INVENTUM KV1615W Combi Refrigerator Freezer Instruction Manual

INVENTUM KV1615W Combi Refrigerator Freezer

Reversing the door openings

Tools you will need

The doors of the appliance can be opened on the right or left side. In order to reverse the door openings, please observe the instructions below. It would be best to do this with two people.
Attention: switch off the thermostat and remove the plug from the socket. Remove all items from the refrigerator, including the shelves and drawers, before reversing the door opening.

1. Use a putty knife or thin-blade screwdriver to remove the screw hole cap (left) a, then remove the upper hinge cover (right) b.

2. Unscrew the special self-tapping screws and remove the upper hinge.
   Remark: During this step, hold the upper door with your hand to prevent it from falling.

3. Remove the upper hinge axis, transfer it to the reversed side and tighten it securely. Put it down for late use.

4. Remove the upper door from the middle hinge by carefully lifting the door straight up.
   Remark: when removing the door, watch for the washer(s) between the center hinge and the bottom of the upper door that may stick to the door. Do not lose.

5. Place the upper door on a smooth surface with its panel upwards. Loosen screw a and remove the stop block b.

6. Install these 2 parts a and b to the left side and tighten securely.

7. Unscrew the two special self-tapping screws which are used for fixing the middle hinge part, then remove the middle hinge part that holds the lower door in place.
   Remark: when removing the door, watch for the washer(s) between the center hinge and the bottom of the upper door that may stick to the door. Do not lose.

8. Place the lower door on a smooth surface with its panel upwards. Loosen screw a and remove the stop block b.

9. Install these 2 parts a and b to the left side and tighten securely.

10. Change the screw hole caps on the middle cover plate from the left to the right (as shown in the figure).

11. Lay the refrigerator backward on soft foam packaging or similar material to prevent damage. Remove both adjustable bottom feet b, and remove the lower hinge c by unscrewing the special self-tapping screws a.

12. Replace the adjustable bottom feet with the other side of the hinge and fixate them.

13. Replace the lower hinge to the left side and fixate it with the special self-tapping screws. Carefully place the refrigerator upright.

14.  Place the lower door on the bottom hinge and support it. Make sure the door is aligned. Flip over the middle hinge 180 degrees and fix it on the other side of the appliance. Place the middle hinge axis into the upper hole of the lower door and tighten the screws b of the hinge.

15. Place the upper door on the middle hinge. Make sure the door is aligned.

16. Place the upper hinge a. Make sure the upper hinge axis fits in the upper hole of the upper door. Remark: please support the upper door with your hand when doing this. Fixate the upper hinge with the self-tapping screws.

17. Place the screw hole cap a and place the other hinge cover b (which is in the plastic bag). Place the shelves and drawers back in the refrigerator. Allow the appliance to rest for 2 to 3 hours before inserting the plug into the socket.

safety instructions

• Please read these instructions before operating the appliance and retain it for future use.
• Only use this appliance for the purposes described in the instruction. The appliance is suitable for storing food. It is possible to freeze fresh food in the freezer section.
• Only connect the appliance to alternate current, to an earthed wall socket, with a mains voltage that corresponds with the information provided on the information plate of the appliance.
• Do not use single/multiple adapters or extension cords.
• Do not use the appliance if the plug, cord, or appliance is damaged, if the appliance no longer functions properly or if it is damaged in any other way. If this is the case, consult the shop or our technical service. Never replace the plug or cord yourself.
• The appliance must be moved and installed by two or more persons.
• Be careful when moving the appliance to prevent the floor from getting damaged.
• During installation, do make sure the power cable is not damaged.
• Check that the appliance is not placed too close to a heat source.
• In order to ensure proper ventilation, a free space of 10 cm should be maintained around the appliance and 30 cm from the top.
• Do not place anything on top of the appliance, such as an oven or microwave.
• Never cover the ventilation openings.
• Make sure the cooling pipes do not get damaged.
• Install the appliance on a sturdy, flat, and stable surface. temperature falls within the applicable class, depending on the climate class found on the information plate on the back of the appliance.

