INVENTUM JVL2600 Fridge Freezer Instruction Manual
- June 5, 2024
- INVENTUM
Table of Contents
INVENTUM JVL2600 Fridge Freezer
Tools you will need
Reversing the door openings
The doors of the appliance can be opened on the right or left side. In order
to reverse the door openings, please observe the instructions below. It would
be best to do this with two people.
Attention: switch off the thermostat and remove the plug from the socket.
Remove all items from the refrigerator, including the shelves and drawers,
before reversing the door opening.
-
Use a putty knife or thin-blade screwdriver to remove the screw hole cap (left) a, then remove the upper hinge cover (right) b.
-
Unscrew the special self-tapping screws a and remove the upper hinge.
Remark: During this step, hold the upper door with your hand to prevent it from falling. -
Remove the upper hinge axis, transfer it to the reversed side and tighten securely. Put it down for late use.
-
Remove the upper door from the middle hinge by carefully lifting the door straight up.
Remark: when removing the door, watch for the washer(s) between the center hinge and the bottom of the upper door that may stick to the door. Do not loose. -
Place the upper door on a smooth surface with its panel upwards. Loosen screw a and remove the stop block b.
-
Install these 2 parts a and b to the left side and tighten securely.
-
Unscrew the two special self-tapping screws which are used for fixing the middle hinge part, then remove the middle hinge part that hold the lower door in place.
Remark: when removing the door, watch for the washer(s) between the center hinge and the bottom of the upper door that may stick to the door. Do not loose. -
Place the lower door on a smooth surface with its panel upwards. Loosen the screw a and remove the stop block b.
-
Install these 2 parts a and b to the left side and tighten securely.
-
Change the screw hole caps on the middle cover plate from the left to the right (as shown in the figure).
-
Lay the refrigerator backwards on soft foam packaging or similar material to prevent damages. Remove both adjustable bottom feet b, and remove the lower hinge c by unscrewing the special self-tapping screws a.
-
Change the screw hole caps on the bottom cover plate from the left to the right (as shown in the figure).
-
Replace the lower hinge to the left side and fixate it with the special self-tapping screws. Replace the adjustable bottom feet to the other side and fixate them.
Carefully place the refrigerator upright. -
Place the lower door on the bottom hinge and support it. Make sure the door is aligned.
-
Flip over the middle hinge a 180 degrees and fix it on the other side of the appliance. Place the middle hinge axis into the upper hole of the lower door and tighten the screws b of the hinge.
-
In the case of the refrigerator with the display on the door, you remove top left part from the upper cover and remove part. Then remove part and place part in the top right corner of the upper cover. See the step above, install part on the top left side of the upper cover. Install part on the top right side of the upper cover. Skip this step for the refrigerator with display on the door.
-
Corner cover (left)
-
Electric connector (left)
-
Corner cover (right)
-
Electric connector (right)
MODEL WITH DISPLAY
- Place the upper door on the middle hinge. Make sure the door is aligned.
- Place the upper hinge a. Make sure the upper hinge axis fits in the upper hole of the upper door. Remark: please support the upper door with your hand when doing this. Fixate the upper hinge with the self-tapping screws.
- Place the screw hole cap a and place the other hinge cover b (which is in the plastic bag).
Place the shelves and drawers back in the refrigerator. Allow the appliance to rest for 2 to 3 hours before inserting the plug in the socket.
Safety instructions
-
Please read these instructions before operating the appliance and retain for future use.
-
Only use this appliance for the purposes described in the instruction. The appliance is suitable for storing food. It is possible to freeze fresh food in the freezer section.
-
Only connect the appliance to alternate current, to an earthed wall socket, with a mains voltage that corresponds with the information provided on the information plate of the appliance.
-
Do not use single/multiple adapters or extension cords.
-
Do not use the appliance if the plug, cord or appliance are damaged, or if the appliance no longer functions properly or if it is damaged in any other way. If this is the case, consult the shop or our technical service. Never replace the plug or cord yourself.
-
The appliance must be moved and installed by two or more persons.
-
Be careful when moving the appliance to prevent the floor from getting damaged.
-
During installation, do make sure the power cable is not damaged.
-
Check that the appliance is not placed too close to a heat source.
-
In order to ensure proper ventilation, a free space of 10 cm should be maintained around the appliance and 30 cm from the top.
-
Do not place anything on top of the appliance, such a an oven or microwave.
-
Never cover the ventilation openings.
-
Make sure the cooling pipes do not get damaged.
-
Install the appliance on a sturdy, flat and stable surface.
