INVENTUM AKD6005ZWA Wall Mount Cooker Hood User Manual

June 5, 2024
INVENTUM

INVENTUM AKD6005ZWA Wall Mount Cooker Hood

INVENTUM AKD6005ZWA Wall Mount Cooker Hood-prod

INSTRUCTION

INVENTUM AKD6005ZWA Wall Mount Cooker Hood-fig1 INVENTUM AKD6005ZWA Wall Mount Cooker Hood-fig2 INVENTUM AKD6005ZWA Wall Mount Cooker Hood-fig3 INVENTUM AKD6005ZWA Wall Mount Cooker Hood-fig4

Introduction

HOW TO USE THIS DOCUMENT

  1. Read this document completely. Make sure that you know and understand all the instructions.
  2. Obey the safety instructions to prevent injury and/or damage to the appliance and its surroundings.
  3. Do the procedures completely and in the given sequence.
  4. Keep this document in a safe area for future use. This document is a part of the appliance.

SYMBOLS USED IN THIS DOCUMENT

Safety symbol Function Description
**** ****

Warning

| “Warning” means that injury or death is possible if you do not obey the instructions.
|

Caution

| “Caution” means that damage to the appliance is possible if you do not obey the instructions.
|

Note

| ****

“Note” is used to give additional information.

Safety

GENERAL SAFETY INSTRUCTIONS

  • Fully read the instruction manual prior to using the appliance.
  • Carefully store the instruction manual for future reference or subsequent owners.
  • Only use this appliance for the purpose described in the instruction manual.
  • The appliance is intended for domestic use and the household environment only.
  • Never leave the appliance unattended when in use.
  • The manufacturer is not responsible for damage which is causes by improper use or incorrect operation.
  • Warning:
  • Danger of suffocation! Packaging material is dangerous to children. Keep the packaging material out of the reach of children.
  • This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised by someone who is responsible for their safety, or have been instructed in how to use the appliance safely and have understood the risks involved in not using it properly.
  • Children must not play with the appliance.
  • Cleaning and user maintenance must not be performed by children unless they are over 15 years of age and are supervised.
  • Keep children below the age of 8 years old at a safe distance from the appliance and the mains power cable.

SAFETY INSTRUCTIONS FOR INSTALLATION

  • Only connect the appliance to alternate current, to an earthed mains socket. Make sure that the voltage in your home corresponds with the voltage printed on the type plate of the appliance.
  • Do not connect the outlet to a flue duct that is used for other appliances.
  • The appliance may only be fitted by a certified installer.
  • Follow the installation requirements.
  • Do not install the appliance in case of damage.
  • Always use the original cord and plug to connect the appliance.
  • The electrical connection must meet national and local regulations.
  • The mains socket and mains plug must always be within reach.
  • If the device is a ceiling unit, the device must always be removable (do not seal).
  • If the motor can be placed externally (depending on the model), keep in mind that the motor must always be accessible for inspection.
  • Warning:
  • This appliance should be repaired by an authorized service only. Do not open the casing of the appliance.
  • The manufacturer is not responsible for damage which is caused by improper use or incorrect operation.

SAFETY INSTRUCTIONS FOR OPERATION

  • Warning:
    Danger of death! Risk of poisoning from flue gases that are drawn back in. Do not use the cooker hood without sufficient ventilation at the same time as a cooker that uses the air in a room. Cookers that use the air in a room (for example, appliances that work on gas, oil, wood or coal or other appliances such as geysers and hot water appliances) draw the combustion air from the room and discharge the gases via a drain to the outside. Combined with a cooker hood, the air is drawn out of the kitchen and adjacent rooms. If there is insufficient air supply, this creates a vacuum. Toxic gases from the drain are sucked back into the living area. Always make sure that there is sufficient ventilation.

  • Adequate incoming air must therefore always be ensured.

  • An incoming/exhaust air wall box alone will not ensure compliance with the limit.

Safe operation is possible only when the partial vacuum in the place where the heat producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or by other technical means. In any case, consult a certified installer. He is able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you.

  • Unrestricted operation is possible if the cooker hood is operated exclusively in the circulating-air mode.

  • Obey the local standards for extracting air. Do not operate the appliance with an external timer or a separate remote control system.

  • Do not use the appliance without the grease filter.

  • Do not lean against the appliance.

  • Items placed on the appliance may fall down. Do not place any objects on the appliance.

  • Make sure that there is sufficient ventilation when you use the appliance together with a gas hob.

  • Clean or replace the grease filter and/or the carbon filter regularly. There is a risk of fire.

  • Cooking with fat or oil on an unattended appliance can be dangerous and could result in fire.

  • Note:
    Intensive use can cause condensation on the appliance. You can easily remove condensation with a dry cloth.

  • Warning:

  • Risk of fire

  • Excess grease in the grease filter could result in fire.

  • Do not work with open fire (flambé).

  • Always use the grease filter.

  • Warning:

  • Risk of fire

  • Cooking with fat or oil on an unattended appliance can be dangerous and could result in fire. Do not extinguish a fat or oil fire with water. Switch off the appliance and cover the flames with a lid or fire blanket.

  • Warning:
    Risk of electric shock Do not use the appliance when the plug, the cord or the appliance has damage, or when the appliance does not operate correctly. Contact the retailer or the Customer Service Department. Do not replace the plug or the cord yourself.

  • Warning:
    Risk of injury! Risk of trapping body parts when opening and closing the glass front. Do not reach into the area behind the glass panel, and keep your fingers away from the hinges.

  • Warning:
    Hazard due to magnetism! Permanent magnets are inserted in the appliance front. They may affect electronic implants, e.g. heart pacemakers or insulin pumps. Wearers of electronic implants must stay at least 10 cm away from the front of the appliance.

SAFETY INSTRUCTIONS FOR CLEANING AND MAINTENANCE

  • Do not use a high-pressure cleaner or steam cleaner to clean the appliance.

  • Warning:

  • Risk of electric shock

  • Make sure that the appliance is off when you perform repairs or cleaning.

  • The appliance must be cleaned at least once a month. Failure to clean the appliance or to replace the filters can result in fire.

  • The grease filter becomes hot during use. After operation, wait at least 30 minutes before cleaning.

  • The appliance has sharp edges, be careful during cleaning and maintenance.

  • Caution:
    Surface damage due to incorrect cleaning.

  • Do not use abrasive cleaning agents or cleaning agents that contain alcohol.

  • Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners on the operator controls.

  • Defective parts may only be replaced by original parts. Only for those parts will the manufacturer be able to guarantee that they meet the safety requirements.

ENVIRONMENTAL PROTECTION
The appliance is energy-efficient. Save even more energy when using the appliance with the following tips, and how to dispose of your appliance in an environmentally-friendly way.
Saving energy

  • Ensure that there is a sufficient supply of air during cooking, so that the cooker hood can work efficiently and with a low level of operating noise.
  • Adjust the speed to the intensity of the cooking fumes. Only use the booster mode where this is required. A lower fan speed means that less energy is consumed.
  • If there are intensive cooking fumes, select a higher speed in time. If cooking fumes have already spread in the kitchen, the cooker hood must be operated for longer.
  • Switch off the appliance if it is no longer required.
  • Switch off the lamps when it is no longer required.
  • Clean and, if required, replace the filter at regular intervals in order to increase the effectiveness of the ventilation system and to prevent the risk of fire.

Environmentally-friendly disposal

  • Recycling – WEEE
  • Dispose of packaging in an environmentally-friendly manner.
  • This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Description

INTENDED USE
The appliance is intended to be used for handling the air of cooking fumes. Do not use the appliance for any other purpose than described in this document.
WALL-MOUNT COOKER HOOD

  • Shaft
  • Control panel
  • Cooker hood
  • Lights
  • Grease filters

CONTROL PANEL

  • Lamp button
  • Speed button 1
  • Speed button 2
  • Speed button 3
  • Speed button 4
Item Function
Lamp button To activate/deactivate the lamps.
Speed button 1 •    To start and stop the appliance at the lowest speed.

•    To activate the automatic switch-off mode.

Speed button 2| •    To start and stop the appliance at the middle speed.

•    To activate the automatic switch-off mode.

Speed button 3| •    To start and stop the appliance at the highest speed.

•    To activate the automatic switch-off mode.

Speed button 4| To activate the booster mode.

WORKING PRINCIPLE COOKER HOOD
The appliance is used for handling the air of cooking fumes. The appliance can be installed in two different ways.
Extracting (A)
The cooking fumes are extracted outside.

Warning:
Never connect the pipe to a duct that contains gas or other fuels.

Recirculating (B)
The cooking fumes go through a carbon filter or a plasma filter. The filter purifies the fumes and recirculates these back to the kitchen.
A good outflow of the air is necessary.
Extra information

  • Note:
    New houses may no longer vent outside.

  • For recirculation, it is necessary to use carbon filters or a plasma filter. For more information on the differences between carbon and plasma, filters go to the website www.invented.EU.

  • Attention:
    The carbon filters and plasma filters are not included. You need to order these separately.

Installation

SAFETY INSTRUCTIONS FOR INSTALLATION

  • Install the appliance with two people.
  • Wear safety gloves. The appliance has sharp edges.
  • The distance between the lowest point of the appliance and a gas hob must be a minimum of 75 cm. For an electrical, ceramic or induction hob, the minimum distance must be 65 cm. NOTE: in case of a diagonal cooker hood, the installation distance can be less. See the dimensions in the figures.
  • Always obey the manual of the cooker or the gas hob if that manual states a larger distance.
  • Warning:
  • Risk of electric shock
  • Always use the screws or fasteners that are stated in the installation instructions. Failure to do so can result in electric shock.

UNPACKING

  1. Remove the packaging.
  2. Examine the appliance for damage.
  3. Make sure that the voltage is the same as on the type plate.

PREPARING FOR INSTALLATION

  1. Mark the wall from the middle of the hob. Make sure that you keep the minimum distance between the hob and the appliance into account (D1 or D2) plus the height of the appliance (B).
  2. Mark the position for the screws for the cooker hood according to the dimension (A).
  3. Hold the support for the shaft at the desired height.
  4. Mark the position for the openings.

INSTALLING THE SCREWS AND THE SUPPORT Preliminary requirements

  • Plugs Ø 8 mm x 40 mm (4x)
  • Screws Ø 4.5 mm x 50 mm (4x)

Procedure

  1. Drill a hole at the marked positions. Use a Ø 8 mm drill.
  2. Install the plugs (A).
  3. Install the screws (B).
  4.  Install the support for the shaft (D). Use the screws (C).

PREPARING THE INSTALLATION OF THE HOSE FOR EXTRACTION MODE
The hose can be installed either via the wall or via the ceiling.
Preparing the installation of the hose via the wall

  1. Drill a hole (A) in the wall with a diameter of 160 mm.

Preparing the installation of the hose via the ceiling

  1. Drill a hole (A) in the ceiling with a diameter of 160 mm.
  2. Make sure that the hole is positioned a minimum of 100 mm (B) from the wall.

PREPARING THE INSTALLATION OF THE MAINS SOCKET

  1. Mark the position for the mains socket. Obey these requirements:
    • The width of the mains socket must be the width of the shaft (A) minus 20 mm.
    • The position of the mains socket must be at a minimum of 10 mm (B) below the support of the shaft and at a minimum of 300 mm (C) above the support of the cooker hood.

INSTALLING THE APPLIANCE Preliminary requirements

  • Screwdriver

Warning:
Two people are required to install the appliance.

Procedure

  1. Put the appliance (A) on the screws (B).
  2. Open the cover of the appliance.
  3. Tighten the screws to fasten the appliance to the wall. Use the screwdriver.

INSTALLING THE HOSE

  1. Install the hose (A) to the appliance (B) and to the exhaust opening (C). Use the hose clamps.

INSTALLING THE SHAFT Preliminary requirements

  • Screws Ø 3.9 mm x 9.5 mm (4x)

Procedure

  • Put the shaft (A) on the appliance (B).
  • Move the top part of the shaft up.
  • Install the screws (C).

CONNECTING THE APPLIANCE

Caution:
If you wish to make a fixed connection, make sure that there is an omnipolar switch with a minimum contact separation of 3 mm installed in the supply cable.

  1. Make sure that the voltage in your home corresponds with the voltage of the appliance.
  2. Use the supplied mains cable to connect the appliance to the mains socket.

Operation

STARTING AND STOPPING THE APPLIANCE

  1. It is advised that you start the appliance a few minutes before you start cooking.
  2. Touch the button 1, 2 or 3 to start the appliance. The appliance starts at the set speed.
  3. Touch the same button 1, 2 or 3 again to stop the appliance.

Note:
Make sure that the appliance operates for 5 to 10 minutes after you finish cooking.

ADJUSTING THE SPEED

  1. Make sure that the appliance is on speed 1.
  2. Press one of the buttons 2 or 3 to increase the speed.
  3. Press a lower button to decrease the speed.

USING THE BOOSTER MODE
The booster mode provides extra speed to the appliance.

  1. Make sure that the appliance is on.
  2. Touch the button 4.
    The booster mode now works for 5 minutes. After 5 minutes, the speed returns to 3.

USING THE AUTOMATIC SWITCH-OFF MODE
In automatic switch-off mode, the appliance automatically switches off after 15 minutes.

  1. Make sure that the appliance is on.
  2. Adjust the speed to setting 1, 2 or 3.
  3. Touch and hold the button 1, 2 or 3 for 3 seconds to activate the automatic switch-off mode. The setting flashes. The speed flashes and the timer is activated.

USING THE LAMPS

  1. Touch the lamp button to activate or deactivate the lamps.

Cleaning and maintenance

SAFETY INSTRUCTIONS FOR CLEANING AND MAINTENANCE

Warning:
Clean the appliance and the grease filters regularly. Failure to do so may result in fire.

Caution:
Make sure that the appliance is off and that the mains plug is removed from the mains socket.
Caution:
Do not use abrasive cleaning agents or cleaning agents that contain alcohol.

CLEANING THE APPLIANCE

  1. Clean the inside and the outside of the appliance. Use hot water and a mild cleaning agent.
  2. Clean the control panel of the appliance. Use a damp cloth.

CLEANING THE GREASE FILTER

  1. Open the cover of the appliance.
  2. Push the latch (A).
  3. Support the grease filter (B) and remove it from the appliance.
  4. Clean the grease filter. Use hot water and a mild cleaning agent.
  5. If necessary, clean the grease filter in a dishwasher. Use a program with a low temperature.
  6. Make sure that the grease filter is dry before installing.

REPLACING THE CARBON FILTER (OPTIONAL)

Note:
The carbon filter must be replaced every 4 months.
Note:
This procedure is only valid if you installed the carbon filter with your appliance.

  1. Open the cover of the appliance.
  2. Remove the grease filter.
  3. Replace the carbon filter (A).
  4. Install the grease filter.

REPLACING THE LAMP Preliminary requirements

  • Lamp 3 W LED GU10 (2x)

Procedure

  1. Remove the grease filter.
  2. Push the lamp holder (B) down from the inside.
  3. Carefully turn the defective lamp (A) clockwise out of the holder.
  4. Replace the lamp with a new one.
  5. Turn the new lamp counterclockwise into the holder.
  6. The lamp holder will spring back in position by itself. If this doesn’t happen, carefully bend the holder back in position.
  7. Install the grease filter.
  8. Repeat the steps for the second lamp.

Troubleshooting

GENERAL TROUBLESHOOTING PROCEDURE

  1. Try to find a solution for the problem with the help of the troubleshooting table.
  2. If you cannot find a solution for the problem, contact the Inventum-servicedienst.

TROUBLESHOOTING TABLE

Problem Possible cause Possible solution


The motor does not operate.

| The mains plug is not connected.| Connect the mains plug.