Install the appliance in a dry and well-ventilated room. The appliance is intended for use in a room where the ambient Climatic class

• Do not store explosive or highly flammable substances in the appliance. The vapors could cause a fire hazard or an
• Do not store glass bottles or jars with liquids in the freezer, as they could break when
• Do not use mechanical, electrical, or chemical agents to speed up the defrosting
• Make sure that children are unable to play with the appliance, such as hide in This is dangerous.
• Keep the appliance out of reach of children. Children do not see the dangers when handling electrical, Therefore, never allow children to work with electrical appliances without supervision. Keep the appliance and cord out of reach of children younger than 8 years of age.

Note: Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.

• The appliance can be used by children of 8 years and older and persons with a limited physical, sensory or mental capacity or lack of experience or knowledge, provided they use the appliance under supervision or have been instructed about its safe use and understand the hazards
• The appliance may not be cleaned or maintained by children unless this is done under
• Repairs to electrical appliances should only be performed by skilled It is dangerous to perform a repair whereby the base unit of the appliance must be opened.
• Only use and store the appliance
• Never bend the power cord sharply or allow it to run across hot parts.
• Always remove the plug from the socket when the appliance must be cleaned or
• Never use the appliance with parts that are not recommended or supplied by the
• Do not pull the cord and/or appliance to remove the plug from the wall Never touch the plug with wet or moist hands.
• Be careful with ice cubes and ice If these are consumed directly out of the freezer, there is a risk of frostbite.
• Never submerge the appliance, cord, or plug in

The appliance cannot be used with a timer or separate remote control

• This appliance is only suitable for households If the appliance is not used as intended, no compensation can be claimed in case of defects or accidents and the warranty will be invalidated.

If you decide not to use the appliance anymore due to a defect, we recommend cutting off the cord after removing the plug from the wall socket. Household appliances are not normal waste. Take the appliance to the waste processing department concerned in your municipality

Refrigerant

The refrigerant isobutene (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable. During transportation and installation of the appliance, ensure that none of the components of the refrigerant circuit becomes damaged. The refrigerant (R600a) is flammable.
WARNING: Refrigerators contain refrigerant and gases in the insulation. Refrigerants and gases must be disposed of professionally as they may cause eye injuries or ignition. Ensure that tubing of the refrigerant circuit is not damaged prior to proper disposal.

WARNING: Risk of fire/ flammable materials

If the refrigerant circuit should be damaged:

• Avoid open flames and sources of ignition.
• Thoroughly ventilate the room in which the appliance is situated.

It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short circuit, fire, and/or electric shock.

appliance description

1. Thermostat with internal lighting
2. Glass shelves
3. Crisp drawer
4. Freezer drawers
5. Adjustable feet
6. Door – freezer section
7.  Bottle compartment
8. Door compartments
9. Door – cooler section
10. Egg tray

Before the first use

Before using the appliance for the first time, you should proceed as follows: carefully unpack the appliance and remove all packaging material and any promotional stickers. Keep the packaging (plastic bags, polystyrene, and cardboard) out of the reach of children. After unpacking the appliance, check it for external damage that may have occurred during transport. Place the appliance on a sturdy, flat surface and make sure there is enough space all around for sufficient ventilation. A minimum space of 10 cm is required between the appliance and the surrounding walls to keep 30 cm clear above the appliance. In this way, the appliance is able to release heat properly, cool well, and function in an energy-efficient way. You can use the adjustable feet to level the appliance. Do not place the appliance near heat sources such as central heating or a stove. Do take note of the climate class of the appliance. When placed in a room that is too cold, the refrigerator will not function properly. After placing the appliance, leave it for at least 3 hours before inserting the plug into the socket. First, clean the interior of the appliance. Use warm soapy water with, for instance, washing-up liquid, all- purpose cleaner, or soda. Wipe the inside of the appliance after cleaning with clean water and properly wipe everything dry. Leave the appliance to dry for 1 to 2 hours.

Usage

The control unit of the appliance is located on the inside. Check that the thermostat is off in position 0. Check that the voltage corresponds with what is stated on the information plate and insert the plug into the socket.

