MIIEGO Axtive M3 Wireless Speaker User Guide

June 5, 2024
MIIEGO

MIIEGO Logo M3 Wireless Speaker
User Guide
MIIEGO Axtive M3 Wireless Speaker

MIIEGO Axtive M3 Wireless Speaker - Overview

  1. EQ
  2. Volume Up / Next Song Press once / Hold
  3. Volume Down / Prev. Song Press once / Hold
  4. LED Bluetooth indicator
  5. Power button: Power on/off, Reset.
  6. Play button: Play, pause, answer call, TWS.
  7. AUX IN port
  8. Charging port
  9. LED indicator for charging
  10. Microphone

SPECIFICATIONS

Bluetooth v5.0.
Rechargeable 2500 mAh Li-ion battery.
Full charging time: around 3.5 hours.
IPX7. BT frequency range: 2402-2480MHz.
Freq. Response: 70Hz-20 KHz.
Charging input power: 5V DC/2A.
RMS audio output: 30W. Impedance: 4Ω.

CARE, MAINTENANCE, SAFETY

Any modification of the product may have consequences for safety, warranty, and proper functioning. Keep out of reach for children and animals. Product storage and working temperature: from -10 Celsius degrees to +40. Do not expose the product to direct sunlight, heat, or naked flames as it may cause damage or explosion. Do not use the product if a part is damaged or defective.
Replace a damaged or defective device immediately. Disconnect the product from the electrical outlet and other equipment if problems occur. Do not charge when the product is wet. Do not leave a battery on prolonged charge when not in use. Do not dismantle, open or shred batteries. Do not drop the product and avoid bumping. This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock etc.

This device contains a lithium accumulator.
Improper use can cause overheating and fire.

Pairing your AXTIVE M3 Bluetooth speaker

  1. Make sure the speaker is charged and turned OFF.
  2. Press and hold the button for 3 seconds until the indicator light flashes WHITE (pairing mode).
  3. Activate Bluetooth on your phone or other device and search for a new Bluetooth device and select MIIEGO AXTIVE M3.

When AXTIVE M3 is connected the WHITE LED light is constantly on.
The speaker will remember your phone/device and automatically reconnect the next time you turn it on.
An unpaired speaker will automatically turn off after 6 minutes.
Charging the AXTIVE M3 speaker
Use a 5V DC/2A USB adapter for charging.
During charging the red right is on. When fully charged the red light is off.
Full charging time is around 3.5 hours with 2A.
Next time charging
When you hear a warning tone every 180 seconds, the battery status is low and needs charging.
Turning Your AXTIVE M3 On and Off
ON: Press the button for 3 seconds until a tone is heard.
OFF: Press the Button until a tone is heard.
Activate Siri on an iOS device: Double press the PLAY button (works only in Bluetooth mode).
Play music from AUX mode
Insert AUX audio cable on the bottom of the speaker. (in AUX mode switching songs on +/- buttons is unavailable)
Pairing and connecting 2 x AXTIVE M3 speakers with TWS
TWS only works when connecting two AXTIVE M3s by MIIEGO® together.
There needs to be a free distance between them.

  1. Turn on both speakers (Bluetooth mode). Make sure they are unconnected.
  2. Press and hold the PLAY button on one speaker for 2 seconds. The product emits a tone to indicate entering TWS-pairing mode.
  3. The product then emits three tones and the LED indicator light (4) will be constantly on. This is then the slave speaker. LED indicator light on the master speaker will flash to indicate successful TWS-pairing.
  4. Activate Bluetooth on your phone/device and connect with the master speaker.

MIIEGO Logo

To prevent possible hearing damage, do not listen to high volume levels for long periods.
Please respect your surroundings, neighbors, and local laws and regulations.
Model No.: AXTIVE M3 Designed in Denmark.
Produced in China. MIIEGO A/S Lejrvejen 4
6330 Padborg Denmark
tel: +45 70 277 887
e-mail: support@miiego.com
www.MIIEGO.com

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals