FALCON RIDGE Vented Front Windshield for Textron Stampede Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
Vented Front Windshield for Textron Stampede
Instruction Manual
2515 Bypass Rd. Flemingsburg
KY 41041606-845-7439
Vented Front Windshield for Textron Stampede
Instructions for Installation and Care of Textron Stampede 4 Aero-Vent
Polycarbonate Windshield TX-STAMP-4-WD05
NOTICE: Please check the contents of the package for any damage and make
sure all parts fit correctly and you are happy with the product before
removing protective film. Once the film is removed you cannot return the
product for a full refund.
Be sure to read these instructions thoroughly before opening and installing
the Textron Stampede 4 AeroVent Polycarbonate Windshield.
- Check over the parts included in the cartons with the parts list shown below:
Velcro Strap Clamps| 4 each
---|---
1″ Bolts| 2 each
1 ¾” Hex Head Bolts| 2 each
Lock Nuts| 2 each
Nylon Spacers| 4 each
Small Washers| 2 each
Plastic Thumb Nuts| 2 each
Slide Fasteners| 10 each
48” End Bulb Rubber Gasket| 1 each
Vent Sliders| 2 each
Lexan Windshield| 1 each
If any parts are damaged or missing please contact customer service at 606-845-7439.
-
Start by pulling it out of the box, find a clean area to lay it down, and install the hardware. Begin by peeling off the protective film. Next take the 48″ piece of rubber gasket and starting at one end firmly place it along the entire bottom edge of the Windshield as shown in the photo below.
-
Next prepare the vent slider to be installed on the windshield. Take the two hex head bolts, 4 nylon spacers and two lock nuts and attach them to the vent sliders as shown in the photo below.
-
Take the spacers and slide two of them over the bolt as shown below
-
Now insert the bolt in the small holes and screw on the lock nuts so the end of the bolt is flush with the outside edge of the lock nut. Make sure that you place the bolt-through hole on each slider so that they are mirror images of each other.
-
Now place the sliders on the inside surface of the windshield. The ends of the sliders with the point should be facing away from the center of the windshield. And place the plastic slide fasteners through the slots on the slider and into the holes in the windshield. The lock nuts should be in the large slots of the windshield.
-
You are now ready to install the windshield on your roll cage. Place the windshield on the vehicle first. Making sure that the bottom of the windshield overlaps the top edge of the hood to reach the bottom hood section as shown in the photo below.
-
Then take the four Velcro clamps and place them through the square holes then wrap the strap around the roll cage and under the wire as shown in the photo below.
-
Then just Pull the strap back around the bar and attach it to the Velcro.
-
Next attach the two loom clamps along the top of the windshield as shown in the diagram and photo on the next page.
-
Now you are ready to take it out and enjoy. To clean the windshield, always clean using a liquid of some sort to decrease the chance of scratches. We recommend using microfiber cloths that are readily available at any dollar store. Any window cleaner will work fine; just remember to use a soft clean rag or micro-fiber cloth to clean it.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date the item is received. You MUST package the product
exactly as it was originally packaged from the factory to get a full refund
for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory-new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE if you have any intentions of returning
the item. Refund/ replacement of a windshield will only be processed on items
with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, a credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping costs will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops and/or windshield due to defects of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>