Adjusting the temperature
By means of the thermostat, you are able to change the temperature in the refrigerator. The possible positions of the thermostat: Switch off appliance – position 0Maximum temperature – position 1 (least cold) Optimum temperature – positions 2-5 Minimum temperature – position 7 (coldest) Set the temperature with the thermostat and select a position between 1 and 7. We recommend setting the appliance to position 4. The appliance will now cool continuously until the set temperature has been reached. Allow the appliance to reach the required temperature with no food. Usually, this will take 2 to 3 hours. After that, you can set the thermostat to the required position and fill the appliance with food. Only use highest position 7 for making ice cubes, or at the beginning when placing new frozen products in the freezer section.

The internal temperature of the refrigerator
Adjusting the temperature to the changing seasons is not recommended. The increase in ambient temperature is detected by the sensor and the compressor will automatically work longer to maintain the required internal temperature.

Minor changes in temperature
Minor changes in temperature are normal and can be caused by storing a large number of fresh products in the freezer, or by leaving the door open for a longer period of time. The food is not affected, and the temperature quickly returns to the normal value.
Set the thermostat to position 0 to switch off the appliance.

Attention:
The ambient temperature, the frequency of opening the door, and the position of the appliance have an effect on the temperature in the appliance. Take this into account when setting the thermostat.

• Do not place hot food in the appliance.
• You should never place hazardous, highly flammable, or explosive substances such as alcohol, acetone, or petrol in the appliance because there will be a hazard of explosion.
• Carefully package meat and fish to prevent unpleasant smells.
• Leave sufficient space between the different foods, to allow the air to circulate properly.
• Do not place food against the rear wall of the appliance. The shelves have a stopper to prevent this.
• Do not leave the door open for longer than necessary.

tips

• High ambient temperatures have a negative effect on energy use. Keep the appliance in a position away from direct sunlight or other sources of heat.
• Keep ventilation openings free. Clogged openings lead to higher use of energy.
• Try not to open the door too often, especially when the weather is wet and hot. Once you open the door, mind to close it as soon as possible.
• The space between the shelves and the rear wall of the refrigerator compartment must be unobstructed to allow the cool air to circulate. Therefore don’t place any food items against the back.
• Turn the thermostat to a lower setting when the circumstances allow it.
• Before storing freshly cooked food, make sure the food has cooled at least to room temperature.
• Ice and frost layer increase energy consumption, so clean the appliance as soon as the layer is 3 to 5 mm thick.
• If the gasket is damaged or if it turns out that the sealing is poor, the energy consumption is substantially higher. To restore efficiency, replace the gasket.
• Always consider the instructions, otherwise the energy consumption is substantially higher.

To avoid contamination of food, please respect the following instructions

• Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
• Clean regular surfaces that can come in contact with food and accessible drainage systems.
• Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
• Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice cream, and making ice cubes.
• One-, two- and three-start compartments are not suitable for the freezing of fresh food.

dairy products, cakes, drinks and other foods are not suitable for freezing.
2| (*)-Freezer| ≤-18| Seafood (fish, shrimp, shellfish), freshwater aquatic products and meat products (recommended for 3 months, the longer the storage time, the worse the taste and nutrition), suitable for frozen fresh food.
3| -Freezer| ≤-18| Seafood (fish, shrimp, shellfish), freshwater aquatic products and meat products (recommended for 3 months, the longer the storage time, the worse the taste and nutrition), suitable for frozen fresh food.
4| *-Freezer| ≤-12| Seafood (fish, shrimp, shellfish), freshwater aquatic products and meat products (recommended for 3 months, the longer the storage time, the worse the taste and nutrition), suitable for frozen fresh food.
5| -Freezer| ≤-6| Seafood (fish, shrimp, shellfish), freshwater aquatic products and meat products (recommended for 3 months, the longer the storage time, the worse the taste and nutrition), suitable for frozen fresh food.
6| 0-star| -6 ~ 0| Fresh pork, beef, fish, chicken, some packaged processed foods, etc. (Recommended to eat within the same day, preferably no more than 3 days).

Partially encapsulated processed foods (non-freezable foods).

7| Chill| -2 ~ +3| Fresh/ frozen pork, beef, chicken, freshwater aquatic products, etc. (7 days below 0°C and above 0°C is recommended for consumption within that day, preferably no more than 2 days). Seafood (less than 0 for 15 days, it is not recommended to store above 0°C.
8| Fresh food| 0 ~ +4| Fresh pork, beef, fish, chicken, cooked food, etc. (Recommended to eat within the same day, preferably no more than 3 days)
9| Wine| +5 ~ +20| Red wine, white wine, sparkling wine, etc.

Note: please store different foods according to the compartments or target storage temperature of your purchased products.

• If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould from developing within the appliance. Water dispenser cleaning (special for water dispenser products):
• Clean water tanks if they have not been used for 48 h; flush the water system connected to a water supply if water has not been drawn for 5 days.

WARNING:

Food needs to be packed in bags before putting into the refrigerator, and liquids need to be packed in bottles or  capped containers to avoid the problem that the product design structure is not easy to clean

cleaning & maintenance

Before cleaning the appliance, switch the appliance off by setting the thermostat to 0 and remove the plug from the socket. The cooler section of the refrigerator defrosts automatically. Defrost the appliance when the layer of ice in the freezer section has reached a thickness of 3 to 5 mm. Use this opportunity to clean the appliance. When there is white frost on the rear wall of the cooler section, it will defrost automatically. The defrost water runs downwards and is discharged via the defrost water drain. The opening of the defrost water drain can become clogged. Clean the opening by means of the skewer. For areas that are difficult to clean in the refrigerator, such as narrow gaps or corners, it is recommended to wipe them regularly with a soft rag, soft brush, etc. When necessary use some auxiliary tools, such as thin sticks (toothpicks), to ensure no contamination can accumulate in these areas. Clean the outside of the refrigerator and the door gasket with mild soap and water. Use a soft moist cloth. We recommend that you dust the back of the appliance and on the floor with a cloth or vacuum cleaner once a year in order to maintain a good output and low energy consumption. Do not use hard brushes, cleaning steel wire balls, wire brushes, abrasives, such as toothpaste, organic solvents (such as alcohol, acetone, oils, etc.), boiling water, acid or alkaline items to clean the refrigerator considering that this may damage the fridge surface and interior. Boiling water and benzene may deform or damage plastic parts.

DEFROSTING AND CLEANING THE REFRIGERATOR

• Switch off the thermostat [0] and remove the plug from the socket.

• Open the door and remove the products. Store the products in a cool location, packed in newspapers and blankets.

• Leave the door open, this will accelerate the defrosting process.

• Place a receptacle under the freezer section and wait for the ice to defrost. You can also place a dish with hot water (not boiling) in the freezer section.
  Remove loose ice using a plastic scraper.
  Warning Never remove ice with sharp objects, defrosting sprays, a hair dryer, a heater, or something similar. This could lead to unsafe situations and cause irreparable damage to the appliance.

• Clean the interior of the appliance. Use warm soapy water with, for instance, washing-up liquid, all-purpose cleaner, or soda in order to prevent nasty smells. Wipe the inside of the appliance after cleaning with clean water and properly wipe everything dry.

• Leave the appliance to dry for 1 to 2 hours. The shelves and drawers can be removed from the appliance easily and washed by hand. These components may never be cleaned in the dishwasher.

• Clean the outside of the appliance and the door rubbers with a soft damp cloth.

• Switch on the appliance in accordance with the user’s instructions.

INSTRUCTIONS

• A large amount of ice on the freezer surfaces disrupts the operation of the appliance and increases energy consumption.
• Defrost the appliance at least once or twice per year. When too much ice is formed, you must defrost the appliance more often.
• Place the frozen products in a large tray, wrapped in newspapers and a blanket, and store them in a cool location.
• Defrosting the refrigerator should be done as quickly as possible. Storing the products at room temperature for a time period that is too long reduces their shelf life.

