FALCON RIDGE BC-3400-RW01 Bobcat 3400 Soft Rear Window Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
FALCON RIDGE BC-3400-RW01 Bobcat 3400 Soft Rear Window
Instructions for Installation and Care
BC-3400-RW01
CAUTION : Do not smoke inside the cab or expose the enclosure to direct
flames. Product is FLAMMABLE. Be sure to read these instructions thoroughly
before opening and installing the rear window. The installation is best done
when the temperature is 70 degrees F. or warmer. The temperature affects the
adhesive Velcro, if conditions prevent installing in warmer weather it helps
to store the adhesive Velcro at room temperature prior to installation.
1. Carefully open the carton and unroll the enclosure onto a large flat
surface that is clean and free of dirt or other material that may soil or
scratch the vinyl window.
2. Check over the parts included in the carton with the parts list shown
below:
Velcro hook strip 1 each 30” long
Velcro hook strips 2 each 32” long
Velcro hook strips 1 each 56” long
Enclosure 1 each
If any parts are damaged or missing please contact customer service at
606-845-7439.
3. Lift the bed and begin by applying the 30” adhesive Velcro strip across
the top of the rear of the roll cage. Attach the corresponding sewn-on Velcro
tab to this, then pull the rear window down moderately and place the 55”
Velcro strip along the bottom of the roll cage across the metal strip there.
Clean the areas of any dirt or grease before applying adhesive strips.
4. Next work your way to the sides. Pull the enclosure moderately and evenly
to both sides; go one side at a time. Note the locations of the sewn-on Velcro
and apply the corresponding adhesive Velcro strips to the vertical roll cage
tubes on both sides of the rear of the cab. It is important to pull each side
evenly. Do not pull excessively to either side, or fitment will not be
optimal. Finally, the 6” adhesive strips are for the double-sided 1” wide
wraparound straps down the sides of the enclosure. Congratulations – you are
now finished with the installation.
Cleaning and Storage Recommendations:
1. Before removing the Cab for storage, make sure it is very clean in order
to prevent scratching of the window panels. Clean with a soft rag or sponge
using a mild liquid detergent soap and warm water solution. Never rub the
windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting
to roll for storage.
2. It is important that the Cab be rolled up for storage rather than folding.
Folding will cause damage to the windows!!! Carefully roll up the Cab similar
to the way it was when it was packed at the factory. On a large, clean and
flat surface, fold the doors over the rear panel first, then, interleave the
top and windshield on top of the doors. Begin rolling the Cab into a roll
approximately 8 inches in diameter. Put the rolled Cab back into the carton
for storage at a normal room temperature. It is best not to expose the Cab to
either extreme hot or cold temperatures when storing.
3. A special cleaner conditioner is available from Falcon Ridge that will
greatly increase the service life of the Cab Enclosure. In addition, if
additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!
Return Policy
- If for any reason you choose to return this product it must be returned within 30 days from date item is received. You MUST package the product exactly as it was
- originally packaged from the factory to get a full refund for the product!
- The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between
- and the paper (if available) on both sides of the windows.
- All returned products will be inspected upon arrival at the production facility and must be in unused,
- factory new condition to receive refund – a 25% restocking fee will apply. If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number,
- use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns
- submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must
- first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory new condition.
NOTE : All windshields must be returned with the original protective film
intact and not removed. Do NOT
REMOVE if you have any intentions of returning the item. Refund/ replacement
of a windshield will only be processed on items with original protective film
or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping cost will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty. 30 Day Warranty which includes and is not limited to
replacing the enclosure, tops and/or windshield due to defect of the product.
Please refer to the return policy in this case for more information. 1 Year
Warranty includes any defect in material or workmanship within this time frame
we will gladly correct the problem or replace the enclosure, tops &/or
windshield. Upon submitting for the correction or replacement we will need to
receive pictures of the defect in material or workmanship along with the
receipt from the date of purchase.