MARLEY 346SITBTTT Stir It Up Wireless Turntable User Guide
- June 4, 2024
- MARLEY
Table of Contents
MARLEY 346SITBTTT Stir It Up Wireless Turntable
ATTENTION, PLEASE READ QUICK START GUIDE BEFORE USE
PRODUCT MAP
LEGEND
- Spindle
- Turntable
- 45 Adaptor
- Balance Weight
- Anti-Skating Knob
- Tone Arm Lift Level
- Tone Arm Rest Holder
- Tone Arm
- Stylus
- Needle Cover
- Off/33/45 Knob
- Power Adaptor With 4
Interchangeable Plugs
FUNCTION LAYOUT
LEGEND
- A. RCA Line Out
- B. Pre-Amp Switch Button
- C. USB to PC Recording
- D. Off/33/45 Knob
- E. Bluetooth® Button
- F. – VOL + Knob
- G. Headphone Jack
- H. Anti-skating Knob
SETUP
POWERING ON YOUR STIR IT UP WIRELESS
- Your Stir It Up Wireless uses an AC power supply and is powered by a standard wall outlet.
- Connect the power adaptor to the wall outlet.
BLUETOOTH® PAIRING
-
Power on the external Bluetooth® device first before turning on the BT function on the Turntable.
-
Press the BT button on the turntable to turn on Bluetooth® transmitter.
-
Press button again to enable the unit to search the Bluetooth® device till BT indicator light becomes solid.
This will indicated your devices are paired. -
Blue LED light flash
-
Blue LED light stable
DISCONNECT BLUETOOTH® PAIRING
Long press and hold the BT button till the BT indicator light turns off. Turntable will then disconnect from external device.
- Blue LED light will turn off.
PLAYING A RECORD
- Put a vinyl record on the turntable.
- Assemble the balance weight and set it to a proper position.
- To adjust the balance weight rotate the balance weight at counter-clock wise.
- Lift and move the tone arm to turntable. Place the tone arm on the edge of the record.
- Turn the RPM Dial knob to select the speed according to the record you are playing.
- The turntable platter will auto stop when the music has ended. Lift the tone arm and place it to tone arm rest manually.
To listen to side B, flip record and repeat the above steps.
33 RPM speed to play corresponding size 33 vinyl disc
45 RPM speed to play corresponding size 45 vinyl disc
To power the unit off Rotate the RPM Dial knob to the off position.
Note:
Remove the needle cover before you balance the tone arm.
Hold tone arm whenever you make any adjustment or action so as to protect the
tone arm.
Do not try to adjust the balance weight while playing a record as this could
break the needle and scratch the record.
Re-secured the tone arm before transportation to protect the needle.
Remove the balance weight before transportation to prevent damage or breakage
to the unit.
Do not stop or turn the platter manually. Moving or jarring the turntable
without securing the Tone arm clamp could result in damage to the Tone arm.
ANTI-SKATING
Normally the anti-skating should be set to its minimum setting. Anti-skate
compensates for inward tracking forces that occur with certain pick-up when
the stylus nears the center of the record. If the turntable is experiencing
excessive skipping while nearing the center spindle, try increase the anti-
skating in the increments indicated on the dial. Start by adding an increment
of 1, test its performance, then increase it more, and so on.
Note: During adjusting the anti-skating knob, leave the tone arm and
balance weight alone to prevent damaging the stylus (needle).
VOLUME CONTROL
Increase Volume: Rotate the Volume Knob clockwise.
Decrease Volume: Rotate Volume Knob counter clockwise.
HEADPHONE OPERATION VIA HEADPHONE JACK
Connect a set of headphone (not included) in the headphone jack
Note: Never put on the headphone till you have plugged in the headphone plug
USB TO PC RECORDING
Download Full instruction for the Audacity Software at:
http://www.audacityteam.org/download/
- Connect the Turntable and the computer via the provided USB cable.
- Follow the instruction of the software installation steps and operation interface.
NON BLUETOOTH® CONNECTION SETUP
CAUTION: Switch off the power to all equipment before making connections. Read the instructions of each component you intend to use with this unit. Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord.
LINE OUT OPERATION
- Switch the PRE-AMP OFF/ON SWITCH to ON position.
- Plug one end of the RCA cable (included) into the LINE OUT socket at the back of the unit. Be sure to match the color with the socket.
- Plug the other end of the cable into the LINE IN socket of your home amplifier device.
- Switch on the unit and the amplifier device you connected.
- Adjust the volume on the amplifier device.
COMPLIANCE INFO
STIR IT UP WIRELESS
READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
CAUTION!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ISEDC STATEMENT
This device complies with Innovation, Science, and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
The device complies with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
BATTERY REPLACEMENT STATMENT IN EUROPE
Your Stir It Up Wireless includes a rechargeable battery designed to last the
lifetime of the product. In the unlikely event that you should require a
replacement battery please contact Customer Services who will supply details
of the warranty and out-of-warranty replacement battery service.
BATTERY DIRECTIVE
This symbol indicates that batteries must not be disposed of in the domestic
waste as they contain substances which can be damaging to the environment and
health. Please dispose of batteries in designated collection points.
WEEE EXPLANATION
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources.
Hereby, FKA Brands Ltd, declares that this radio equipment is in compliance
with the essential requirements and other relevant provisions of Directive
2014/53/
EU. A copy of the Declaration of Conformity can be obtained from
www.thehouseofmarley.co.uk/declaration-of-
conformity
FKA Brands Ltd dengan ini menyatakan bahwa peralatan radio ini mematuhi
persyaratan penting dan ketentuan relevan lainnya dari Arahan 2014/53/EU.
Salinan
Pernyataan Kepatuhan bisa diperoleh dari www.thehouseofmarley.co.uk
/declaration-of-conformity
To prevent possible hearing damage, do not listen at high volume levels for
long periods.
Full instruction and warranty details can be found at
http://www.thehouseofmarley.com/instructionbooks
Marley and the Marley logo are registered trademarks of Fifty-Six Hope
Road Music Limited and the use of such marks by House of Marley is under
license. The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth® SIG, Inc. and any use of such marks by
The House of Marley is under license.
Operating frequency band: 2402 – 2480MHz
CE Maximum radio-frequency power transmitted: -5dBm
DISTRIBUTED BY:
The House of Marley, LLC
3000 North Pontiac Trail, Commerce Township,
MI 48390 USA
Distributed in Europe by FKA Brands Ltd.,
Somerhill Business Park, Five Oak Green Rd,
Tonbridge, Kent TN11 0GP, UK.
IB-EMJT002
EM-JT002
© 2019 House of Marley, LLC.
All Rights Reserved.
©Fifty-Six Hope Road Music Ltd., 2011-2020.
Right of Publicity and Persona Rights.
Fifty-Six Hope Road Music Ltd. EM-JT002
Marley, the Marley logo, Bob Marley and the Bob Marley logo are registered
trademarks of Fifty-Six Hope Road Music Limited and any use of such marks by
The House of Marley is under license. The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks
by The House of Marley is under license.
References
- Bob Marley – Dedicated to the life & legacy of Tuff Gong.
- Declaration of Conformity - The House of Marley UK
- House of Marley Bluetooth Speakers, Headphones, Earbuds & Turntables Inspired by Bob Marley — One Love Movie Giveaway
- Audacity ® | Downloads
- Declaration of Conformity - The House of Marley UK
- House of Marley | Bluetooth Speakers, Headphones & Earbuds inspired by Bob Marley