REPLACING THE LED LAMP
This appliance has been provided with a LED lamp. This lamp lasts for a longer period of time. When the LED lamp in the appliance is broken, you are not able to replace it yourself. Contact the Inventum service department.

troubleshooting

– check that the plug is properly inserted in the socket

– check that the power cable is not damaged

– check that there is voltage on the socket by connecting a different appliance, such as a night lamp

– check that the appliance is on by setting the thermostat

higher than 0

The interior lighting does not work.| The lamp is defective or the plug is not in the socket.| Check the solutions above or have the lamp replaced.

Temperature in the refrigerator is too high or too low

| Wrong setting of the thermostat.| – turn the thermostat to a different position
The ambient temperature is higher or lower than the temperature indicated in the table with technical data.| The appliance is intended for operation in an

ambient temperature indicated in the table with technical data supplied with the appliance.

The appliance is located in direct sunlight or near a heat source.| Change the location of the appliance according to the information in the instruction manual.
A too large amount of hot food has been placed in the appliance at once.| Wait 72 hours until the products are frozen. The temperature in the appliance will return to the required level.
The ventilation at the rear of the appliance is hindered.| Keep the appliance 10 cm away from the walls, for sufficient ventilation.
The door of the refrigerator is opened too frequently or remains open for too long.| Open the door less often and/or reduce the time that the door remains open.
The door is not closed properly.| Make sure the foods are placed in such a way that they do not hinder the door when it is being closed.
The compressor does not work often enough.| Check that the ambient temperature is not lower than the range of the climate class.
The door rubber is loose.| Fasten the door rubber or have it replaced.
The appliance is working continuously.| Wrong setting of the thermostat.| – turn the thermostat to a higher position
There is water in the lower section of the refrigerator.| The opening of the defrost water drain is clogged.| Clean the opening of the defrost water drain by means of the skewer.
The ventilation within the cooler section is hindered.| Check that the food does not make contact with the rear wall of the refrigerator.

Unusual or loud noises

| The appliance is not level and stable.| Level the appliance with the adjustable feet.
The appliance is standing against something.| Place the appliance in such a way that it is not standing against anything.

During normal use of the cooling appliance, different types of noises can occur that do not have any effect on the correct operation of the freezer.
Noises that can be easily remedied:

• Noise due to the fact that the appliance is not level – position the appliance using the front adjustable feet. If necessary, place soft material under the rear wheels, particular in case of a tiled floor.
• Friction against other furniture – move the appliance.
• Grinding of drawers or shelves – remove the shelf or drawer and then place it back.
• Noise of colliding bottles – place the bottles apart.

Noises that can be heard during normal use of the appliance are caused by the operation of the thermostat, compressor (activation), cooling system (shrinkage and expansion of the material under the influence of temperature differences and flow of cooling liquid).

product fiche

| INVENTUM
---|---
Model number| KV1615W
Type of appliance| refrigerator/freezer
Category| 7
Energy-efficiency class| A++
Annual energy consumption [Aec]| 192 kWh
Nett capacity – total| 225 litres
Nett capacity – cooling compartment| 159 litres
Nett capacity – freezer compartment ****| 66 litres
Max. storage time in case of power failure| 15 hours
Freezing capacity (kg/24 hour)| 3
Climate class| N/ST/T
Noise level dB(A)| 39 dB
Type of appliance| freestanding
Execution|
Color| white
Number of doors| 2
Door opening reversible|
Eggholder included| 1
Ice cube holder included| –
Number of glass shelves| 3
Total amount of door compartments/ bottle racks| 3
Number of crisper drawers| 1
Number of freezer drawers| 3
CFK/HFK free| free
Type of cooling agent| R600a
Number of compressors| 1
Technical specifications|
Dimensions (wxdxh) in cm| 55,4 x 55,8 x 161,3
Nett weight in kg| 50 kg
Gross weight in kg| 54 kg
Power consumption [W]| 104 w
Rated voltage [V] / frequency [Hz]| 220-240V ~ 50Hz
Lenght of power cord [m]| 2,0
Type of plug| VDE plug 90°

References

• Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!
• Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>