-
Install the appliance in a dry and well ventilated room. The appliance is intended for use in a room where the ambient Climatic class temperature falls within the applicable class, depending on the climate class found on the information plate on the back of the appliance.
-
Do not store explosive or highly flammable substances in the appliance. The vapors could cause a fire hazard or an explosion.
-
Do not store glass bottles or jars with liquids in the freezer, as they could break when frozen.
-
Do not use mechanical, electrical or chemical agents to speed up the defrosting process.
-
Make sure that children are unable to play with the appliance, such as hide in it. This is dangerous.
-
Keep the appliance out of reach of children. Children do not see the dangers when handling electrical appliances. Therefore, never allow children to work with electrical appliances without supervision. Keep the appliance and cord out of reach of children younger than 8 years of age.
Note: Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances. -
The appliance can be used by children of 8 years and older and persons with a limited physical, sensory or mental capacity or lack of experience or knowledge, provided they use the appliance under supervision or have been instructed about its safe use and understand the hazards involved.
-
The appliance may not be cleaned or maintained by children, unless this is done under supervision.
-
Repairs to electrical appliances should only be performed by skilled persons. It is dangerous to perform a repair whereby the base unit of the appliance must be opened.
-
Only use and store the appliance indoors.
-
Never bend the power cord sharply or allow it to run across hot parts.
-
Always remove the plug from the socket when the appliance must be cleaned or repaired.
-
Never use the appliance with parts that are not recommended or supplied by the manufacturer.
-
Do not pull the cord and/or appliance to remove the plug from the wall socket. Never touch the plug with wet or moist hands.
-
Be careful with ice cubes and ice pops. If these are consumed directly out of the freezer, there is a risk of frostbite.
-
Never submerge the appliance, cord or plug in water.
-
The appliance cannot be used with a timer or separate remote control.
-
This appliance is only suitable for household use. If the appliance is not used as intended, no compensation can be claimed in case of defects or accidents and the warranty will be invalidated.
-
If you decide not to use the appliance any more due to a defect, we recommend cutting off the cord after removing the plug from the wall socket. Household appliances are not normal waste. Take the appliance to the waste processing department concerned of your municipality.
Refrigerant
The refrigerant isobutene (R600a) is contained within the refrigerant circuit
of the appliance, a natural gas with a high level of environmental
compatibility, which is nevertheless flammable. During transportation and
installation of the appliance, ensure that none of the components of the
refrigerant circuit becomes damaged. The refrigerant (R600a) is flammable.
WARNING: Refrigerators contain refrigerant and gases in the insulation.
Refrigerant and gases must be disposed of professionally as they may cause eye
injuries or ignition. Ensure that tubing of the refrigerant circuit is not
damage prior to proper disposal.
WARNING: Risk of fire/ flammable materials
If the refrigerant circuit should be damaged:
- Avoid open flames and sources of ignition.
- Thoroughly ventilate the room in which the appliance is situated. It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire, and/or electric shock.
Appliance description
- Internal lighting
- Glass shelves
- Fresh box drawer
- Crisp drawer
- Freezer drawers
- Adjustable feet
- Door – freezer section
- Door – cooler section
- Bottle compartment
- Door compartments
- Egg tray – 2 pcs. – not shown
- Ice cube tray – not shown
Before the first use
Before using the appliance for the first time, you should proceed as follows: carefully unpack the appliance and remove all packaging material and any promotional stickers. Keep the packaging (plastic bags, polystyrene and cardboard) out of the reach of children. After unpacking the appliance, check it for external damage that may have occurred during transport.
Place the appliance on a sturdy, flat surface and make sure there is enough space all around for sufficient ventilation. A minimum space of 10 cm is required between the appliance and the surrounding walls and keep 30 cm clear above the appliance. In this way the appliance is able to release heat properly, cool well and function in an energy efficient way. You can use the adjustable feet to level the appliance. Do not place the appliance near heat sources such as central heating or a stove. Do take note of the climate class of the appliance. When placed in a room that is too cold, the refrigerator will not function properly.
After placing the appliance, leave it for at least 3 hours before inserting
the plug in the socket.
First clean the interior of the appliance. Use warm soapy water with, for
instance, washing-up liquid, all-purpose cleaner or soda. Wipe the inside of
the appliance after cleaning with clean water and properly wipe everything
dry. Leave the appliance to dry for 1 to 2 hours.
Usage
The control unit of the appliance is located on the outside. Check that the
voltage corresponds with what is stated on the information plate and insert
the plug in the socket.
