hints
DISPOSAL, CE MARKING
10.1 DISPOSAL OF BATTERIES/ACCUMULATORS
Batteries are marked with the symbol of a crossed-out bin. This symbol
indicates that empty batteries or accumulators which can no longer be charged
should not be disposed of with household waste. Waste batteries may contain
harmful substances that can cause damage to health and to the environment.
Please use the return and collection systems available in your country for the
disposal of waste batteries.
10.2 WEEE INFORMATION
The Waste Electrical and Electronic Equipment Directive (WEEE Directive) is
the European Community directive on waste electrical and electronic equipment,
which became European law in February 2003. The main purpose of this directive
is to prevent electronic waste. Recycling and other forms of waste recovery
should be encouraged to reduce waste. The symbol (trash can) on the product
and on the packing means that used electrical and electronic products should
not be disposed of with general household waste. It is your responsibility to
dispose of all your electronic or electrical waste at designated collection
points. Disposing of this product correctly will help to save valuable
resources and it is a significant contribution to protecting our environment
as well as human health. For more information about the correct disposal of
electrical and electronic equipment, recycling, and collection points please
contact your local authorities, waste management companies, your retailer, or
the manufacturer of this device.
10.3 ROHS CONFORMITY
This product is compliant with the European RoHS directive for the restriction
of the use of certain hazardous substances in electrical and electronic
equipment and its amendments.
10.4 CE MARKING
The CE marking complies with the European standards and indicates that the
product meets the requirements of the applicable EU directives.
DÖRR GmbH
Messerschmittstr. 1 · D-89231 Neu-Ulm
Fon: +49 731 970 37 69
[email protected]
https://doerr-foto.de
Slim LED Videolicht SVL-112 PRO
Artikel Nr 371083
Made in China