Nedis FSBS120AT Bluetooth Speaker User Manual

: June 5, 2024
: nedis

FSBS120AT Bluetooth Speaker

Nedis FSBS120AT Bluetooth Speaker

User Manual

Preface

Thank you for purchasing the Nedis FSBS120AT.

This document is the user manual and contains all the information for correct, efficient and safe use of the product.

This user manual is addressed to the end user. Read this information carefully before installing or using the product.

Always store this information with the product for use in the future.

Product description

The Nedis FSBS120AT is a Bluetooth speaker which plays audio from your media device.

Intended use

This device is intended as an audio player.

Any modification of the product may have consequences for safety, warranty and proper functioning.

Specifications

Product

|

Bluetooth® speaker

---|---

Article number

|

FSBS120AT

Dimensions (l x w x h)

|

121 x 150 x 107 mm

Weight

|

738 g

Channels

|

Stereo via TWS

RMS audio output

|

2 x 5 W

Peak audio output

|

2 x 15 W

Sensitivity

|

85 dB

Bluetooth frequency range

|

2402 – 2480 MHz

Bluetooth® version

|

V5.0 + EDR

Transmission distance

|

10 m

Maximum transmission power

|

2 dBm

Maximum antenna gain

|

1 dBi

Battery type

|

Lithium-ion (18650)

Battery capacity

|

1200 mAh

Charging input power

|

5 V / 1 A

Charging time

|

± 3 hours

Playback / talk time

|

Up to 4 hours

Driver unit

|

Ø 52 mm

Impedance

|

4 Ω

Frequency response

|

100 Hz – 16 KHz

Parts list (Image A)

A

1. Speaker

2. Power button

3. Bluetooth indicator LED

4. Micro USB port

5. Status indicator LED

6. Audio port (3.5mm)

7. Micro USB cable

Safety instructions

WARNING

Only use the product as described in this manual.
Do not use the product if a part is damaged or defective. Replace a damaged or defective device immediately.
Do not immerse the product in water.
Do not charge when the product is wet.
Do not drop the product and avoid bumping.
his product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
Do not expose the product to direct sunlight, naked flames or heat.
Disconnect the product from the electrical outlet and other equipment if problems occur.

Installation

Check the contents of the package
Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.

Use

Power supply (Image B)

B

1. Plug the micro USB cable B 1 into the micro USB port of the product B 3.

2. Plug the other end of the micro USB cable B 1 into a USB power adapter to charge the product.

The charging indicator LED B 4 lights up red when charging.
The charging indicator LED B 4 stops lighting up when charging is complete.

Pair with one speaker

1. Hold the power button A 2 for 2 seconds to switch on the product.

The Bluetooth indicator LED A 3 starts flashing to indicate pairing mode is active.

2. Activate Bluetooth on your audio source and connect with the product (FSBS120).

3. If asked, enter the pairing code ‘0000’.

The Bluetooth indicator LED A 3lights up to indicate successful pairing.

Pair with both speakers

1. Hold the power button A 2 on both speakers for 2 seconds to switch them on.

After a few seconds, one of the two speakers emits a tone to indicate that it is paired with the other speaker.
The Bluetooth indicator LED A 3 lights up on of the speakers to indicate it is ready to pair with an audio source.
If pairing between the speakers fails, double press the power button A 2 to retry.

2. Activate Bluetooth on your audio source and connect with the product (FSBS120).

If the speakers are correctly paired to eachother, only one of them emits a Bluetooth signal. In case you see two signals, retry pairing the speakers to eachother.

3. If asked, enter the pairing code ‘0000’.

Connect with audio cable (Image B)

Audio cable is not included.

To pair the audio source to the product using an audio cable, follow these steps:

1. Hold the power button A 2 for 2 seconds to switch on the product.

2. Plug the audio cable B 2 into the audio port B 5 to connect the product to your media device.

Maintenance

Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.

Troubleshooting

Problem

|

Possible cause

|

Solution

---|---|---

The product does not switch on.

|

The batteries are drained.

|

Charge the product for at least 30 minutes and retry.

Audio source cannot pair with the product.

|

The audio source does not support A2DP.

|

Choose an audio source that supports A2DP.

Lost Bluetooth connection.

|

Navigate to Bluetooth settings on your audio source, tap FSBS120 and select “Forget”.

Restart both devices and try again.

No sound is coming from the product.

|

The product is not connected or paired to the audio source.

|

Connect the product to the audio source with an audio cable (not included) or pair with Bluetooth.

The product is too far out of reach from the audio source.

|

Bring the product and the audio source closer together.

The audio source volume is too low/muted.

|

Raise the volume of the audio source.

Warranty

Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.

Disclaimer

Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.

Disposal

|

This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.

---|---

Declaration of Conformity

We, Nedis B.V. declare as manufacturer that the product FSBS120AT from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.

The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via webshop.nedis.com/FSBS120AT#support

For additional information regarding the compliance, contact the customer service:

Web: www.nedis.com

E-mail: service@nedis.com

Phone: +31 (0)73-5991055 (during office hours)

Nedis B.V., de Tweeling 28

5215 MC ’s-Hertogenbosch, the Netherlands