Instruction: the recommended temperature setting is 4°C. For the freezer
section this is -18°C.
Instruction: The amount of food, the ambient temperature, the frequency
of opening the door and the position
of the appliance have an effect on the temperature in the appliance. The
temperatures in the refrigerator can differ from the temperature on the
display. Take this into account when setting the thermostat.
Control panel on the outside of the door
SETTING THE TEMPERATURE OF THE COOLER SECTION
Press on the control panel on the key ZONE CHOICE to change the temperature
of the appliance. The symbol of the cooler section lights up. Press the key
SET TEMP until the desired temperature is shown in the display. The
temperature of the cooler section can be set between 2°C and 8°C.
The temperature is set in the following sequence:
SETTING THE TEMPERATURE OF THE FREEZER SECTION
On the control panel, press ZONE CHOICE to change the temperature of the freezer section. The symbol of the freezer section lights up. Press the key SET TEMP until the desired temperature is shown in the display. The temperature of the freezer section can be set between -14°C and -24°C.
The temperature is set in the following sequence:
After setting the temperatures, the appliance continues to cool until the set
temperatures have been reached. Allow the appliance to reach the required
temperature with no food. Usually this will take 2 to 3 hours. After this, you
are able to fill the appliance with food.
If the ambient temperature rises, set the appliance to a lower temperature
position in order to be able to guarantee the interior temperature.
SUPER FREEZING
Use this mode to quickly freeze food that is not yet frozen. In order to be
able to freeze fresh food quickly, the temperature of the freezer section
should be lowered timely in advance. It may be necessary to activate the super
freezing mode 24 hours in advance.
When this mode is selected, the temperature of the freezer section
automatically drops to -24°C for a maximum period of 52 hours. After 52 hours
the temperature of the freezer section returns to the preset temperature.
To activate the super freezing mode, press the key SUPER until the light
lights up on the display. To switch off the mode, press the key SUPER until
the light no longer lights up.
ECO MODE
This mode helps prevent energy waste when the refrigerator is not used as
normally, such as during your holidays. When this mode is selected, the
temperature of the freezer section is automatically set to -17°C and the
cooler section is set to 6°C.
To activate the ECO MODE, press the key ECO MODE until the symbol lights up on
the display. To switch off the mode, press the key ECO MODE until the symbol
no longer lights up.
SWITCHING ON AND OFF
You can switch the appliance on and off with the on/ off key .
To switch the appliance off, press the on/ off key for 3 seconds. You will
here a sound and in the display OF appears.
To switch the appliance on, press the on/ off key for 3 seconds. You will here
a sound and the appliance switches on.
DOOR OPEN ALARM
If the door is opened for longer than 2 minutes, the alarm is activated and a
sound can be heard 3 times per minute until the door is closed or a random key
is pressed.
In case of a power failure, the setting of the door open alarm will function
as set prior to the power failure, as soon as the refrigerator receives power
again.
FRESH BOX DRAWER – 0° DEGREE ZONE
Depending on the type of food you want to store in the fresh box, the
temperature can be changed with the slider.
Slide the slider left for fruits and vegetables.
Slide the slider to the right for meat and fish. This cools the fresh box
drawer more.
VEGETABLE & FRUIT DRAWER
The crisper drawer has a slider for moisture control. Slide the slider to the
right to increase the moisture. Slide the slider to the left to open the vents
to reduce the moisture inside the drawer.
Attention:
The ambient temperature, the frequency of opening the door and the position of
the appliance have an effect on the temperature in the appliance. Take this
into account when setting the thermostat.
- Do not place hot food in the appliance.
- You should never place hazardous, highly flammable or explosive substances such as alcohol, acetone or petrol in the appliance, because there will be a hazard of explosion.
- Carefully package meat and fish to prevent unpleasant smells.
- Leave sufficient space between the different foods, to allow the air to circulate properly.
- Do not place food against the rear wall of the appliance. The shelves have a stopper to prevent this.
- Do not leave the door open for longer than necessary.
Tips
- High ambient temperatures have a negative effect on energy use. Keep the appliance in a position away from direct sunlight or other sources of heat.
- Keep ventilation openings free. Clogged openings lead to higher use of energy.
- Try not to open the door too often, especially when the weather is wet and hot. Once you open the door, mind to close it as soon as possible.
- The space between the shelves and the rear wall of the refrigerator compartment must be unobstructed to allow the cool air to circulate. Therefore don’t place any food items against the back.
- Turn the thermostat to a lower setting when the circumstances allow it.
- Before storing fresh cooked food, make sure the food has cooled at least to room temperature.
- Ice and frost layer increase energy consumption, so clean the appliance as soon as the layer is 3 to 5 mm thick.
- If the gasket is damaged or if it turns out that the sealing is poor, the energy consumption is substantially higher. To restore efficiency, replace the gasket.
- Always consider the instructions, otherwise the energy consumption is substantially higher.
To avoid contamination of food, please respect the following instructions
- Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
- Clean regularly surfaces that can come in contact with food and accessible drainage systems.
- Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
- Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice cream and making ice cubes.
- One-, two- and three-start compartments are not suitable for the freezing of fresh food.
Order| Compartments TYPE| Target storage temp. [°C]|
Appropriate food
---|---|---|---
1| Fridge| +2 ~ +8| Eggs, cooked food, packaged food, fruits and vegetables,
dairy products, cakes, drinks and other foods are not suitable for freezing.
2| Freezer| ≤-18| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
3| Freezer| ≤-18| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
4| Freezer| ≤-12| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
5| Freezer| ≤-6| Seafood (fish, shrimp, shellfish), freshwater aquatic
products and meat products (recommended for 3 months, the longer the storage
time, the worse the taste and nutrition), suitable for frozen fresh food.
6| 0-star| -6 ~ 0| Fresh pork, beef, fish, chicken, some packaged processed
foods, etc. (Recommended to eat within the same day, preferably no more than 3
days).
Partially encapsulated processed foods (non-freezable foods).
7| Chill| -2 ~ +3| Fresh/ frozen pork, beef, chicken, freshwater aquatic
products, etc. (7 days below 0°C and above 0°C is recommended for consumption
within that day, preferably no more than 2 days). Seafood (less than 0 for 15
days, it is not recommended to store above 0°C.
8| Fresh food| 0 ~ +4| Fresh pork, beef, fish, chicken, cooked food, etc.
(Recommended to eat within the same day, preferably no more than 3 days)
9| Wine| +5 ~ +20| Red wine, white wine, sparkling wine, etc.
Note: please store different foods according to the compartments or target storage temperature of your purchased products.
- If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mold developing within the appliance.
Water dispenser cleaning (special for water dispenser products):
- Clean water tanks if they have not been used for 48 h; flush the water system connected to a water supply if water has not been drawn for 5 days.
WARNING: Food needs to be packed in bags before putting into the refrigerator, and liquids need to be packed in bottles or capped containers to avoid the problem that the product design structure is not easy to clean.
Cleaning & maintenance
Before cleaning the appliance, switch it off by removing the plug from the
socket.
Clean the interior of the appliance. Use warm soapy water with, for instance,
washing-up liquid, all-purpose cleaner
or soda in order to prevent nasty smells. Wipe the inside of the appliance
after cleaning with clean water and properly wipe everything dry. Leave the
appliance to dry for 1 to 2 hours.
The shelves, drawers and door compartments can be removed from the appliance
easily and washed by hand.
These components may not be cleaned in the dishwasher.
For areas in the refrigerator that are difficult to clean, such as small
openings or corners, it is recommended wiping them clean regularly with a soft
cloth or brush. If necessary, a tool can be used, such as thin sticks
(cocktail sticks, for example), to make sure no contamination can occur in
these areas.
Clean the outside of the refrigerator and the door rubbers with a soft damp
cloth.
Clean the rear of the refrigerator at least one per year with a vacuum cleaner
so that the condenser and ventilation holes remain clean and the refrigerator
is able to function as optimal as possible.
Do not use hard brushes, steel wool, abrasives (such as toothpaste), organic
solvents (such as alcohol, acetone, oil, etc.), boiling water, acid or
alkaline product to clean the refrigerator, as this could damage the surface
and interior
of the refrigerator. Boiling water and benzene could deform or damage plastic
components.
DEFROSTING
The freezer section of this appliance is free from frost – no-frost. If used
correctly, no ice will be formed.
If an ice layer is created after all, defrost the freezer section when the ice
layer has reached a thickness of 3 mm. Remove all products from the freezer
section. Store the frozen products on a cool location, packaged in newspapers
and blankets. Remove the plug from the socket and keep the door of the cooler
section closed while defrosting
the freezer section.
Defrost the freezer section Defrosting can be accelerated by placing a tray
with hot water in the freezer section.
Do not use sharp metal objects to scrape the freezer section clean, use a
plastic ice scraper.
Clean and dry the freezer section. Insert the plug in the socket and set the
thermostat to the required setting.
Place the frozen products back in the freezer section once it has reached the
required temperature.