There is no mains supply.

| •    Do a check if the mains plug is correctly connected to the mains socket.

•    Make sure that the mains supply is on.

There is a problem with the fuse.| Do a check on the fuse box.
The appliance does not operate correctly or makes an unusual sound.| The dimension of the outlet is not correct.| Make sure that you use the correct dimension during installation. Refer to chapter ‘Installation’.
The outlet has a blockage.| Remove the blockage.
The grease filter is dirty.| Clean the grease filter. Refer to section ‘Cleaning the grease filter’.
The carbon filter is worn.| Replace the carbon filter. Refer to section ‘Replacing the carbon filter (optional)’.

Technical data

TECHNICAL SPECIFICATIONS OF THE COOKER HOOD

Item Specification
Energy efficiency class B
Air flow rate (at min/max speed) [m3/h] 260/430
Air flow rate (at high speed/turbo mode) [m3/h] 665
Lighting efficiency class A
Grease filtering efficiency class E
Power consumption in standby mode (Ps) [W] 0.45
Noise level at min/max speed [dB] 51/62
Noise level at min/max speed (at high speed/turbo mode) [dB] 68
Color Black
Number of motors 1
Item Specification
--- ---
Lamp type 2 x 3W
Number of grease filters 2
Carbon filter type* KB91
Plasma filter type* IPF650R
Width [mm] 600
Diamater exhaust [mm] 150
Power consumption [W] 266
Rated voltage [V] 220-240
Frequency [Hz] 50

General terms and conditions of service and warranty

We do not need to remind you of the importance of service. After all, we develop our products to a standard so that you can enjoy them for many years, without any concerns. If, nevertheless, there is a problem, we believe you are entitled to a solution straight away. Hence our products come with an exchange service, on top of the rights and claims you are entitled to by law. By exchanging a product or part, we save you time, effort and costs. 2-year full manufacturer’s warranty

  1. Customers enjoy a 2-year full manufacturer’s warranty on all Inventum products. Within this period, a faulty product or part will always be exchanged for a new model, free of charge. In order to claim under the 2-year full manufacturer’s warranty, you can either return the product to the shop you bought it from or contact the Inventum costumer service department via the form at ”.
  2. The 2-year warranty period starts from the date the product is bought.
  3. In order to claim under the warranty, you must produce a copy of the original receipt.
  4. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

5-year Inventum warranty

  1. Inventum offers a 5-year warranty on most large domestic appliances and a selection of small domestic appliances. This 5-year Inventum warranty consists of a 2-year full manufacturer’s warranty, extended by a further 3-year warranty. The only thing you need to do to qualify for the 3-year extended warranty is to register the product within 45 days of purchase. You can read more about registering the product in the following paragraph.
  2. In accordance with the 5-year Inventum warranty provisions, a faulty product or part will always be exchanged for a new model during the first 2 years under the warranty. During the 3rd to 5th year under the warranty, you will only pay the costs of exchange. The current costs of exchange are listed at ”.
  3. In order to claim under the 5-year Inventum warranty, you can either return the product to the shop you bought it from or contact the Inventum costumer service department via the form at ”.
  4. The 5-year warranty period starts from the date the product is bought.
  5. In order to claim under the warranty, you must produce a copy of the original receipt.
  6. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

Product registration

  1. The 3-year extended warranty is easy to obtain, free of charge, by registering the product within 45 days of purchase, via the website ”. If you did not register the product within 45 days of purchase, you can still do so up to 2 years after the purchase date. However, there will be a charge. The one-off registration charge is € 89 for each separate product. Registration is possible only for products that are subject to the 5-year Inventum warranty. Whether the product qualifies for the 5-year Inventum warranty is stated in the product user manual and in the product information sheet, on Inventum’s website.
  2. The warranty period always starts from the date the product is bought. If the product is registered for the extended warranty at a later date, the warranty period still starts from the original date of purchase.
  3. The 3-year extended warranty can only be applied for if you are in the possession of a copy of the original receipt and the Inventum 5-year warranty certificate.