Warning: Never remove ice with sharp objects, defrosting sprays, a hair
dryer, a heater or something similar.
This could lead to unsafe situations and cause irreparable damage to the
appliance
REPLACING LED LIGHTING
This appliance has been provided with LED lighting. This lighting lasts for a
longer period of time. When a LED lamp
in the appliance is broken, you are not able to replace it yourself. Contact
the Inventum service department.
Troubleshooting
| Breakdown | Cause | Solution |
|---|---|---|
| The appliance no longer works | There is an interruption in the power supply. |
- Check that the plug is properly inserted in the socket
- Check that the power cable is not damaged
- Check that there is voltage on the socket by connecting a different appliance, such as a night lamp
- Check that the appliance is on by setting the thermostat higher than 0
The interior lighting does not work.| The lamp is defective or the plug is not
in the socket.| Check the solutions above or have the lamp replaced.
Temperature in the refrigerator is too high or too low| Wrong setting of the
thermostat.| – turn the thermostat to a different position
The ambient temperature is higher or lower than the temperature indicated in
the table with technical data.| The appliance is intended for operation in an
ambient temperature indicated in the table with technical data supplied with
the appliance.
The appliance is located in direct sunlight or near a heat source.| Change the
location of the appliance according to the information in the instruction
manual.
A too large amount of hot food has been placed in the appliance at once.| Wait
72 hours until the products are frozen. The temperature in the appliance will
return to the required level.
The ventilation at the rear of the appliance is hindered.| Keep the appliance
10 cm away from the walls, for sufficient ventilation.
The door of the refrigerator is opened too frequently or remains open for too
long.| Open the door less often and/or reduce the time that the door remains
open.
The door is not closed properly.| Make sure the foods are placed in such a way
that they do not hinder the door when it is being closed.
The compressor does not work often enough.| Check that the ambient temperature
is not lower than the range of the climate class.
The door rubber is loose.| Fasten the door rubber or have it replaced.
The appliance is working continuously.| Wrong setting of the thermostat.| Turn
the thermostat to a higher position
There is water in the lower section of the refrigerator.| The opening of the
defrost water drain is clogged.| Clean the opening of the defrost water drain
by means of the skewer.
The ventilation within the cooler section is hindered.| Check that the food
does not make contact with the rear wall of the refrigerator.
Unusual or loud noises| The appliance is not level and stable.| Level the
appliance with the adjustable feet.
The appliance is standing against something.| Place the appliance in such a
way that it is not standing against anything.
During normal use of the cooling appliance, different types of noises can occur that do not have any effect on the correct operation of the freezer.
Noises that can be easily remedied:
- Noise due to the fact that the appliance is not level – position the appliance using the front adjustable feet. If necessary, place soft material under the rear wheels, particular in case of a tiled floor.
- Friction against other furniture – move the appliance.
- Grinding of drawers or shelves – remove the shelf or drawer and then place it back.
- Noise of colliding bottles – place the bottles apart.
Noises that can be heard during normal use of the appliance are caused by the operation of the thermostat, compressor (activation), cooling system (shrinkage and expansion of the material under the influence of temperature differences and flow of cooling liquid).
Product fiche
| INVENTUM
---|---
Model number| JVL2600
Type of appliance| refrigerator/freezer
Category| 7
Energy-efficiency class| A++
Annual energy consumption [Ace]| 216 kWh
Net capacity – total| 287 liters
Net capacity – cooling compartment| 207 liters
Net capacity – freezer compartment **| 80 liters
Max. storage time in case of power failure| 16 hours
Freezing capacity (kg/24 hour)| 8
Climate class| SN/N/ST
Noise level dB(A)| 39 dB
Type of appliance| stand
Defrosting system| no-frost
Execution**|
Color| inox
Number of doors| 2
Door opening reversible|
Egg holder included| 2
Ice cube holder included| 1
Number of glass shelves| 3
Number of freezer drawers| 3
Total amount of door compartments/ bottle racks| 3
Number of fresh box drawers (0° degree zone)| 1
Number of crisper drawers| 1
CFK/HFK free| free
Type of cooling agent| R600a
Number of compressors| 1
Technical specifications|
Dimensions (width) in cm| 59,5 x 59,0 x 178,5
Net weight in kg| 57 kg
Gross weight in kg| 62 kg
Power consumption [W]| 80 w
Rated voltage [V] / frequency [Hz]| 220-240V ~ 50Hz
Length of power cord [m]| 2,0
Type of plug| VDE plug 90°
References
- Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!
- Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>