Large domestic appliances

  1. Breakdowns or faults in large domestic appliances (separate and built-in white goods) can be registered via the form at ”, by calling the Inventum costumer service department or in the store where you bought the device. The telephone number of the costumer service department can be found at ”.
  2. In the event of breakdowns or faults in large domestic appliances, Inventum will have the option to have a service engineer inspect the faulty device onsite at the customer in the Netherlands and to carry out repairs, there and then. The Inventum customer service department can also decide to have the device exchanged.
  3. If you suffer a breakdown or fault in a large domestic appliance during the first 2 years from the date of purchase, Inventum will not charge any costs for the exchange, call-out or for parts and labour.
  4. If you registered the product as described before at ” and you subsequently report a breakdown of a large domestic appliance in the 3rd to 5th year of the date of purchase, the 5-year Inventum warranty applies and the device will be repaired or exchanged, free of charge. In the event of a repair or exchange of the device, you only pay the costs of exchange. The current costs of exchange are listed at ”. If you did not register the product, the 3- year extended warranty does not apply.
  5. When reporting a breakdown or fault, a service engineer will contact the customer within 1 working day in order to make an appointment. When the report is made in a weekend or during a public holiday, this will be the next working day.
  6. If you report a breakdown or fault via the form at ”, you will be kept informed of the progress via mobile messages and e-mail.
  7. The warranty period starts from the date the product is bought.
  8. In order to claim under the warranty, you must produce a copy of the original receipt and the Inventum 5-year warranty certificate.
  9. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

Breakdowns or faults outside the warranty period

  1. Breakdowns or faults in small or large domestic appliances outside the warranty period can be reported to the customer services department via the form at ” or by calling the customer services department.
  2. The customer services department may ask you to send the product for inspection or repair. The costs of dispatch will be at your expense.
  3. The inspection to establish whether the repair is possible involves a charge. You need to grant your permission for this, in advance.
  4. In the event of a large domestic appliance, Inventum, at your request, can send out a service engineer. In that case, you will be charged the call-out costs, as well as parts and labor.
  5. In the event of an instruction to repair, the repair costs must be paid in advance. In the event of a repair by a service engineer, the costs of the repair must be settled with the engineer on site, preferably by means of PIN payment.

Warranty exclusions

  1. The following is excluded from the aforesaid warranties:
    • normal wear and tear;
    • improper use or misuse;
    • insufficient maintenance;
    • failure to comply with the operating and maintenance instructions;
    • unprofessional installation or repairs by third parties or the customer himself;
    • non-original parts used by the customer;
    • use for commercial or business purposes;
    • removal of the serial number and/or rating label.
  2. In addition, the warranty does not apply to normal consumer goods, such as:
    • dough hooks, baking tins, (carbon) filters, etc.;
    • batteries, bulbs, carbon filters, fat filters, etc.;
    • external connection cables;
    • glass accessories and glass parts such as oven doors;
    • and similar items.
  3. Transport damage not caused by Inventum is also excluded. Therefore, inspect your new device before starting to use it. If you detect any damage, you must report this to the store where you purchased the product within 5 working days, or to the Inventum customer service department via the form at ”. If transport damage is not reported within this period, Inventum does not accept any liability in this respect.
  4. The following are excluded from warranty and/or replacement: faults, loss of, and damage to the device as a result of an event that is normally insured under the home contents insurance.

Important to know

  1. The replacement or repair of a faulty product, or a part thereof, does not lead to an extension of the original warranty period.
  2. Parts that have been replaced, packaging material, and exchanged devices are taken back by the service engineer and become the property of Inventum.
  3. If a complaint is unfounded, all costs arising from it will be at the customer’s expense.
  4. Following the expiry of the warranty period, all costs of repair or replacement, including administration costs, dispatch and call-out charges, will be charged to the customer.
  5. Inventum cannot be held liable for damage as a result of devices built-in incorrectly.
  6. Inventum cannot be held liable for damage caused by external events unless this liability arises from mandatory statutory provisions.
  7. These warranty and service provisions are governed by Dutch law. Disputes will be settled exclusively by the competent Dutch court.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals